Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR
RM2040EQ _59 Vehicle Exterior _014736 MIRROR (EXT) _0075160 OUTER REAR VIEW MIRROR G

MIRROR (EXT)  OUTER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87908B 1.INSPECT MIRROR SUB-ASSEMBLY RH (w/ Memory)

a.
B294037
1.271,2.5 0.906,2.5 false 1.427,2.74 1.427,3.167 1.427,3.167 1.698,3.167 false 1.302,2.74 1.302,3.167 1.302,3.167 1.042,3.167 false 1.75,3.083 2.417,3.365 0.667,0.281 10 false RM+R 0.26,0.177 0.688,0.479 0.427,0.302 10 false *a 0.594,3.083 1.281,3.354 0.688,0.271 10 false RMHR 0.458,2.417 1.042,2.719 0.583,0.302 10 false RMVR
*a Component without harness connected
(Mirror Sub-assembly RH)


Check the operation of the mirror surface.

i.

Disconnect the mirror sub-assembly RH connector.


ii.

Apply auxiliary battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Auxiliary battery positive (+) → Terminal 1 (RMVR)
Auxiliary battery negative (-) → Terminal 10 (RM+R)
Turns upward
Auxiliary battery positive (+) → Terminal 10 (RM+R)
Auxiliary battery negative (-) → Terminal 1 (RMVR)
Turns downward
Auxiliary battery positive (+) → Terminal 9 (RMHR)
Auxiliary battery negative (-) → Terminal 10 (RM+R)
Turns left
Auxiliary battery positive (+) → Terminal 10 (RM+R)
Auxiliary battery negative (-) → Terminal 9 (RMHR)
Turns right


If the result is not as specified, replace the mirror sub-assembly RH.



Hide 87909B 2.INSPECT MIRROR SUB-ASSEMBLY LH (w/ Memory)

a.
B294038
1.26,2.479 0.802,2.479 false 1.438,2.729 1.438,3.198 1.438,3.198 1.615,3.198 false 1.313,2.729 1.313,3.198 1.313,3.198 1.125,3.198 false 0.167,0.135 0.667,0.573 0.5,0.438 10 false *a 0.375,2.396 1.125,2.792 0.75,0.396 10 false LMVR 1.667,3.115 2.417,3.396 0.75,0.281 10 false LM+R 0.698,3.115 1.406,3.385 0.708,0.271 10 false LMHR
*a Component without harness connected
(Mirror Sub-assembly LH)


Check the operation of the mirror surface.

i.

Disconnect the mirror sub-assembly LH connector.


ii.

Apply auxiliary battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Auxiliary battery positive (+) → Terminal 1 (LMVR)
Auxiliary battery negative (-) → Terminal 10 (LM+R)
Turns upward
Auxiliary battery positive (+) → Terminal 10 (LM+R)
Auxiliary battery negative (-) → Terminal 1 (LMVR)
Turns downward
Auxiliary battery positive (+) → Terminal 9 (LMHR)
Auxiliary battery negative (-) → Terminal 10 (LM+R)
Turns left
Auxiliary battery positive (+) → Terminal 10 (LM+R)
Auxiliary battery negative (-) → Terminal 9 (LMHR)
Turns right


If the result is not as specified, replace the mirror sub-assembly LH.



Hide 87908B 3.INSPECT MIRROR SUB-ASSEMBLY RH (w/o Memory)

a.

Check the operation of the mirror surface.

i.
B281817
2.125,2.802 1.698,2.802 false 2.167,2.51 2.167,1.844 2.167,1.844 1.885,1.844 false 2.5,2.51 2.5,1.844 2.5,1.844 2.823,1.844 false 0.083,0.052 0.521,0.365 0.438,0.313 10 false *a 2.833,1.76 3.313,2.135 0.479,0.375 10 false MV 1.615,1.76 2.094,2.104 0.479,0.344 10 false MH 1.396,2.74 1.906,3.031 0.51,0.292 10 false M+
*a Component without harness connected
(Mirror Sub-assembly RH)


Disconnect the mirror sub-assembly RH connector.


ii.

Apply auxiliary battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Auxiliary battery positive (+) → Terminal 3 (MV)
Auxiliary battery negative (-) → Terminal 4 (M+)
Turns upward
Auxiliary battery positive (+) → Terminal 4 (M+)
Auxiliary battery negative (-) → Terminal 3 (MV)
Turns downward
Auxiliary battery positive (+) → Terminal 1 (MH)
Auxiliary battery negative (-) → Terminal 4 (M+)
Turns left
Auxiliary battery positive (+) → Terminal 4 (M+)
Auxiliary battery negative (-) → Terminal 1 (MH)
Turns right


If the result is not as specified, replace the mirror sub-assembly RH.



Hide 87909B 4.INSPECT MIRROR SUB-ASSEMBLY LH (w/o Memory)

a.

Check the operation of the mirror surface.

i.
B281821
0.781,2.521 0.781,1.823 0.781,1.823 0.563,1.823 false 1.125,2.521 1.125,1.823 1.125,1.823 1.406,1.823 false 0.802,2.875 0.802,3.26 0.802,3.26 1.302,3.26 false 0.104,0.063 0.635,0.542 0.531,0.479 10 false *a 1.344,3.156 1.927,3.396 0.583,0.24 10 false M+ 1.448,1.75 2.104,2.188 0.656,0.438 10 false MV 0.24,1.75 0.75,2.063 0.51,0.313 10 false MH
*a Component without harness connected
(Mirror Sub-assembly LH)


Disconnect the mirror sub-assembly LH connector.


ii.

Apply auxiliary battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Auxiliary battery positive (+) → Terminal 3 (MV)
Auxiliary battery negative (-) → Terminal 4 (M+)
Turns upward
Auxiliary battery positive (+) → Terminal 4 (M+)
Auxiliary battery negative (-) → Terminal 3 (MV)
Turns downward
Auxiliary battery positive (+) → Terminal 1 (MH)
Auxiliary battery negative (-) → Terminal 4 (M+)
Turns left
Auxiliary battery positive (+) → Terminal 4 (M+)
Auxiliary battery negative (-) → Terminal 1 (MH)
Turns right


If the result is not as specified, replace the mirror sub-assembly LH.