CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | Main body ECU (multiplex network body ECU) with 2 connectors | - | - |
| *1 | Main body ECU (multiplex network body ECU) | *2 | 2 connectors |
| *A | Main body ECU (multiplex network body ECU) with 3 connectors | - | - |
| *1 | Main body ECU (multiplex network body ECU) | *2 | 3 connectors |
Disconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3D-31 (BECU) - Body ground | V - Body ground | Battery power supply | Power switch off | 11 to 14 V |
| 3F-1 - Body ground | B - Body ground | Battery power supply | Power switch off | 11 to 14 V |
If the result is not as specified, there may be a malfunction in the wire harness.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3B-7 (GND1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| I12-3 (GND2) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3D-7 - Body ground | L - Body ground | Parking light RH drive output | Light control switch in tail or head position | 11 to 14 V |
| Light control switch off | Below 1 V | |||
| 3D-8 - Body ground | W - Body ground | Parking light LH drive output | Light control switch in tail or head position | 11 to 14 V |
| Light control switch off | Below 1 V | |||
| 3D-9 - Body ground | P - Body ground | Taillight relay drive signal output | Light control switch in tail or head position | 11 to 14 V |
| Light control switch off | Below 1 V | |||
| 3D-12 (HRLY) - Body ground | P - Body ground | Headlight relay drive output | Light control switch in head position | Below 1 V |
| Light control switch not in head position | 11 to 14 V | |||
| 3D-38 (FFGO)*1- Body ground | P - Body ground | Front fog light drive output | Light control switch in tail or head position, front fog light switch on | Below 1 V |
| Light control switch in tail or head position, front fog light switch off | 11 to 14 V | |||
| 3D-39 (DIM) - Body ground | W - Body ground | High beam headlight drive output | Dimmer switch in high or high flash position | Below 1 V |
| Dimmer switch in low position | 11 to 14 V | |||
| 3C-5 - Body ground | P - Body ground | Taillight relay drive signal output | Light control switch in tail or head position | 11 to 14 V |
| Light control switch off | Below 1 V | |||
| I13-5 (HU) - Body ground | LG - Body ground | Dimmer switch high position signal input | Dimmer switch in high position | Below 1 V |
| Dimmer switch not in high position | Pulse generation*2
11 to 14 V*3 |
|||
| I13-8 (HF) - Body ground | R - Body ground | Dimmer switch high flash position signal input | Dimmer switch in high flash position | Below 1 V |
| Dimmer switch not in high flash position | Pulse generation*2
11 to 14 V*3 |
|||
| I13-20 (CLTB) - I13-22 (CLTE) | B - P | Automatic light control sensor power supply output | Power switch off | Below 1 V |
| Power switch on (IG), light control switch in AUTO position | 11 to 14 V | |||
| I13-21 (CLTS) - Body ground | G - Body ground | Automatic light control sensor signal input | Power switch off | Below 1 V |
| Automatic light control system operates | Pulse generation
(See waveform 1) |
|||
| I13-27 (FFOG)*1 - Body ground | V - Body ground | Front fog light switch input | Front fog light switch on | Below 1 V |
| Front fog light switch off | Pulse generation*2
11 to 14 V*3 |
|||
| I13-28 (A) - Body ground | G - Body ground | Light control switch AUTO position signal input | Light control switch in AUTO position | Below 1 V |
| Light control switch not in AUTO position | Pulse generation | |||
| I13-29 (HEAD) - Body ground | P - Body ground | Light control switch head position input | Light control switch in head position | Below 1 V |
| Light control switch not in head position, power switch off | Pulse generation | |||
| I13-30 (TAIL) - Body ground | W - Body ground | Light control switch tail position signal input | Light control switch in tail or head position | Below 1 V |
| Light control switch in neither tail nor head position, power switch off | Pulse generation*2
11 to 14 V*3 |
*1: w/ Front Fog Light
*2: for main body ECU (multiplex network body ECU) with 3 connectors
*3: for main body ECU (multiplex network body ECU) with 2 connectors
If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.
Waveform 1
| Item | Content |
|---|---|
| Tool setting | 5 V/DIV., 5 ms./DIV. |
If the ambient light becomes brighter, width A becomes narrower.
CHECK POWER MANAGEMENT CONTROL ECU
Disconnect the A38 power management control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A38-15 (BL) - Body ground | W - Body ground | Back-up light signal | Power switch on (IG), shift lever not in R | Below 1 V |
| Power switch on (IG), shift lever in R | 11 to 14 V |