Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM
RM2040EQ _59 Vehicle Exterior _014734 SLIDING ROOF / CONVERTIBLE _0075147 SLIDING ROOF SYSTEM J

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  Sliding Roof does not Move by Operating Sliding Roof Control Switch  


DESCRIPTION

The sliding roof ECU (sliding roof drive gear sub-assembly) receives slide and tilt signals when the sliding roof switch is operated and drives its built-in motor.

WIRING DIAGRAM

B278886
4.646,4.927 6.531,5.385 1.885,0.458 10 false Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly) 4.646,4.76 5.01,4.938 0.365,0.177 10 false S4 1.771,4.385 4.896,4.615 3.125,0.229 10 false Sliding Roof Switch (Roof Console Box Assembly) 1.771,4.219 2.24,4.5 0.469,0.281 10 false S12 3.385,1.844 3.99,2.031 0.604,0.188 10 false S/ROOF 0.115,1.677 1.542,2.063 1.427,0.385 10 false from Auxiliary Battery 5.031,1.688 5.208,1.906 0.177,0.219 10 false B 5.031,2.792 5.417,2.99 0.385,0.198 10 false OPN 5.031,3.031 5.396,3.24 0.365,0.208 10 false CLS 5.031,3.802 5.302,3.979 0.271,0.177 10 false UP 5.031,3.542 5.563,3.719 0.531,0.177 10 false DWN 4.875,2.708 5.01,2.885 0.135,0.177 10 false 7 4.875,2.958 5.01,3.135 0.135,0.177 10 false 5 4.875,3.469 5.01,3.646 0.135,0.177 10 false 6 4.875,3.719 4.979,3.896 0.104,0.177 10 false 4 4.875,1.583 5.031,1.781 0.156,0.198 10 false 8 3.75,2.719 4.125,2.906 0.375,0.188 10 false OPN 3.771,2.958 4.146,3.146 0.375,0.188 10 false CLS 3.594,3.458 4.188,3.729 0.594,0.271 10 false DOWN 3.854,3.708 4.156,3.927 0.302,0.219 10 false UP 4.115,2.708 4.24,2.885 0.125,0.177 10 false 3 4.115,2.948 4.24,3.125 0.125,0.177 10 false 2 4.115,3.708 4.229,3.885 0.115,0.177 10 false 5 4.115,3.458 4.25,3.635 0.135,0.177 10 false 4 2.396,2.833 2.76,3.031 0.365,0.198 10 false GND 2.219,2.833 2.333,3.01 0.115,0.177 10 false 1 5.813,4.104 5.99,4.344 0.177,0.24 10 false E 5.979,4 6.177,4.177 0.198,0.177 10 false 12 1.104,1.021 4.083,1.333 2.979,0.313 10 false Main Body ECU (Multiplex Network Body ECU) 2.948,0.563 3.302,0.75 0.354,0.188 10 false LIN2 5.042,0.552 5.479,0.74 0.438,0.188 10 false MPX1 0.677,5.396 2.323,5.583 1.646,0.188 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear sub-assembly) must be initialized (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION).

·

The sliding roof system uses the LIN communication system. First, confirm that there are no malfunctions in the LIN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

When a sliding roof ECU (sliding roof drive gear sub-assembly) DTC is output, first perform troubleshooting for the sliding roof ECU (sliding roof drive gear sub-assembly) DTC.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch to on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Sliding Roof / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Sliding Roof > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Open Switch OPEN switch signal ON or OFF ON: OPEN switch pressed
OFF: OPEN switch not pressed
-
Close Switch CLOSE switch signal ON or OFF ON: CLOSE switch pressed
OFF: CLOSE switch not pressed
-
Up Switch UP switch signal ON or OFF ON: UP switch pressed
OFF: UP switch not pressed
-
Down Switch DOWN switch signal ON or OFF ON: DOWN switch pressed
OFF: DOWN switch not pressed
-
Body Electrical > Sliding Roof > Data List
Tester Display
Open Switch
Close Switch
Up Switch
Down Switch
50003 147 1,4,7,10
OK:

The intelligent tester display changes according to switch operation as shown in the table.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - AUXILIARY BATTERY AND BODY GROUND)

NG

3.INSPECT SLIDING ROOF SWITCH (ROOF CONSOLE BOX ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
S4-8 (B) - Body ground Power switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S4-12 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SLIDING ROOF SWITCH (ROOF CONSOLE BOX ASSEMBLY)
a.
B270995
0.514,3.003 0.687,3.163 0.174,0.16 10 *a 1.362,3.272 1.578,3.425 0.215,0.153 10 UP 1.183,3.031 1.648,3.184 0.465,0.153 10 DOWN 2.206,3.031 2.529,3.184 0.323,0.153 10 OPN 2.336,3.272 2.659,3.425 0.323,0.153 10 CLS 2.641,3.803 2.991,3.955 0.351,0.153 10 GND 1.788,3.838 1.788,3.351 1.788,3.351 1.626,3.351 false 2.142,3.838 2.142,3.351 2.142,3.351 2.303,3.351 false 2.026,3.838 2.026,3.107 2.026,3.107 2.171,3.107 false 1.896,3.838 1.896,3.107 1.896,3.107 1.751,3.107 false 2.298,3.885 2.62,3.885 false
*a Component without harness connected
(Sliding Roof Switch (Roof Console Box Assembly))


Remove the sliding roof switch (roof console box assembly).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (UP) - 1 (GND) UP switch is pressed Below 1 Ω
5 (UP) - 1 (GND) UP switch is not pressed 10 kΩ or higher
4 (DOWN) - 1 (GND) DOWN switch is pressed Below 1 Ω
4 (DOWN) - 1 (GND) DOWN switch is not pressed 10 kΩ or higher
3 (OPN) - 1 (GND) OPEN switch is pressed Below 1 Ω
3 (OPN) - 1 (GND) OPEN switch is not pressed 10 kΩ or higher
2 (CLS) - 1 (GND) CLOSE switch is pressed Below 1 Ω
2 (CLS) - 1 (GND) CLOSE switch is not pressed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF SWITCH AND BODY GROUND)

NG

REPLACE SLIDING ROOF SWITCH (ROOF CONSOLE BOX ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF SWITCH AND BODY GROUND)
a.

Disconnect the S12 sliding roof switch (roof console box assembly) connector.


b.

Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S4-5 (CLS) - S12-2 (CLS) Always Below 1 Ω
S4-5 (CLS) - Body ground Always 10 kΩ or higher
S4-7 (OPN) - S12-3 (OPN) Always Below 1 Ω
S4-7 (OPN) - Body ground Always 10 kΩ or higher
S4-6 (DWN) - S12-4 (DOWN) Always Below 1 Ω
S4-6 (DWN) - Body ground Always 10 kΩ or higher
S4-4 (UP) - S12-5 (UP) Always Below 1 Ω
S4-4 (UP) - Body ground Always 10 kΩ or higher
S12-1 (GND) - Body ground Always Below 1 Ω
S4-12 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR