Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Memory)
RM2040EQ _59 Vehicle Exterior _014736 MIRROR (EXT) _0075158 POWER MIRROR CONTROL SYSTEM(w/ Memory) U

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  DATA LIST / ACTIVE TEST  


USING INTELLIGENT TESTER


a.

Connect the intelligent tester to the DLC3.


b.

Monitor the ECU data by following the prompts on the intelligent tester screen.

HINT:

The intelligent tester has a "Snapshot" function which records the monitored data. Refer to the intelligent tester operator's manual for further details.




DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Mirror L or Mirror R / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Mirror L > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory Switch1 Seat memory switch M1 signal ON or OFF ON: Seat memory switch M1 on
OFF: Seat memory switch M1 off
-
Seat Memory Switch2 Seat memory switch M2 signal ON or OFF ON: Seat memory switch M2 on
OFF: Seat memory switch M2 off
-
Seat Memory Switch3 Seat memory switch M3 signal* ON or OFF ON: Seat memory switch M3 on
OFF: Seat memory switch M3 off
Not applicable
Seat Memory Set SW Seat memory switch SET signal ON or OFF ON: Seat memory switch SET on
OFF: Seat memory switch SET off
-
Mirror Memory No.1 Mirror position memorized in memory switch M1 ON or OFF ON: Memorized
OFF: Not memorized
-
Mirror Memory No.2 Mirror position memorized in memory switch M2 ON or OFF ON: Memorized
OFF: Not memorized
-
Mirror Memory No.3 Mirror position memorized in memory switch M3* ON or OFF ON: Memorized
OFF: Not memorized
Not applicable
Mirror Vertical Sensor Vol Vertical mirror position MIN: 0, MAX: 4.98 V Within range from 0 to 4.98 V -
Mirror Horizontal Sensor Vol Horizontal mirror position MIN: 0, MAX: 4.98 V Within range from 0 to 4.98 V -
+B Voltage Input Value Power supply for outer mirror control ECU assembly MIN: 0 V, MAX: 19.98 V Within range from 11 to 14 V -

*: Although the item is displayed on the intelligent tester, it is not applicable to this vehicle.


Body Electrical > Mirror R > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory Switch1 Seat memory switch M1 signal ON or OFF ON: Seat memory switch M1 on
OFF: Seat memory switch M1 off
-
Seat Memory Switch2 Seat memory switch M2 signal ON or OFF ON: Seat memory switch M2 on
OFF: Seat memory switch M2 off
-
Seat Memory Switch3 Seat memory switch M3 signal* ON or OFF ON: Seat memory switch M3 on
OFF: Seat memory switch M3 off
Not applicable
Seat Memory Set SW Seat memory switch SET signal ON or OFF ON: Seat memory switch SET on
OFF: Seat memory switch SET off
-
Mirror Memory No.1 Mirror position memorized in memory switch M1 ON or OFF ON: Memorized
OFF: Not memorized
-
Mirror Memory No.2 Mirror position memorized in memory switch M2 ON or OFF ON: Memorized
OFF: Not memorized
-
Mirror Memory No.3 Mirror position memorized in memory switch M3* ON or OFF ON: Memorized
OFF: Not memorized
Not applicable
Mirror Vertical Sensor Vol Vertical mirror position MIN: 0, MAX: 4.98 V Within range from 0 to 4.98 V -
Mirror Horizontal Sensor Vol Horizontal mirror position MIN: 0, MAX: 4.98 V Within range from 0 to 4.98 V -
+B Voltage Input Value Power supply for outer mirror control ECU assembly MIN: 0 V, MAX: 19.98 V Within range from 11 to 14 V -

*: Although the item is displayed on the intelligent tester, it is not applicable to this vehicle.



f.

Enter the following menus: Body / Main Body / Data List.


g.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Lock SW-Lock Door control switch (power window regulator master switch assembly) lock signal ON or OFF ON: Lock side of door control switch (power window regulator master switch assembly) pushed
OFF: Lock side of door control switch (power window regulator master switch assembly) not pushed
-
Door Lock SW-Unlock Door control switch (power window regulator master switch assembly) unlock signal ON or OFF ON: Unlock side of door control switch (power window regulator master switch assembly) pushed
OFF: Unlock side of door control switch (power window regulator master switch assembly) not pushed
-
FR Door Courtesy SW Driver door courtesy switch condition ON or OFF ON: Door courtesy switch on (driver door open)
OFF: Door courtesy switch off (driver door closed)
-
Mirror Selection SW (R) Mirror select switch signal for RH mirror ON or OFF ON: Mirror select switch in R position
OFF: Mirror select switch off or in L position
-
Mirror Selection SW (L) Mirror select switch signal for LH mirror ON or OFF ON: Mirror select switch in L position
OFF: Mirror select switch off or in R position
-
Mirror Position SW (R) Mirror adjust switch signal (Right) ON or OFF ON: Mirror adjust switch pressed right
OFF: Mirror adjust switch not pressed right
Check with the mirror select switch in any position except neutral
Mirror Position SW (L) Mirror adjust switch signal (Left) ON or OFF ON: Mirror adjust switch pressed left
OFF: Mirror adjust switch not pressed left
Check with the mirror select switch in any position except neutral
Mirror Position SW (Up) Mirror adjust switch signal (Up) ON or OFF ON: Mirror adjust switch pressed up
OFF: Mirror adjust switch not pressed up
Check with the mirror select switch in any position except neutral
Mirror Position SW (Dwn) Mirror adjust switch signal (Down) ON or OFF ON: Mirror adjust switch pressed down
OFF: Mirror adjust switch not pressed down
Check with the mirror select switch in any position except neutral
Mem SW No. w/KeyID1 Switch linked with key ID1 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID1
MEM SW1: M1 linked with key ID1
MEM SW2: M2 linked with key ID1
MEM SW3: M3 linked with key ID1*
-
Mem SW No. w/KeyID2 Switch linked with key ID2 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID2
MEM SW1: M1 linked with key ID2
MEM SW2: M2 linked with key ID2
MEM SW3: M3 linked with key ID2*
-
Mem SW No. w/KeyID3 Switch linked with key ID3 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID3
MEM SW1: M1 linked with key ID3
MEM SW2: M2 linked with key ID3
MEM SW3: M3 linked with key ID3*
-
Mem SW No. w/KeyID4 Switch linked with key ID4 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID4
MEM SW1: M1 linked with key ID4
MEM SW2: M2 linked with key ID4
MEM SW3: M3 linked with key ID4*
-
Mem SW No. w/KeyID5 Switch linked with key ID5 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID5
MEM SW1: M1 linked with key ID5
MEM SW2: M2 linked with key ID5
MEM SW3: M3 linked with key ID5*
-
Mem SW No. w/KeyID6 Switch linked with key ID6 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID6
MEM SW1: M1 linked with key ID6
MEM SW2: M2 linked with key ID6
MEM SW3: M3 linked with key ID6*
-
Mem SW No. w/KeyID7 Switch linked with key ID7 NONE, MEM SW1, MEM SW2, or MEM SW3* NONE: No switches linked with key ID7
MEM SW1: M1 linked with key ID7
MEM SW2: M2 linked with key ID7
MEM SW3: M3 linked with key ID7*
-

*: Although the item is displayed on the intelligent tester, it is not applicable to this vehicle.




ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Mirror L or Mirror R / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Mirror L > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Mirror Up/Down Mirror vertical operation Up / Down
·

Operate with power switch on (IG) and the vehicle stopped.

·

This test activates the mirror up or down.

·

This operation can be confirmed by watching the mirror move in the desired direction.


Mirror Right/Left Mirror horizontal operation Right / Left
·

Operate with power switch on (IG) and the vehicle stopped.

·

This test tilts the mirror right or left.

·

This operation can be confirmed by watching the mirror move in the desired direction.


Body Electrical > Mirror R > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Mirror Up/Down Mirror vertical operation Up / Down
·

Operate with power switch on (IG) and the vehicle stopped.

·

This test activates the mirror up or down.

·

This operation can be confirmed by watching the mirror move in the desired direction.


Mirror Right/Left Mirror horizontal operation Right / Left
·

Operate with power switch on (IG) and the vehicle stopped.

·

This test tilts the mirror right or left.

·

This operation can be confirmed by watching the mirror move in the desired direction.



f.

Enter the following menus: Body / Driver Seat / Active Test.


g.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Buzzer Buzzer built into the position control ECU and switch assembly ON or OFF -