Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM2040EQ _59 Vehicle Exterior _014733 WINDOW / GLASS _0075142 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch  


DESCRIPTION

If the manual up and down functions operate normally but the auto up and down functions do not, then fail-safe mode may be functioning.

If power window initialization (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION) has not been performed, the auto up and down functions will not operate.

WIRING DIAGRAM

B281016
0.271,2.292 2.281,2.708 2.01,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 0.969,3.365 2.615,3.521 1.646,0.156 10 false : LIN Communication Line 0.396,0.531 1.26,1.01 0.865,0.479 10 false from Auxiliary Battery 1.688,0.667 2.552,0.896 0.865,0.229 10 false DOOR NO. 2 2.521,2.406 4.479,2.948 1.958,0.542 10 false Power Window Regulator Motor Assembly (for Driver Door) 5.229,2.406 6.844,2.771 1.615,0.365 10 false Power Window Regulator Master Switch Assembly 2.521,2.25 2.875,2.458 0.354,0.208 10 false J9 5.229,2.26 5.708,2.542 0.479,0.281 10 false J10 1.635,1.594 2.01,1.75 0.375,0.156 10 false LIN2 2.833,1.448 3.094,1.604 0.26,0.156 10 false LIN 2.833,0.427 2.958,0.583 0.125,0.156 10 false B 3.802,0.427 4.208,0.583 0.406,0.156 10 false AUTO 5.375,0.521 5.656,0.75 0.281,0.229 10 false A 5.375,1.031 5.542,1.229 0.167,0.198 10 false D 5.375,1.531 5.542,1.729 0.167,0.198 10 false U 5.375,1.833 5.542,2.021 0.167,0.188 10 false E 3.729,0.927 4.24,1.083 0.51,0.156 10 false DWN1 3.906,1.448 4.281,1.667 0.375,0.219 10 false UP1 4.042,1.729 4.406,1.885 0.365,0.156 10 false E 4.25,1.729 4.375,1.885 0.125,0.156 10 false 1 4.25,0.938 4.375,1.094 0.125,0.156 10 false 7 5.188,0.927 5.792,1.156 0.604,0.229 10 false 5 5.198,1.438 5.875,1.656 0.677,0.219 10 false 1 5.198,1.729 5.75,1.917 0.552,0.188 10 false 9 4.25,0.427 4.375,0.583 0.125,0.156 10 false 4 5.198,0.438 5.854,0.688 0.656,0.25 10 false 4 4.25,1.448 4.438,1.604 0.188,0.156 10 false 10 2.646,0.427 2.771,0.583 0.125,0.156 10 false 2 2.635,1.448 2.813,1.604 0.177,0.156 10 false 9

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See pageVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the power window control system after confirming that the communication system is functioning properly.

·

If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

When the ECU determines that the power window regulator motor assembly (for driver door) has a malfunction, DTC B2311 is stored.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / D-Door Motor / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver door power window auto switch signal ON or OFF ON: Driver door power window auto switch operated
OFF: Driver door power window auto switch not operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Auto SW
50003 124 1
OK:

On the intelligent tester screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

2.PERFORM INITIALIZATION (DRIVER DOOR WINDOW MOTOR)

NG

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
2.PERFORM INITIALIZATION (DRIVER DOOR WINDOW MOTOR)
a.

Initialize the power window regulator motor assembly (for driver door).

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
a.

Check that the driver door power window moves when the auto up and down functions of the power window regulator master switch assembly are operated.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK

OK:

Driver door auto up and down functions are normal.



Result:
Proceed to
OK
NG



OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.
B164359
2.365,1.781 2.635,2.698 false 1.906,1.792 2.125,2.688 false 1.677,1.792 1.458,2.698 false 1.135,1.792 0.917,2.688 false 0.188,0.188 0.479,0.406 0.292,0.219 10 false *a 0.854,2.698 0.99,2.885 0.135,0.188 10 false E 1.406,2.698 1.542,2.885 0.135,0.188 10 false D 2.094,2.698 2.229,2.885 0.135,0.188 10 false A 2.615,2.698 2.75,2.885 0.135,0.188 10 false U
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Remove the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (U) - 9 (E) Auto UP Below 1 Ω
4 (A) - 9 (E) Auto UP Below 1 Ω
5 (D) - 9 (E) Auto DOWN Below 1 Ω
4 (A) - 9 (E) Auto DOWN Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR))

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR))
a.

Disconnect the power window regulator motor assembly (for driver door) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J10-4 (A) - J9-4 (AUTO) Always Below 1 Ω
J10-4 (A) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR