Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM2040EQ _59 Vehicle Exterior _014737 WIPER / WASHER _0075172 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Wiper ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to the windshield wiper relay assembly.

WIRING DIAGRAM

E196302
4.896,2.552 5.24,2.74 0.344,0.188 10 false I72 4.896,2.74 7.063,2.927 2.167,0.188 10 false Windshield Wiper Relay Assembly 0.594,0.927 2.01,1.115 1.417,0.188 10 false from IG1 NO. 1 Relay 5.448,0.917 5.75,1.115 0.302,0.198 10 false IG 5.448,2.146 5.667,2.344 0.219,0.198 10 false E 5.198,2.063 5.375,2.208 0.177,0.146 10 false 12 5.271,0.813 5.396,0.99 0.125,0.177 10 false 2 3.594,1.052 4.146,1.25 0.552,0.198 10 false WIPER 0.594,1.5 2.021,1.688 1.427,0.188 10 false from IG1 NO. 2 Relay 3.354,1.677 4.427,1.875 1.073,0.198 10 false ECU-IG1 NO. 2 5.469,1.521 5.792,1.719 0.323,0.198 10 false WIG 5.198,1.438 5.375,1.583 0.177,0.146 10 false 16

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.
E144475
1.5,1.042 1.958,1.344 0.458,0.302 2.708,2.188 2.99,2.646 false 1.156,2.427 1.156,2.896 false 0.74,2.802 1,2.198 false 1.646,1.104 2.01,1.271 0.365,0.167 10 false I72 0.323,0.292 0.594,0.438 0.271,0.146 10 false *a 2.979,2.667 3.188,2.833 0.208,0.167 10 false E 1.052,2.917 1.375,3.083 0.323,0.167 10 false WIG 0.615,2.823 0.802,2.99 0.188,0.167 10 false IG
*a Front view of wire harness connector
(to Windshield Wiper Relay Assembly)


Disconnect the I72 windshield wiper relay assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I72-2 (IG) - Body ground Power switch on (IG) 11 to 14 V
I72-16 (WIG) - Body ground Power switch on (IG) 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I72-12 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR