Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2040EQ _58 Vehicle Interior _014727 SUPPLEMENTAL RESTRAINT SYSTEMS _0075078 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1860/64  Short in Driver Side Knee Airbag Squib Circuit  B1861/64  Open in Driver Side Knee Airbag Squib Circuit  B1862/64  Short to GND in Driver Side Knee Airbag Squib Circuit  B1863/64  Short to B+ in Driver Side Knee Airbag Squib Circuit  


DESCRIPTION

The driver side knee airbag squib circuit consists of the airbag sensor assembly and lower No. 1 instrument panel airbag assembly.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side knee airbag squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1860/64 Short in Driver Side Knee Airbag Squib Circuit
·

The airbag sensor assembly receives a line short circuit signal in the driver side knee airbag squib during primary check.

·

Driver side knee airbag squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Lower No. 1 instrument panel airbag assembly (Driver side knee airbag squib)

·

Airbag sensor assembly


Applies to check mode
B1861/64 Open in Driver Side Knee Airbag Squib Circuit
·

The airbag sensor assembly receives an open circuit signal in the driver side knee airbag squib.

·

Driver side knee airbag squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Lower No. 1 instrument panel airbag assembly (Driver side knee airbag squib)

·

Airbag sensor assembly


Applies to check mode
B1862/64 Short to GND in Driver Side Knee Airbag Squib Circuit
·

The airbag sensor assembly receives a short circuit to ground signal in the driver side knee airbag squib.

·

Driver side knee airbag squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Lower No. 1 instrument panel airbag assembly (Driver side knee airbag squib)

·

Airbag sensor assembly


Applies to check mode
B1863/64 Short to B+ in Driver Side Knee Airbag Squib Circuit
·

The airbag sensor assembly receives a short circuit to B+ signal in the driver side knee airbag squib.

·

Driver side knee airbag squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Lower No. 1 instrument panel airbag assembly (Driver side knee airbag squib)

·

Airbag sensor assembly


Applies to check mode

WIRING DIAGRAM

C249389E30
0.698,2.5 1.115,2.802 0.417,0.302 10 I40 0.698,2.667 3.604,3.5 2.906,0.833 10 Lower No. 1 Instrument Panel Airbag Assembly (Driver Side Knee Airbag Squib) 4.646,3.01 5.146,3.271 0.5,0.26 10 I47 4.698,1.99 5.083,2.333 0.385,0.344 10 DK- 4.458,1.896 4.833,2.313 0.375,0.417 10 10 4.688,1.146 5.25,1.5 0.563,0.354 10 DK+ 2.073,1.906 2.646,2.292 0.573,0.385 10 DK- 2.052,1.063 2.615,1.469 0.563,0.406 10 DK+ 4.51,1.052 4.844,1.521 0.333,0.469 10 9 2.406,1.906 2.844,2.313 0.438,0.406 10 2 2.406,1.063 2.792,1.521 0.385,0.458 10 1 4.646,3.188 6.5,3.531 1.854,0.344 10 Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C239229C01
0.552,1.115 0.552,1.542 false 1.313,0.979 1.313,0.604 1.313,0.604 1.146,0.604 false 0.469,1.573 0.958,1.958 0.49,0.385 10 *1 0.979,0.531 1.313,0.854 0.333,0.323 10 *3 2.313,0.969 2.625,1.344 0.313,0.375 10 *2 1.865,0.969 2.188,1.427 0.323,0.458 10 A 1.5,0.969 1.802,1.406 0.302,0.438 10 B 1.021,0.969 1.396,1.417 0.375,0.448 10 C 0.656,0.969 1.146,1.531 0.49,0.563 10 D
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the lower No. 1 instrument panel airbag assembly and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the lower No. 1 instrument panel airbag assembly and airbag sensor assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the instrument panel wire connector (on the lower No. 1 instrument panel airbag assembly side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short spring for the instrument panel wire with the activation prevention mechanism are not deformed or damaged.

