Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH
RM2040EQ _59 Vehicle Exterior _014736 MIRROR (EXT) _0075163 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Memory)

a.
B294031
1.729,0.844 1.729,0.292 1.729,0.292 1.906,0.292 false 1.719,1.854 1.719,2.385 1.719,2.385 1.896,2.385 false 1.979,3.771 1.979,4.302 1.979,4.302 1.708,4.302 false 2.146,3.771 2.146,4.427 2.146,4.427 2.51,4.427 false 2.333,3.771 2.333,4.135 2.333,4.135 2.51,4.135 false 1.417,4.219 1.844,4.469 0.427,0.25 10 false M+ 1.938,2.313 2.625,2.635 0.688,0.323 10 false *1 1.938,0.188 2.427,0.573 0.49,0.385 10 false *2 2.563,4.333 2.938,4.573 0.375,0.24 10 false E 2.563,4.042 3.104,4.313 0.542,0.271 10 false MSW 0.521,2.76 0.917,3.094 0.396,0.333 10 false *a
*1 Mirror Adjust Switch
*2 Mirror Select Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)


Check the switch functions.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (M+) - 2 (E) Mirror adjust switch pressed up 90 to 110 Ω
Mirror adjust switch pressed down 437 to 503 Ω
Mirror adjust switch pressed left 744 to 856 Ω
Mirror adjust switch pressed right 225 to 275 Ω
Mirror adjust switch not pressed 10 kΩ or higher
1 (MSW) - 2 (E) Mirror select switch R Below 1 Ω
Mirror select switch L 90 to 110 Ω
Mirror select switch off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Memory)

a.

w/o Retract mirror

i.

Check the mirror select switch and mirror surface adjust switch.


ii.
B254350
1.698,3.688 1.469,4.156 false 1.604,3.688 1.125,4.156 false 1.5,3.688 0.76,4.156 false 1.385,3.698 0.427,4.156 false 1.823,3.698 1.896,4.156 false 1.938,3.688 2.344,4.156 false 2.073,3.688 2.802,4.156 false 1.729,0.854 1.729,0.406 1.729,0.406 1.542,0.406 false 1.719,1.865 1.719,2.26 1.719,2.26 1.948,2.26 false 0.521,2.823 0.969,3.156 0.448,0.333 10 false *a 2.625,4.167 3.167,4.51 0.542,0.344 10 false MRH 2.167,4.167 2.604,4.469 0.438,0.302 10 false MRV 1.74,4.167 2.156,4.49 0.417,0.323 10 false MLV 1.281,4.167 1.75,4.49 0.469,0.323 10 false MLH 0.958,4.167 1.302,4.469 0.344,0.302 10 false M+ 0.656,4.167 0.958,4.479 0.302,0.313 10 false E 0.323,4.167 0.625,4.448 0.302,0.281 10 false B 1.333,0.323 1.792,0.667 0.458,0.344 10 false *1 1.99,2.167 2.406,2.51 0.417,0.344 10 false *2
*1 Mirror select switch
*2 Mirror surface adjust switch
*a Component without harness connected
(Outer Mirror Switch Assembly)


Turn the mirror select switch to the L position.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Switch Condition Specified Condition
4 (MLV) - 8 (B)
6 (M+) - 7 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
4 (MLV) - 7 (E)
6 (M+) - 8 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
5 (MLH) - 8 (B)
6 (M+) - 7 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
5 (MLH) - 7 (E)
6 (M+) - 8 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher



iv.

Turn the mirror select switch to the R position.


v.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Switch Condition Specified Condition
3 (MRV) - 8 (B)
6 (M+) - 7 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
3 (MRV) - 7 (E)
6 (M+) - 8 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
2 (MRH) - 8 (B)
6 (M+) - 7 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
2 (MRH) - 7 (E)
6 (M+) - 8 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.