Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2012.02–2015.04
RM2040EQ _51 Engine / Hybrid System _014700 CRUISE CONTROL _0074941 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the system to enter self-diagnostic mode. If a malfunction is present, cruise control indicator will blink.

HINT:

When a particular warning light remains blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in the relevant ECU is suspected.


WIRING DIAGRAM

E232249
5.042,3.281 7.083,3.729 2.042,0.448 10 false Power Management Control ECU 4.875,3.281 5.208,3.427 0.333,0.146 10 false I3 5.563,1.021 5.76,1.198 0.198,0.177 10 false 11 5.833,1.115 6.052,1.271 0.219,0.156 10 false TC 1.052,3.26 1.438,3.406 0.385,0.146 10 false DLC3 0.76,3.26 1.042,3.406 0.281,0.146 10 false I39 1.271,1.125 1.49,1.271 0.219,0.146 10 false TC 1.26,2.25 1.49,2.396 0.229,0.146 10 false CG 1.552,1.021 1.74,1.167 0.188,0.146 10 false 13 1.594,2.146 1.688,2.292 0.094,0.146 10 false 4

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
I3-11 (TC) - I39-13 (TC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TERMINAL CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DLC3 - POWER MANAGEMENT CONTROL ECU)

2.CHECK HARNESS AND CONNECTOR (TERMINAL CG of DLC3 - BODY GROUND)
a.
E265513C01
1.5,0.417 1.75,0.583 0.25,0.167 0.917,0.479 1.583,1.063 false 0.073,0.063 0.385,0.219 0.313,0.156 10 *a 1.542,0.417 2,0.615 0.458,0.198 10 I39 0.688,0.396 1,0.594 0.313,0.198 10 CG
*a DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
I39-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - BODY GROUND)
a.
E265513C02
1.5,0.417 1.75,0.583 0.25,0.167 2.406,1.958 1.771,1.625 false 0.073,0.063 0.385,0.219 0.313,0.156 10 *a 1.542,0.417 2,0.615 0.458,0.198 10 I39 2.458,1.885 2.771,2.083 0.313,0.198 10 TC
*a DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
I39-13 (TC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR