Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2012.02–2014.05
RM2040EQ _59 Vehicle Exterior _014737 WIPER / WASHER _0075172 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Speed Signal Circuit  


DESCRIPTION

The windshield wiper relay assembly receives a vehicle speed signal from the combination meter assembly to control the automatic windshield wiper system.

A voltage of 12 V or 5 V is output from the combination meter assembly and then input to the skid control ECU.

A voltage of 12 V or 5 V is output from each ECU or relay and then input to the combination meter assembly.

The signal is changed to a pulse signal at the transistor in the combination meter assembly.

Each ECU controls the respective system based on the pulse signal.

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.

WIRING DIAGRAM

E237358E01
0.427,1.637 1.550,1.788 1.123,0.151 10 Skid Control ECU 0.994,0.794 1.285,0.945 0.292,0.151 10 SP1 0.093,1.637 0.411,1.818 0.319,0.181 10 A28 0.61,4.649 2.381,4.974 1.772,0.324 10 Stereo Component Amplifier Assembly*2 0.317,4.649 0.636,4.830 0.319,0.181 10 I69 1.362,0.794 1.549,0.943 0.187,0.148 10 11 0.459,3.124 2.548,3.288 2.089,0.164 10 Power Management Control ECU 0.459,2.971 0.749,3.135 0.290,0.164 10 I3 1.624,2.719 2.025,2.873 0.400,0.154 10 SPDI 2.095,2.719 2.275,2.877 0.180,0.159 10 14 2.936,2.719 3.116,2.877 0.180,0.159 10 21 3.952,2.719 4.131,2.877 0.180,0.159 10 18 3.952,4.24 4.131,4.399 0.180,0.159 10 17 2.936,5.717 3.116,5.876 0.180,0.159 10 20 5.383,0.794 5.687,0.944 0.304,0.150 10 8 5.384,2.719 5.659,2.868 0.275,0.150 10 9 5.604,0.879 5.803,1.028 0.198,0.150 10 SI 5.598,2.817 5.799,2.968 0.201,0.151 10 +S 4.992,3.164 5.287,3.310 0.295,0.145 10 I18 5.264,3.164 7.100,3.320 1.835,0.156 10 Combination Meter Assembly 5.575,4.24 5.904,4.385 0.328,0.145 10 SPD 5.313,4.24 5.625,4.402 0.311,0.162 10 17 5.575,5.739 5.904,5.885 0.328,0.145 10 SPD 5.299,5.739 5.485,5.901 0.186,0.162 10 17 4.796,6.111 5.267,6.272 0.471,0.162 10 I67 5.037,6.111 7.125,6.301 2.088,0.190 10 Navigation ECU Sub-assembly*2 2.936,4.24 3.116,4.399 0.180,0.159 10 19 1.654,4.24 1.982,4.385 0.328,0.145 10 SPD 2.095,4.24 2.268,4.402 0.172,0.162 10 11 4.259,4.629 4.563,4.788 0.304,0.159 10 I155 4.609,4.629 7.122,4.816 2.513,0.187 10 Radio and Display Receiver Assembly*1 3.118,6.129 4.338,6.291 1.220,0.162 10 Junction Connector 2.778,6.129 3.178,6.293 0.400,0.164 10 I124 2.095,5.717 2.407,5.878 0.311,0.162 10 24 0.32,6.129 2.651,6.305 2.331,0.176 10 Windshield Wiper Relay Assembly*3 0.556,7.136 3.056,7.311 2.500,0.176 10 *1: for Radio and Display Type 2.797,7.136 4.818,7.311 2.021,0.176 10 *2: for Navigation Receiver Type 1.654,5.717 1.982,5.862 0.328,0.145 10 SPD 0.063,6.129 0.341,6.282 0.277,0.153 10 I72 5.123,7.136 6.774,7.311 1.651,0.176 10 *3: w/ Auto Wiper System

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (SPEED SENSOR SIGNAL)
a.
E277112C01
1.5,0.354 1.854,0.604 0.354,0.25 1.156,2.135 1.396,1.406 false 2.802,3.646 3.26,3.844 0.458,0.198 10 false GND 1.042,3.906 1.5,4.104 0.458,0.198 10 false (A) 1.604,0.396 2.063,0.594 0.458,0.198 10 false I18 0.24,0.208 0.698,0.406 0.458,0.198 10 false *a 1.021,2.167 1.563,2.521 0.542,0.354 10 false +S
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal I18-9 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the I72 windshield wiper relay assembly connector and I18 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I72-24 (SPD) - I18-9 (+S) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - JUNCTION CONNECTOR)
3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the I72 windshield wiper relay assembly connector and I124 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I72-24 (SPD) - I124-20 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR