Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2012.02–2015.04
RM2040EQ _56 Audio / Visual / Telematics _014716 AUDIO / VIDEO _0076806 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

This circuit is necessary for the Automatic Sound Levelizer (ASL) built into the radio and display receiver assembly.

The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume level in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume level based upon vehicle speed signals that it receives from the combination meter assembly.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E237358E01
0.427,1.637 1.550,1.788 1.123,0.151 10 Skid Control ECU 0.994,0.794 1.285,0.945 0.292,0.151 10 SP1 0.093,1.637 0.411,1.818 0.319,0.181 10 A28 0.61,4.649 2.381,4.974 1.772,0.324 10 Stereo Component Amplifier Assembly*2 0.317,4.649 0.636,4.830 0.319,0.181 10 I69 1.362,0.794 1.549,0.943 0.187,0.148 10 11 0.459,3.124 2.548,3.288 2.089,0.164 10 Power Management Control ECU 0.459,2.971 0.749,3.135 0.290,0.164 10 I3 1.624,2.719 2.025,2.873 0.400,0.154 10 SPDI 2.095,2.719 2.275,2.877 0.180,0.159 10 14 2.936,2.719 3.116,2.877 0.180,0.159 10 21 3.952,2.719 4.131,2.877 0.180,0.159 10 18 3.952,4.24 4.131,4.399 0.180,0.159 10 17 2.936,5.717 3.116,5.876 0.180,0.159 10 20 5.383,0.794 5.687,0.944 0.304,0.150 10 8 5.384,2.719 5.659,2.868 0.275,0.150 10 9 5.604,0.879 5.803,1.028 0.198,0.150 10 SI 5.598,2.817 5.799,2.968 0.201,0.151 10 +S 4.992,3.164 5.287,3.310 0.295,0.145 10 I18 5.264,3.164 7.100,3.320 1.835,0.156 10 Combination Meter Assembly 5.575,4.24 5.904,4.385 0.328,0.145 10 SPD 5.313,4.24 5.625,4.402 0.311,0.162 10 17 5.575,5.739 5.904,5.885 0.328,0.145 10 SPD 5.299,5.739 5.485,5.901 0.186,0.162 10 17 4.796,6.111 5.267,6.272 0.471,0.162 10 I67 5.037,6.111 7.125,6.301 2.088,0.190 10 Navigation ECU Sub-assembly*2 2.936,4.24 3.116,4.399 0.180,0.159 10 19 1.654,4.24 1.982,4.385 0.328,0.145 10 SPD 2.095,4.24 2.268,4.402 0.172,0.162 10 11 4.259,4.629 4.563,4.788 0.304,0.159 10 I155 4.609,4.629 7.122,4.816 2.513,0.187 10 Radio and Display Receiver Assembly*1 3.118,6.129 4.338,6.291 1.220,0.162 10 Junction Connector 2.778,6.129 3.178,6.293 0.400,0.164 10 I124 2.095,5.717 2.407,5.878 0.311,0.162 10 24 0.32,6.129 2.651,6.305 2.331,0.176 10 Windshield Wiper Relay Assembly*3 0.556,7.136 3.056,7.311 2.500,0.176 10 *1: for Radio and Display Type 2.797,7.136 4.818,7.311 2.021,0.176 10 *2: for Navigation Receiver Type 1.654,5.717 1.982,5.862 0.328,0.145 10 SPD 0.063,6.129 0.341,6.282 0.277,0.153 10 I72 5.123,7.136 6.774,7.311 1.651,0.176 10 *3: w/ Auto Wiper System

PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E227878

Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal Check Mode in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK


b.

While driving the vehicle, compare the "SPEED" indicator to the reading on the speedometer. Check if these readings are almost equal.

HINT:

The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.


OK:

Vehicle speed displayed on the "Vehicle Signal Check Mode" screen is almost the same as the actual vehicle speed measured using the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E265641C01
1.438,0.25 1.844,0.51 0.406,0.26 0.938,1.906 1.344,1.313 false 0.146,0.104 0.458,0.302 0.313,0.198 10 *a 1.552,0.302 1.865,0.5 0.313,0.198 10 I18 0.833,1.927 1.146,2.125 0.313,0.198 10 +S 1.01,4.219 1.615,4.521 0.604,0.302 10 (A) 2.698,3.865 3.302,4.167 0.604,0.302 10 GND
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal I18-9 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I18-9 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (INPUT WAVEFORM)

NG

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (INPUT WAVEFORM)
a.

Check the input waveform.

E265791C05
1.646,0.271 2.063,0.531 0.417,0.26 2.604,1.844 2.406,1.406 false 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 1.729,0.323 2.042,0.521 0.313,0.198 10 false I155 2.5,1.854 2.813,2.052 0.313,0.198 10 false SPD 4.75,1.729 5.063,1.927 0.313,0.198 10 false (A) 6.167,1.469 6.594,1.688 0.427,0.219 10 false GND
*a Component with harness connected
(Radio and Display Receiver Assembly)
- -


i.

Remove the radio and display receiver assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal I155-17 (SPD) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I155-17 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the radio and display receiver assembly connector.


b.

Disconnect the junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I155-17 (SPD) - I124-17 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - JUNCTION CONNECTOR)