Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2040EQ _58 Vehicle Interior _014727 SUPPLEMENTAL RESTRAINT SYSTEMS _0075078 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1617/84  Lost Communication with Front Airbag Sensor LH  B1618/84  Front Airbag Sensor LH Initialization Incomplete  


DESCRIPTION

The front airbag sensor LH circuit consists of the airbag sensor assembly and front airbag sensor LH.

The front airbag sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbag and pretensioner should be deployed.

These DTCs are stored when a malfunction is detected in the front airbag sensor LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1617/84 Lost Communication with Front Airbag Sensor LH
·

The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor LH circuit.

·

Front airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor LH

·

Airbag sensor assembly


Does not apply to test/check mode
B1618/84 Front Airbag Sensor LH Initialization Incomplete
·

The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor LH circuit.

·

Front airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor LH

·

Airbag sensor assembly


Does not apply to test/check mode

WIRING DIAGRAM

C244889E11
3.458,0.906 3.927,1.5 0.469,0.594 10 IA5 3.51,0.719 3.865,1.146 0.354,0.427 10 3 3.458,2.083 3.885,2.542 0.427,0.458 10 IA5 3.51,1.896 3.844,2.333 0.333,0.438 10 4 5.135,0.813 5.573,1.406 0.438,0.594 10 30 5.135,1.99 5.51,2.49 0.375,0.5 10 28 5.396,0.896 5.885,1.385 0.49,0.49 10 +SL 5.396,2.073 5.885,2.531 0.49,0.458 10 -SL 1.854,0.813 2.25,1.49 0.396,0.677 10 2 1.854,1.99 2.188,2.594 0.333,0.604 10 1 1.479,0.896 2.01,1.469 0.531,0.573 10 +SL 1.51,2.073 1.948,2.563 0.438,0.49 10 -SL 0.438,2.927 0.938,3.26 0.5,0.333 10 A12 0.438,3.083 2.031,3.406 1.594,0.323 10 Front Airbag Sensor LH 5.219,2.927 5.604,3.385 0.385,0.458 10 I47 5.219,3.083 6.844,3.479 1.625,0.396 10 Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor LH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and front airbag sensor LH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN)

NG

REPLACE WIRE HARNESS

2.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN)
a.
C238389C01
0.771,0.5 1.115,0.729 0.344,0.229 0.583,3.583 0.927,3.833 0.344,0.25 1.969,0.781 1.792,0.99 false 2.146,0.781 2.354,1.01 false 1.323,3.729 1.115,4.135 false 1.542,3.719 1.74,4.135 false 2.052,1.031 2.052,1.229 false 0.833,2.229 1.188,2.677 0.354,0.448 10 F 1.073,2.229 1.396,2.677 0.323,0.448 10 E 1.417,2.229 1.76,2.698 0.344,0.469 10 D 1.583,2.229 1.844,2.646 0.26,0.417 10 C 1.927,2.229 2.313,2.635 0.385,0.406 10 B 2.167,2.229 2.49,2.604 0.323,0.375 10 A 0.448,2.219 0.958,2.719 0.51,0.5 10 *1 2.667,2.24 3.042,2.75 0.375,0.51 10 *2 0.604,0.167 0.854,0.427 0.25,0.26 10 *a 0.365,3.219 0.729,3.625 0.365,0.406 10 *b 0.865,0.542 1.25,0.906 0.385,0.365 10 I47 1.531,0.927 1.917,1.208 0.385,0.281 10 -SL 2.417,0.938 2.781,1.271 0.365,0.333 10 +SL 0.646,3.625 1.052,4.021 0.406,0.396 10 A12 0.969,4.146 1.333,4.469 0.365,0.323 10 -SL 1.635,4.146 2.021,4.448 0.385,0.302 10 +SL 1.99,1.26 2.229,1.583 0.24,0.323 10 *3
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Airbag Sensor LH)


Connect the connectors that link the engine room main wire and instrument panel wire.


b.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A12-2 (+SL) - A12-1 (-SL) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)

NG

10.CHECK INSTRUMENT PANEL WIRE (OPEN)
3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)
a.
C238385C04
0.406,2.292 0.771,2.531 0.365,0.24 1.125,2.448 0.938,2.865 false 1.344,2.448 1.542,2.885 false 0.844,0.917 1.177,1.365 0.333,0.448 10 F 1.083,0.927 1.385,1.25 0.302,0.323 10 E 1.417,0.927 1.688,1.333 0.271,0.406 10 D 1.583,0.938 1.896,1.417 0.313,0.479 10 C 1.927,0.927 2.25,1.438 0.323,0.51 10 B 2.167,0.927 2.448,1.344 0.281,0.417 10 A 0.458,0.927 0.813,1.344 0.354,0.417 10 *1 2.635,0.948 2.938,1.292 0.302,0.344 10 *2 0.354,1.896 0.708,2.25 0.354,0.354 10 *a 0.458,2.333 0.854,2.74 0.396,0.406 10 A12 0.771,2.885 1.125,3.177 0.354,0.292 10 -SL 1.448,2.896 1.813,3.177 0.365,0.281 10 +SL
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor LH)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A12-2 (+SL) - A12-1 (-SL) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)

