Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING
RM2040EQ _59 Vehicle Exterior _014734 SLIDING ROOF / CONVERTIBLE _0075145 SLIDING ROOF HOUSING A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING  DISASSEMBLY  


PROCEDURE

Hide 63260A 1.REMOVE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

a.
B279114
0.313,1.49 0.573,0.802 false 0.74,1.604 0.958,1 false 0.688,1.615 0.865,1.823 0.177,0.208 10 *2 0.229,1.542 0.385,1.688 0.156,0.146 10 *1
*1 Guide
*2 Pin


Disengage the claw.


b.

Disengage the guide and pin, and remove the map light bracket.


c.
B279115

Remove the 2 bolts and sliding roof drive gear sub-assembly.


Hide 63306 2.REMOVE SUNSHADE TRIM SUB-ASSEMBLY

a.
B279116

Remove the screw and the sliding roof piece sub-assembly LH.

HINT:

Use the same procedure for the RH side.



b.
B286382

Slide and remove the sunshade trim sub-assembly.


Hide 63214F 3.REMOVE REAR SLIDING ROOF PANEL

a.
B286383
0.323,2.396 0.521,2.563 0.198,0.167 10 false (1) 2.26,0.667 2.458,0.833 0.198,0.167 10 false (2)

Using a screwdriver, disengage the 2 claws. Then slide the rear sliding roof panel rearward to remove it.

HINT:

Tape the screwdriver tip before use.



Hide 63205A 4.REMOVE SLIDING ROOF DRIVE CABLE SUB-ASSEMBLY

NOTICE:

Do not disassemble the sliding roof drive cable sub-assembly except when replacing it.


a.
B279124

Hold down the roof wind deflector panel sub-assembly.


b.
B279121
1.99,1.406 1.552,1.573 false 1.375,1.479 1.531,1.625 0.156,0.146 10 false *1
*1 Protective Tape


Using a screwdriver, slide the sliding roof drive cable sub-assembly in the direction indicated by the arrow in the illustration to remove it.

HINT:
·

Tape the screwdriver tip before use.

·

Use the same procedure for the other sliding roof drive cable sub-assembly.




Hide 63209 5.REMOVE ROOF WIND DEFLECTOR PANEL SUB-ASSEMBLY

a.
B279125
0.271,0.698 0.188,0.448 false 0.729,0.677 0.573,0.396 false 2.542,1.927 2.229,1.979 false 2.656,1.5 2.354,1.552 false 0.188,0.698 0.344,0.844 0.156,0.146 10 false *2 0.646,0.698 0.802,0.844 0.156,0.146 10 false *1 1.208,1.833 1.448,2.021 0.24,0.188 10 true (1) 1.896,0.281 2.094,0.448 0.198,0.167 10 false (2) 2.052,1.896 2.208,2.042 0.156,0.146 10 false *2 2.198,1.469 2.354,1.615 0.156,0.146 10 false *1
*1 Spring
*2 Guide


Pull the spring in the direction indicated by the arrow (1) in the illustration to disengage the 2 springs.


b.

Pull the roof wind deflector panel sub-assembly in the direction indicated by the arrow (2) in the illustration to disengage the 2 guides and remove it.