OK:

The short spring is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (DRIVER SIDE KNEE AIRBAG SQUIB)

NG

REPLACE INSTRUMENT PANEL WIRE

2.CHECK LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (DRIVER SIDE KNEE AIRBAG SQUIB)
a.
C238357C01
0.406,2.271 0.75,2.531 0.344,0.26 0.698,0.938 0.698,1.333 false 1.802,2.365 1.979,2.365 false 0.635,1.344 1.052,1.729 0.417,0.385 10 *1 2.24,0.802 2.635,1.26 0.396,0.458 10 *2 1.823,0.781 2.219,1.292 0.396,0.51 10 A 1.677,0.781 2.104,1.198 0.427,0.417 10 B 1.167,0.802 1.75,1.354 0.583,0.552 10 C 0.823,0.792 1.198,1.271 0.375,0.479 10 D 0.49,2.323 0.927,2.76 0.438,0.438 10 I40 2.021,2.292 2.49,2.615 0.469,0.323 10 SST 0.344,1.771 0.583,2.094 0.24,0.323 10 *a
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Lower No. 1 Instrument Panel Airbag Assembly)


Connect the connector to the airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the lower No. 1 instrument panel airbag assembly (driver side knee airbag squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1860/64, B1861/64, B1862/64 or B1863/64 is not output.


HINT:

Codes other than DTCs B1860/64, B1861/64, B1862/64 and B1863/64 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.


Result:
Proceed to
OK
NG



OK

REPLACE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

NG

3.CHECK INSTRUMENT PANEL WIRE
3.CHECK INSTRUMENT PANEL WIRE
a.
C237236C09
0.542,2.406 0.896,2.646 0.354,0.24 0.688,0.906 0.688,1.302 false 1.604,2.26 1.875,2.26 false 1.146,2.25 1.417,2.25 false 1.385,0.76 1.385,0.302 1.385,0.302 1.094,0.302 false 0.625,1.313 0.865,1.542 0.24,0.229 10 *1 2.292,0.75 2.729,1.042 0.438,0.292 10 *2 1.885,0.74 2.26,1.125 0.375,0.385 10 A 1.583,0.74 1.99,1.25 0.406,0.51 10 B 1.135,0.75 1.552,1.25 0.417,0.5 10 C 0.823,0.75 1.229,1.281 0.406,0.531 10 D 0.635,2.448 1.042,2.854 0.406,0.406 10 I40 1.917,2.188 2.375,2.615 0.458,0.427 10 DK- 0.833,2.177 1.26,2.531 0.427,0.354 10 DK+ 0.24,1.802 0.573,2.073 0.333,0.271 10 *a 0.938,0.229 1.365,0.563 0.427,0.333 10 *3
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Lower No. 1 Instrument Panel Airbag Assembly)


Disconnect the instrument panel wire from the airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I40-1 (DK+) - Body ground Power switch on (IG) Below 1 V
I40-2 (DK-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I40-1 (DK+) - I40-2 (DK-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I40-1 (DK+) - Body ground Always 1 MΩ or higher
I40-2 (DK-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I40-1 (DK+) - I40-2 (DK-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK DTC
a.
C238245C01
0.844,1.146 0.844,1.458 false 0.969,1 1.219,1.385 0.25,0.385 10 false D 1.125,1 1.333,1.417 0.208,0.417 10 false C 1.583,1 1.823,1.354 0.24,0.354 10 false B 1.74,1 2,1.323 0.26,0.323 10 false A 2.167,0.99 2.458,1.313 0.292,0.323 10 false *2 0.76,1.479 1.083,1.781 0.323,0.302 10 false *1
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag Sensor Assembly


Connect the connectors to the lower No. 1 instrument panel airbag assembly and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1860/64, B1861/64, B1862/64 or B1863/64 is not output.


HINT:

Codes other than DTCs B1860/64, B1861/64, B1862/64 and B1863/64 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG