Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING
RM2040EQ _59 Vehicle Exterior _014734 SLIDING ROOF / CONVERTIBLE _0075145 SLIDING ROOF HOUSING A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING  REASSEMBLY  


PROCEDURE

Hide 63209 1.INSTALL ROOF WIND DEFLECTOR PANEL SUB-ASSEMBLY

a.
B279126
0.24,0.729 0.188,0.448 false 0.51,0.406 0.719,0.688 false 2.25,1.531 2.656,1.479 false 2.125,1.958 2.542,1.906 false 0.688,0.698 0.844,0.844 0.156,0.146 10 false *2 0.156,0.719 0.313,0.865 0.156,0.146 10 false *1 1.948,1.865 2.104,2.01 0.156,0.146 10 false *1 2.083,1.438 2.24,1.583 0.156,0.146 10 false *2 0.552,1.677 0.76,1.854 0.208,0.177 10 true (2) 1.938,0.198 2.135,0.365 0.198,0.167 10 false (1)
*1 Guide
*2 Spring


Engage the 2 guides in the direction indicated by the arrow (1) in the illustration to install the roof wind deflector panel sub-assembly.


b.

Engage the 2 springs in the direction indicated by the arrow (2) in the illustration.

NOTICE:

Make sure that the springs are securely installed.



Hide 63205A 2.INSTALL SLIDING ROOF DRIVE CABLE SUB-ASSEMBLY

a.
B279124

Hold down the roof wind deflector panel sub-assembly.


b.
B279122
2.23,0.919 2.388,1.069 0.158,0.149 10 *1 2.842,1.058 2.415,0.999 false
*1 Protective Tape


Using a screwdriver, slide the sliding roof drive cable sub-assembly in the direction indicated by the arrow in the illustration to install it.

HINT:
·

Tape the screwdriver tip before use.

·

Use the same procedure for the other sliding roof drive cable sub-assembly.




Hide 63214F 3.INSTALL REAR SLIDING ROOF PANEL

a.
B286384
2.24,0.677 2.438,0.844 0.198,0.167 10 (1) 1.052,2.708 1.25,2.875 0.198,0.167 10 (2)

Insert the rear sliding roof panel in the direction indicated by the arrow (1) in the illustration.


b.

Engage the 2 claws in the direction indicated by the arrow (2) in the illustration to install the rear sliding roof panel.


Hide 4.ADJUST FULLY CLOSED POSITION

a.
B286385
1.583,0.49 1.177,0.24 false 1.563,0.667 1.021,0.906 false 1.021,0.156 1.177,0.302 0.156,0.146 10 *1 0.823,0.823 0.979,0.969 0.156,0.146 10 *1
*1 Alignment Mark


Using a screwdriver, slide the sliding roof drive cable sub-assembly in either direction indicated by the arrows in the illustration and alignment marks.

HINT:

Tape the screwdriver tip before use.



Hide 63306 5.INSTALL SUNSHADE TRIM SUB-ASSEMBLY

a.
B286387

Insert the sunshade trim sub-assembly into the sliding roof housing sub-assembly.


b.
B279116

Install the sliding roof piece sub-assembly LH with the screw.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)

HINT:

Use the same procedure for the RH side.



Hide 63260A 6.INSTALL SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

a.
B279115

Install the sliding roof drive gear sub-assembly with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


b.
B279114
0.406,1.521 0.656,0.792 false 0.854,1.615 0.958,1.021 false 0.771,1.688 0.927,1.833 0.156,0.146 10 *2 0.313,1.552 0.469,1.698 0.156,0.146 10 *1
*1 Guide
*2 Pin


Engage the guide and pin.


c.

Engage the claw and install the map light bracket.