NG

9.CHECK INSTRUMENT PANEL WIRE (SHORT)
4.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)
a.
C238385C04
0.406,2.292 0.771,2.531 0.365,0.24 1.125,2.448 0.938,2.865 false 1.344,2.448 1.542,2.885 false 0.844,0.917 1.177,1.365 0.333,0.448 10 F 1.083,0.927 1.385,1.25 0.302,0.323 10 E 1.417,0.927 1.688,1.333 0.271,0.406 10 D 1.583,0.938 1.896,1.417 0.313,0.479 10 C 1.927,0.927 2.25,1.438 0.323,0.51 10 B 2.167,0.927 2.448,1.344 0.281,0.417 10 A 0.458,0.927 0.813,1.344 0.354,0.417 10 *1 2.635,0.948 2.938,1.292 0.302,0.344 10 *2 0.354,1.896 0.708,2.25 0.354,0.354 10 *a 0.458,2.333 0.854,2.74 0.396,0.406 10 A12 0.771,2.885 1.125,3.177 0.354,0.292 10 -SL 1.448,2.896 1.813,3.177 0.365,0.281 10 +SL
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A12-2 (+SL) - Body ground Power switch on (IG) Below 1 V
A12-1 (-SL) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

5.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)

NG

8.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
5.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)
a.
C238385C04
0.406,2.292 0.771,2.531 0.365,0.24 1.125,2.448 0.938,2.865 false 1.344,2.448 1.542,2.885 false 0.844,0.917 1.177,1.365 0.333,0.448 10 F 1.083,0.927 1.385,1.25 0.302,0.323 10 E 1.417,0.927 1.688,1.333 0.271,0.406 10 D 1.583,0.938 1.896,1.417 0.313,0.479 10 C 1.927,0.927 2.25,1.438 0.323,0.51 10 B 2.167,0.927 2.448,1.344 0.281,0.417 10 A 0.458,0.927 0.813,1.344 0.354,0.417 10 *1 2.635,0.948 2.938,1.292 0.302,0.344 10 *2 0.354,1.896 0.708,2.25 0.354,0.354 10 *a 0.458,2.333 0.854,2.74 0.396,0.406 10 A12 0.771,2.885 1.125,3.177 0.354,0.292 10 -SL 1.448,2.896 1.813,3.177 0.365,0.281 10 +SL
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A12-2 (+SL) - Body ground Always 1 MΩ or higher
A12-1 (-SL) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK FRONT AIRBAG SENSOR LH

NG

7.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
6.CHECK FRONT AIRBAG SENSOR LH
a.
C238386C02
2.083,1.01 2.448,1.5 0.365,0.49 10 A 1.927,1.01 2.427,1.479 0.5,0.469 10 B 1.583,1.01 1.969,1.521 0.385,0.51 10 C 1.427,1.01 1.844,1.583 0.417,0.573 10 D 1.083,1.01 1.531,1.667 0.448,0.656 10 E 0.938,1.01 1.521,1.75 0.583,0.74 10 F 0.563,1.021 1.125,1.594 0.563,0.573 10 *1 2.542,1.031 2.885,1.563 0.344,0.531 10 *2
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the front airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1612/83, B1613/83, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTCs B1612/83, B1613/83, B1617/84 and B1618/84 are not output. A
DTC B1617/84 or B1618/84 is output. B
DTC B1612/83 or B1613/83 is output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the front airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C

7.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C238388C05
0.5,2.177 0.854,2.406 0.354,0.229 1.354,2.458 1.052,2.885 false 1.458,2.458 1.792,2.885 false 1.24,0.906 1.24,1.156 false 1.823,0.781 1.823,0.375 1.823,0.375 1.667,0.375 false 0.781,0.76 1.052,1.115 0.271,0.354 10 F 1.031,0.76 1.365,1.083 0.333,0.323 10 E 1.375,0.76 1.771,1.094 0.396,0.333 10 D 1.615,0.771 1.854,1.042 0.24,0.271 10 C 1.958,0.76 2.219,1.135 0.26,0.375 10 B 2.208,0.76 2.479,1.104 0.271,0.344 10 A 0.396,0.76 0.75,1.135 0.354,0.375 10 *1 2.667,0.771 2.969,1.146 0.302,0.375 10 *2 1.5,0.302 1.844,0.719 0.344,0.417 10 *4 1.167,1.188 1.469,1.5 0.302,0.313 10 *3 0.385,1.75 0.656,2.052 0.271,0.302 10 *a 0.583,2.219 0.99,2.615 0.406,0.396 10 IA5 0.885,2.906 1.292,3.208 0.406,0.302 10 +SL 1.729,2.906 2.083,3.125 0.354,0.219 10 -SL
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IA5-3 (+SL) - Body ground Always 1 MΩ or higher
IA5-4 (-SL) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

