Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2012.02–2015.04
RM2040EQ _58 Vehicle Interior _014727 SUPPLEMENTAL RESTRAINT SYSTEMS _0075078 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are displayed by blinking of the SRS warning light.

HINT:
·

When multiple warning lights in the combination meter blink continuously, a ground short in the wiring or an ECU connected to terminal TC of the DLC3 is suspected.

·

A DTC output mode signal is transmitted through the CAN communication system to each ECU including the airbag sensor assembly. Thus when multiple systems do not enter DTC output mode, there may be a power management control ECU malfunction.



WIRING DIAGRAM

C241762E11
1.542,1.083 2.219,1.406 0.677,0.323 10 false CA1H 1.552,1.792 2.083,2.083 0.531,0.292 10 false CA1L 5.76,1.083 6.313,1.479 0.552,0.396 10 false CANH 5.76,1.792 6.25,2.188 0.49,0.396 10 false CANL 1.719,2.5 2.156,2.906 0.438,0.406 10 false TC 0.552,3.094 2.688,3.427 2.135,0.333 10 false Power Management Control ECU 2.094,1.094 2.438,1.469 0.344,0.375 10 false I4 2.073,0.854 2.531,1.271 0.458,0.417 10 false 25 2.063,1.552 2.458,1.875 0.396,0.323 10 false 24 2.063,2.281 2.292,2.552 0.229,0.271 10 false 11 5.521,1.656 5.969,2.156 0.448,0.5 10 false 22 5.521,0.948 5.906,1.458 0.385,0.51 10 false 13 0.865,5.469 2.635,5.698 1.771,0.229 10 false : CAN Communication Line 1.229,4.115 1.573,4.406 0.344,0.292 10 false CG 1.729,4.104 2.333,4.417 0.604,0.313 10 false TC 1.99,4.01 2.333,4.438 0.344,0.427 10 false 13 1.031,4 1.323,4.333 0.292,0.333 10 false 4 1.198,4.583 1.635,4.865 0.438,0.281 10 false I39 1.198,4.74 1.813,5.094 0.615,0.354 10 false DLC3 5.448,4.948 5.99,5.458 0.542,0.51 10 false I47 5.448,5.104 7.01,5.552 1.563,0.448 10 false Airbag Sensor Assembly 2.094,1.792 2.365,2.073 0.271,0.281 10 false I4 2.094,2.5 2.406,2.781 0.313,0.281 10 false I3

PROCEDURE

1.CHECK WIRE HARNESS (TC OF DLC3 - TC OF POWER MANAGEMENT CONTROL ECU)
a.
C234357C02
0.24,1.188 0.594,1.438 0.354,0.25 0.323,3.479 0.656,3.719 0.333,0.24 1.792,1.625 2.115,2.021 false 1.729,3.719 1.51,4.333 false 0.229,0.188 0.448,0.375 0.219,0.188 10 false *1 0.333,1.229 0.677,1.5 0.344,0.271 10 false I39 2.042,2.073 2.271,2.219 0.229,0.146 10 false TC 0.26,2.51 0.479,2.698 0.219,0.188 10 false *a 0.458,3.521 0.75,3.813 0.292,0.292 10 false I3 1.406,4.375 1.677,4.521 0.271,0.146 10 false TC
*1 DLC3
*a Front view of wire harness connector
(to Power Management Control ECU)


Turn the power switch off.


b.

Disconnect the connector from the power management control ECU.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-13 (TC) - I3-11 (TC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE WIRE HARNESS

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)
a.
C204945C03
0.094,0.615 0.427,0.833 0.333,0.219 1.615,0.802 1.615,0.302 1.615,0.302 1.813,0.302 false 0.156,0.135 0.469,0.396 0.313,0.26 10 *1 0.177,0.646 0.49,0.948 0.313,0.302 10 I39 1.854,0.219 2.25,0.469 0.396,0.25 10 CG
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE WIRE HARNESS

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)
a.
C204945C04
0.156,0.594 0.49,0.823 0.333,0.229 1.958,1.76 1.792,1.76 1.792,1.76 1.792,1.344 false 0.125,0.115 0.406,0.396 0.281,0.281 10 *1 0.24,0.625 0.802,1.083 0.563,0.458 10 I39 2.021,1.688 2.354,1.979 0.333,0.292 10 TC
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-13 (TC) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE WIRE HARNESS OR REPLACE EACH ECU