Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH
RM2040EQ _59 Vehicle Exterior _014737 WIPER / WASHER _0075169 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT FRONT WIPER INTERMITTENT OPERATION (W/O AUTO WIPER SYSTEM)

a.
E226489
0.177,1.115 0.635,1.385 0.458,0.271 2.813,1.115 3.271,1.385 0.458,0.271 0.865,1.844 0.948,1.469 false 2.281,1.094 2.813,0.719 false 0.167,0.167 0.583,0.417 0.417,0.25 10 false *a 0.313,1.167 0.677,1.396 0.365,0.229 10 false I31 2.938,1.156 3.281,1.448 0.344,0.292 10 false I32 2.854,0.615 3.198,0.833 0.344,0.219 10 false +1 0.729,1.844 1.135,2.104 0.406,0.26 10 false EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Check the front wiper intermittent operation.

i.

Connect a voltmeter positive (+) lead to terminal I32-2 (+1) and a negative (-) lead to terminal I31-7 (EW).


ii.

Turn the power switch on (IG).


iii.

Turn the wiper switch to the INT position.


iv.

Operate the intermittent wiper relay and check the voltage between terminals I32-2 (+1) and I31-7 (EW).

OK:

Voltage changes as shown in the illustration.


E136493
2.625,0.104 3.104,0.271 0.479,0.167 10 false FAST: 1.927,0.385 2.615,0.563 0.688,0.177 10 false 11 to 14 V 2.344,0.885 2.594,1.063 0.25,0.177 10 false 0 V 3.177,1.385 3.531,1.563 0.354,0.177 10 false Start 0.073,0.5 1.719,1.177 1.646,0.677 10 false Voltage between terminals I32-3 (+1) and I31-7 (EW): 0.771,1.375 1.854,1.552 1.083,0.177 10 false Wiper Operation: 3.354,1 4.542,1.198 1.188,0.198 10 false 1.6 +/- 1 seconds 5.792,1 7.021,1.198 1.229,0.198 10 false 10.7 +/- 5 seconds 2.729,1.385 3.083,1.563 0.354,0.177 10 false Stop 5.583,1.385 5.938,1.563 0.354,0.177 10 false Start 4.792,1.385 5.146,1.563 0.354,0.177 10 false Stop 4.438,0.104 4.979,0.302 0.542,0.198 10 false SLOW:

If the result is not as specified, replace the windshield wiper switch assembly.



Hide 2.INSPECT FRONT WASHER OPERATION

a.
E226489
0.177,1.115 0.635,1.385 0.458,0.271 2.813,1.115 3.271,1.385 0.458,0.271 0.865,1.833 0.948,1.458 false 2.271,1.094 2.802,0.719 false 0.167,0.167 0.583,0.417 0.417,0.25 10 false *a 0.323,1.167 0.656,1.417 0.333,0.25 10 false I31 2.948,1.156 3.292,1.406 0.344,0.25 10 false I32 2.823,0.604 3.115,0.823 0.292,0.219 10 false +1 0.719,1.844 1.25,2.104 0.531,0.26 10 false EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Check the front washer operation.

i.

Connect a voltmeter positive (+) lead to terminal I32-2 (+1) and a negative (-) lead to terminal I31-7 (EW).


ii.

Turn the power switch on (IG).


iii.

Turn the washer switch on and off, and check the voltage between terminals I32-2 (+1) and I31-7 (EW).

OK:

Voltage changes as shown in the illustration.


E226602
4.094,1.333 4.021,1.5 false 4.76,1.333 4.844,1.51 false 0.969,0.823 2.625,1.375 1.656,0.552 10 false Voltage between terminals I32-3 (+1) and I31-7 (EW): 1.677,0.208 2.667,0.542 0.99,0.333 10 false Washer Switch: 2.49,1.5 4.49,1.75 2,0.25 10 false Approximately 0.5 seconds 4.573,1.49 6.51,1.75 1.938,0.26 10 false Approximately 2.2 seconds 2.958,0.792 3.792,1.156 0.833,0.365 10 false 11 to 14 V 3.375,1.135 3.833,1.542 0.458,0.406 10 false 0 V 3.302,0.438 3.813,0.833 0.51,0.396 10 false OFF 3.344,0.219 3.74,0.552 0.396,0.333 10 false ON

If the result is not as specified, replace the windshield wiper switch assembly.