8.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C238388C05
0.5,2.177 0.854,2.406 0.354,0.229 1.354,2.458 1.052,2.885 false 1.458,2.458 1.792,2.885 false 1.24,0.906 1.24,1.156 false 1.823,0.781 1.823,0.375 1.823,0.375 1.667,0.375 false 0.781,0.76 1.052,1.115 0.271,0.354 10 F 1.031,0.76 1.365,1.083 0.333,0.323 10 E 1.375,0.76 1.771,1.094 0.396,0.333 10 D 1.615,0.771 1.854,1.042 0.24,0.271 10 C 1.958,0.76 2.219,1.135 0.26,0.375 10 B 2.208,0.76 2.479,1.104 0.271,0.344 10 A 0.396,0.76 0.75,1.135 0.354,0.375 10 *1 2.667,0.771 2.969,1.146 0.302,0.375 10 *2 1.5,0.302 1.844,0.719 0.344,0.417 10 *4 1.167,1.188 1.469,1.5 0.302,0.313 10 *3 0.385,1.75 0.656,2.052 0.271,0.302 10 *a 0.583,2.219 0.99,2.615 0.406,0.396 10 IA5 0.885,2.906 1.292,3.208 0.406,0.302 10 +SL 1.729,2.906 2.083,3.125 0.354,0.219 10 -SL
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
IA5-3 (+SL) - Body ground Power switch on (IG) Below 1 V
IA5-4 (-SL) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

9.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C238388C05
0.5,2.177 0.854,2.406 0.354,0.229 1.354,2.458 1.052,2.885 false 1.458,2.458 1.792,2.885 false 1.24,0.906 1.24,1.156 false 1.823,0.781 1.823,0.375 1.823,0.375 1.667,0.375 false 0.781,0.76 1.052,1.115 0.271,0.354 10 F 1.031,0.76 1.365,1.083 0.333,0.323 10 E 1.375,0.76 1.771,1.094 0.396,0.333 10 D 1.615,0.771 1.854,1.042 0.24,0.271 10 C 1.958,0.76 2.219,1.135 0.26,0.375 10 B 2.208,0.76 2.479,1.104 0.271,0.344 10 A 0.396,0.76 0.75,1.135 0.354,0.375 10 *1 2.667,0.771 2.969,1.146 0.302,0.375 10 *2 1.5,0.302 1.844,0.719 0.344,0.417 10 *4 1.167,1.188 1.469,1.5 0.302,0.313 10 *3 0.385,1.75 0.656,2.052 0.271,0.302 10 *a 0.583,2.219 0.99,2.615 0.406,0.396 10 IA5 0.885,2.906 1.292,3.208 0.406,0.302 10 +SL 1.729,2.906 2.083,3.125 0.354,0.219 10 -SL
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IA5-3 (+SL) - IA5-4 (-SL) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
C238390C01
0.813,0.521 1.125,0.729 0.313,0.208 0.563,3.646 0.896,3.865 0.333,0.219 2.01,0.823 1.833,1.031 false 2.177,0.833 2.385,1.063 false 1.427,3.927 1.188,4.188 false 1.531,3.927 1.844,4.188 false 1.24,2.375 1.24,2.667 false 1.833,2.24 1.833,1.896 1.833,1.896 1.688,1.896 false 2.094,1.083 2.094,1.271 false 0.781,2.229 1.052,2.615 0.271,0.385 10 F 1.021,2.24 1.323,2.583 0.302,0.344 10 E 1.375,2.229 1.635,2.552 0.26,0.323 10 D 1.615,2.24 1.865,2.646 0.25,0.406 10 C 1.958,2.229 2.24,2.688 0.281,0.458 10 B 2.208,2.229 2.521,2.635 0.313,0.406 10 A 1.531,1.823 1.813,2.104 0.281,0.281 10 *4 0.885,0.542 1.281,0.917 0.396,0.375 10 I47 1.594,0.969 1.917,1.26 0.323,0.292 10 -SL 2.438,0.979 2.771,1.292 0.333,0.313 10 +SL 0.635,3.677 0.958,3.979 0.323,0.302 10 IA5 1.792,4.198 2.167,4.438 0.375,0.24 10 -SL 1,4.198 1.375,4.479 0.375,0.281 10 +SL 2.698,2.229 2.969,2.656 0.271,0.427 10 *2 1.177,2.688 1.448,2.948 0.271,0.26 10 *3 0.406,2.229 0.76,2.573 0.354,0.344 10 *1 0.635,0.188 0.896,0.49 0.26,0.302 10 *a 0.375,3.229 0.76,3.583 0.385,0.354 10 *b 2.031,1.292 2.406,1.646 0.375,0.354 10 *5
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IA5-3 (+SL) - IA5-4 (-SL) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE