Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Memory)
RM2040EQ _59 Vehicle Exterior _014736 MIRROR (EXT) _0075158 POWER MIRROR CONTROL SYSTEM(w/ Memory) U

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  TERMINALS OF ECU  


CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)


B209687
4.052,0.24 4.375,0.448 0.323,0.208 2.979,0.24 3.302,0.448 0.323,0.208 4.104,0.25 4.729,0.625 0.625,0.375 10 false J13 3.031,0.25 3.542,0.594 0.51,0.344 10 false z17

a.

Disconnect the J13 connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
J13-14 (BDR) - Body ground W - Body ground +B power supply Always 11 to 14 V
J13-6 (CPUB) - Body ground W - Body ground +B power supply Always 11 to 14 V
J13-5 (SIG) - Body ground BE - Body ground Ignition power supply Power switch off → on (IG) 0 V → 11 to 14 V
J13-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the J13 connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
z17-1 (RMVR) - z17-9 (RMHR) B - W Vertical mirror motor drive voltage RH mirror surface moving upward → stopped 11 to 14 V → 0 V
z17-10 (RM+R) - z17-1 (RMVR) BR - W Vertical mirror motor drive voltage RH mirror surface moving downward → stopped 11 to 14 V → 0 V
z17-10 (RM+R) - z17-9 (RMHR) BR - B Horizontal mirror motor drive voltage RH mirror surface moving right → stopped 11 to 14 V → 0 V
z17-9 (RMHR) - z17-1 (RMVR) W - B Horizontal mirror motor drive voltage RH mirror surface moving left → stopped 11 to 14 V → 0 V
z17-5 (RVC) - z17-14 (RE1) GR - R Mirror position sensor power supply Power switch on (IG) 4.55 to 5.45 V
z17-6 (VSSR) - z17-14 (RE1) G - R Mirror position sensor signal Power switch on (IG) 0.96 to 4.04 V
z17-13 (HSSR) - z17-14 (RE1) L - R Mirror position sensor signal Power switch on (IG) 0.96 to 4.04 V
J13-3 (M2) - J13-13 (MSWE) B - V M2 switch signal for seat memory switch M2 switch on Below 1 V
M2 switch off 11 to 14 V
J13-2 (M1) - J13-13 (MSWE) G - V M1 switch signal for seat memory switch M1 switch on Below 1 V
M1 switch off 11 to 14 V
J13-1 (MM) - J13-13 (MSWE) P - V SET switch signal for seat memory switch SET switch on Below 1 V
SET switch off 11 to 14 V



CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)


B209687
2.948,0.25 3.271,0.458 0.323,0.208 4.063,0.25 4.385,0.458 0.323,0.208 3,0.26 3.469,0.521 0.469,0.26 10 false z16 4.104,0.26 4.531,0.552 0.427,0.292 10 false K12

a.

Disconnect the K12 connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
K12-14 (BDR) - Body ground GR - Body ground +B power supply Always 11 to 14 V
K12-6 (CPUB) - Body ground W - Body ground +B power supply Always 11 to 14 V
K12-5 (SIG) - Body ground GR - Body ground Ignition power supply Power switch off → on (IG) 0 V → 11 to 14 V
K12-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the K12 connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
z16-1 (LMVR) - z16-9 (LMHR) B - W Vertical mirror motor drive voltage LH mirror surface moving upward → stopped 11 to 14 V → 0 V
z16-10 (LM+R) - z16-1 (LMVR) BR - B Vertical mirror motor drive voltage LH mirror surface moving downward → stopped 11 to 14 V → 0 V
z16-10 (LM+R) - z16-9 (LMHR) BR - W Horizontal mirror motor drive voltage LH mirror surface moving right → stopped 11 to 14 V → 0 V
z16-9 (LMHR) - z16-1 (LMVR) W - B Horizontal mirror motor drive voltage LH mirror surface moving left → stopped 11 to 14 V → 0 V
z16-5 (LVC) - z16-14 (LE1) GR - R Mirror position sensor power supply Power switch on (IG) 4.55 to 5.45 V
z16-6 (VSSR) - z16-14 (LE1) G - R Mirror position sensor signal Power switch on (IG) 0.96 to 4.04 V
z16-13 (HSSR) - z16-14 (LE1) L - R Mirror position sensor signal Power switch on (IG) 0.96 to 4.04 V