Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HIGH BEAM SYSTEM › 2012.02–2015.04
RM2040EQ _59 Vehicle Exterior _014738 LIGHTING (EXT) _0075174 AUTOMATIC HIGH BEAM SYSTEM U

LIGHTING (EXT)  AUTOMATIC HIGH BEAM SYSTEM  TERMINALS OF ECU  


CHECK AFS ECU (HEADLIGHT SWIVEL ECU ASSEMBLY)


E133226
3.422,0.374 3.708,0.521 0.286,0.147 10 A35 3.379,0.324 3.737,0.555 0.358,0.231

a.

Disconnect the A35 AFS ECU (headlight swivel ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A35-22 (E1) - Body ground W-B - Body ground AFS ECU (headlight swivel ECU assembly) ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A35-15 (IG) - Body ground LG - Body ground AFS ECU (headlight swivel ECU assembly) power supply Power switch off Below 1 V
Power switch on (IG) 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


d.

Reconnect the A35 AFS ECU (headlight swivel ECU assembly) connector.


e.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A35-11 (RHE) - A35-22 (E1) LG - W-B LIN communication Power switch off Below 1 V
Power switch on (IG) Pulse generation
A35-12 (MPX1) - A35-22 (E1) B - W-B CAN communication Power switch off Below 1 V
Power switch on (IG) Pulse generation
A35-13 (MPX2) - A35-22 (E1) W - W-B CAN communication Power switch off Below 1 V
Power switch on (IG) Pulse generation

If the result is not as specified, the AFS ECU (headlight swivel ECU assembly) may have a malfunction.



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


B278841
2.198,3.771 2.521,3.979 0.323,0.208 3.865,5.01 4.188,5.219 0.323,0.208 1.083,5.01 1.406,5.219 0.323,0.208 1.74,6.292 2.063,6.5 0.323,0.208 4.885,6.292 5.208,6.5 0.323,0.208 3.375,7.531 3.698,7.74 0.323,0.208 4.646,3.771 4.969,3.979 0.323,0.208 5.823,5.021 6.146,5.229 0.323,0.208 0.396,1.49 0.667,1.688 0.271,0.198 0.396,2 0.667,2.198 0.271,0.198 0.438,2.688 0.719,2.885 0.281,0.198 1.948,1.521 2.229,1.719 0.281,0.198 1.938,1.917 2.219,2.115 0.281,0.198 4.167,0.698 4.469,0.906 0.302,0.208 6.292,1.427 6.573,1.615 0.281,0.188 6.292,2.125 6.583,2.313 0.292,0.188 4.042,1.135 4.042,0.802 4.042,0.802 4.156,0.802 false 1.667,1.615 1.938,1.615 false 1.667,2.01 1.938,2.01 false 1.667,0.958 1.771,0.802 1.771,0.802 1.917,0.802 false 0.667,1.583 0.865,1.583 false 0.667,2.094 0.865,2.094 false 0.719,2.781 1.031,2.781 false 6.063,1.521 6.292,1.521 false 6.063,2.219 6.292,2.219 false 1.49,3.208 1.49,1.521 1.49,1.521 1.563,1.521 false 1.49,1.906 1.563,1.906 false 4.219,0.708 4.51,0.917 0.292,0.208 10 false MB 3.438,7.552 3.729,7.802 0.292,0.25 10 false MB 0.51,2.698 0.813,2.885 0.302,0.188 10 false 3F 0.458,1.5 0.76,1.719 0.302,0.219 10 false 3C 1.156,5.031 1.458,5.219 0.302,0.188 10 false 3C 6.354,1.438 6.625,1.615 0.271,0.177 10 false 3B 1.823,6.313 2.083,6.573 0.26,0.26 10 false 3B 6.365,2.135 6.615,2.313 0.25,0.177 10 false 3A 4.969,6.313 5.281,6.594 0.313,0.281 10 false 3A 0.458,2.01 0.75,2.198 0.292,0.188 10 false 3D 3.948,5.021 4.188,5.26 0.24,0.24 10 false 3D 2.01,1.531 2.375,1.729 0.365,0.198 10 false I13 4.719,3.792 5.021,3.99 0.302,0.198 10 false I13 2,1.927 2.354,2.146 0.354,0.219 10 false I12 2.271,3.792 2.5,3.958 0.229,0.167 10 false I12 5.906,5.042 6.104,5.24 0.198,0.198 10 false 3F 1.969,0.688 2.281,0.885 0.313,0.198 10 false *1 1.417,3.25 1.729,3.448 0.313,0.198 10 false *2 0.219,0.219 0.594,0.458 0.375,0.24 10 false *A
*A Main body ECU (multiplex network body ECU) with 2 connectors - -
*1 Main body ECU (multiplex network body ECU) *2 2 connectors


B282096
2.302,3.771 2.625,3.979 0.323,0.208 6.313,2.083 6.635,2.292 0.323,0.208 2.063,1.958 2.385,2.167 0.323,0.208 2.063,1.615 2.385,1.823 0.323,0.208 0.292,2.063 0.615,2.271 0.323,0.208 0.396,2.677 0.719,2.885 0.323,0.208 0.281,1.438 0.604,1.646 0.323,0.208 6.313,1.521 6.635,1.729 0.323,0.208 3.979,5.031 4.302,5.24 0.323,0.208 1.198,5.01 1.521,5.219 0.323,0.208 1.854,6.292 2.177,6.5 0.323,0.208 5.01,6.292 5.333,6.5 0.323,0.208 3.5,7.542 3.823,7.75 0.323,0.208 4.76,3.771 5.083,3.979 0.323,0.208 5.906,5.052 6.229,5.26 0.323,0.208 4.167,0.75 4.49,0.958 0.323,0.208 4.052,1.135 4.052,0.854 4.052,0.854 4.167,0.854 false 6.052,1.615 6.302,1.615 false 6.063,2.188 6.313,2.188 false 1.813,2.063 2.063,2.063 false 1.823,1.719 2.073,1.719 false 0.604,2.167 0.865,2.167 false 0.719,2.771 1.031,2.771 false 0.604,1.542 0.865,1.542 false 1.771,0.979 2,0.708 2,0.708 2.208,0.708 false 1.604,3.083 1.604,1.479 1.604,1.479 1.708,1.479 false 1.604,1.844 1.698,1.844 false 1.604,2.188 1.708,2.188 false 3.552,7.552 4.031,7.844 0.479,0.292 10 false MB 1.271,5.021 1.906,5.271 0.635,0.25 10 false 3C 1.938,6.313 2.51,6.667 0.573,0.354 10 false 3B 5.083,6.313 5.552,6.625 0.469,0.313 10 false 3A 4.052,5.052 4.615,5.365 0.563,0.313 10 false 3D 4.833,3.792 5.25,4.063 0.417,0.271 10 false I13 2.375,3.792 2.677,3.979 0.302,0.188 10 false I12 6.396,2.094 6.719,2.313 0.323,0.219 10 false 3A 2.135,1.969 2.583,2.25 0.448,0.281 10 false I12 2.135,1.635 2.5,1.865 0.365,0.229 10 false I13 0.385,2.083 0.865,2.385 0.479,0.302 10 false 3D 0.5,2.698 0.854,2.938 0.354,0.24 10 false 3F 0.354,1.458 0.833,1.74 0.479,0.281 10 false 3C 6.385,1.531 6.729,1.76 0.344,0.229 10 false 3B 5.99,5.073 6.302,5.333 0.313,0.26 10 false 3F 4.229,0.771 4.615,1 0.385,0.229 10 false MB 0.25,0.188 0.5,0.396 0.25,0.208 10 false *A 2.26,0.646 2.51,0.854 0.25,0.208 10 false *1 1.656,3.094 1.906,3.302 0.25,0.208 10 false *2
*A Main body ECU (multiplex network body ECU) with 3 connectors - -
*1 Main body ECU (multiplex network body ECU) *2 3 connectors


a.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
3D-39 (DIM) - Body ground W - Body ground High beam headlight drive output Dimmer switch in high or high flash position Below 1 V
Dimmer switch in low position 11 to 14 V
I13-5 (HU) - Body ground LG - Body ground Dimmer switch high position signal input Dimmer switch in high position Below 1 V
Dimmer switch not in high position Pulse generation*1
11 to 14 V*2
I13-20 (CLTB) - I13-22 (CLTE) B - P Automatic light control sensor power supply output Power switch off Below 1 V
Power switch on (IG), light control switch in AUTO position 11 to 14 V
I13-21 (CLTS) - Body ground G - Body ground Automatic light control sensor signal input Power switch off Below 1 V
Automatic light control system operates Pulse generation
(See waveform 1)
I13-28 (A) - Body ground G - Body ground Light control switch AUTO position signal input Light control switch in AUTO position Below 1 V
Light control switch not in AUTO position Pulse generation

*1: for main body ECU (multiplex network body ECU) with 3 connectors

*2: for main body ECU (multiplex network body ECU) with 2 connectors


If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.

i.
B113714
2.948,1.063 3.292,1.219 0.344,0.156 10 GND 1.844,1.177 1.969,1.333 0.125,0.156 10 A

Waveform 1

Item Content
Tool setting 5 V/DIV., 5 ms./DIV.

HINT:

If the ambient light becomes brighter, width A becomes narrower.





CHECK INNER REAR VIEW MIRROR ASSEMBLY


E233259
3.489,0.221 3.826,0.42 0.338,0.199 3.571,0.247 3.79,0.41 0.219,0.163 10 S2

a.

Disconnect the S2 inner rear view mirror assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S2-1 (E) - Body ground W-B - Body ground Inner rear view mirror assembly ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S2-4 (IG) - Body ground GR - Body ground Inner rear view mirror assembly power supply Power switch off Below 1 V
Power switch on (IG) 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


d.

Reconnect the S2 inner rear view mirror assembly connector.


e.

Measure the voltage or check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S2-5 (LIN) - S2-1 (E) LG - W-B LIN communication Power switch off Below 1 V
Automatic high beam system operating Pulse generation
(See waveform 1)

If the result is not as specified, the inner rear view mirror assembly may have a malfunction.

i.
E177995
2.857,1.753 3.208,1.909 0.351,0.156 10 GND

Waveform 1

Item Content
Tool setting 2 V/DIV., 20 ms./DIV.