Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM2040EQ _59 Vehicle Exterior _014737 WIPER / WASHER _0075172 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Rain Sensor Circuit  


DESCRIPTION

The windshield wiper relay assembly receives a signal from the rain sensor to control the auto wiper system.

WIRING DIAGRAM

E226326
4.938,2.583 5.375,2.76 0.438,0.177 10 false I72 4.938,2.75 7.073,2.938 2.135,0.188 10 false Windshield Wiper Relay Assembly 2.885,2.625 3.25,2.802 0.365,0.177 10 false S1 2.885,2.802 3.708,2.99 0.823,0.188 10 false Rain Sensor 3.792,1.313 3.99,1.479 0.198,0.167 10 false 1 2.969,2.031 3.219,2.198 0.25,0.167 10 false ES 3.365,1.438 3.688,1.604 0.323,0.167 10 false MPX 2.958,0.875 3.26,1.042 0.302,0.167 10 false SIG 0.281,0.854 1.292,1.219 1.01,0.365 10 false from IG1 NO. 2 Relay 1.76,1.021 2.802,1.208 1.042,0.188 10 false ECU-IG1 NO. 2 5.406,1.438 5.885,1.604 0.479,0.167 10 false MPX1 5.146,1.313 5.344,1.479 0.198,0.167 10 false 14 2.771,0.781 2.906,0.948 0.135,0.167 10 false 4 2.771,1.938 2.906,2.104 0.135,0.167 10 false 2 0.885,3.271 2.51,3.458 1.625,0.188 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - RAIN SENSOR)
a.

Disconnect the I72 windshield wiper relay assembly connector.


b.

Disconnect the S1 rain sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I72-14 (MPX1) - S1-1 (MPX) Always Below 1 Ω
S1-1 (MPX) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT HARNESS AND CONNECTOR (RAIN SENSOR - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT HARNESS AND CONNECTOR (RAIN SENSOR - AUXILIARY BATTERY AND BODY GROUND)
a.
E169141
1.531,1.438 1.917,1.708 0.385,0.271 2.042,2.458 2.563,1.906 false 1.552,2.406 1.073,1.865 false 1.646,1.49 1.938,1.656 0.292,0.167 10 false S1 0.896,1.667 1.344,1.958 0.448,0.292 10 false ES 2.458,1.719 3,2.115 0.542,0.396 10 false SIG 0.375,0.344 0.74,0.604 0.365,0.26 10 false *a
*a Front view of wire harness connector (to Rain Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
S1-4 (SIG) - S1-2 (ES) Power switch on (IG) 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S1-2 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT RAIN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RAIN SENSOR
a.
E141656
0.563,1.615 0.969,1.875 0.406,0.26 1.979,1.979 2.292,1.563 false 1.688,1.417 1.813,1.979 false 0.313,0.229 0.74,0.708 0.427,0.479 10 false *a 2.198,1.375 2.635,1.531 0.438,0.156 10 false MPX 1.542,1.229 1.813,1.385 0.271,0.156 10 false ES 0.698,1.656 1,1.938 0.302,0.281 10 false S1
*a Component with harness connected
(Rain Sensor)


Reconnect the S1 rain sensor connector.


b.

Connect an oscilloscope to the rain sensor connector.


c.

Check for pulses.

OK:
Tester Connection Condition Specified Condition
S1-1 (MPX) - S1-2 (ES) Power switch on (IG) Pulse generation



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG