Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM2040EQ _58 Vehicle Interior _014728 SEAT _0077333 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) U

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  TERMINALS OF ECU  


CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY


a.

Disconnect the d11 and d12 position control ECU and switch assembly connectors.

B219505
3.816,0.29 4.071,0.428 0.255,0.138 10 d11 2.922,0.289 3.171,0.43 0.249,0.142 10 d12 2.863,0.264 3.201,0.462 0.338,0.199 3.747,0.264 4.084,0.462 0.338,0.199


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal Connection Wiring Color Terminal Description Condition Specified Condition
d11-2 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
d11-7 (+B) - d11-2 (GND) W - W-B Power source Power switch off 11 to 14 V
d12-12 (SYSB) - d11-2 (GND) P - W-B System power source Power switch off 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the d11 and d12 position control ECU and switch assembly connectors.


d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal Connection Wiring Color Terminal Description Condition Specified Condition
d11-6 (+B2) - d11-1 (GND2) SB - W-B Lumbar support adjuster power source Power switch off 11 to 14 V
d11-1 (GND2) - Body ground W-B - Body ground Lumbar support adjuster ground Always Below 1 Ω
d11-3 (SLD+) - d11-2 (GND) L - W-B Slide motor signal (forward) Slide switch off Below 1 V
Slide switch on (Forward) 11 to 14 V
d11-4 (SLD-) - d11-2 (GND) GR - W-B Slide motor signal (rearward) Slide switch off Below 1 V
Slide switch on (Rearward) 11 to 14 V
d11-5 (FRV-) - d11-2 (GND) R - W-B Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch on (Downward) 11 to 14 V
d11-8 (FRV+) - d11-2 (GND) B - W-B Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch on (Upward) 11 to 14 V
d11-9 (RCL+) - d11-2 (GND) P - W-B Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch on (Forward) 11 to 14 V
d11-11 (RCL-) - d11-2 (GND) LG - W-B Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch on (Rearward) 11 to 14 V
d11-10 (LFT+) - d11-2 (GND) V - W-B Lifter motor signal (upward) Lifter switch off Below 1 V
Lifter switch on (Upward) 11 to 14 V
d11-12 (LFT-) - d11-2 (GND) G - W-B Lifter motor signal (downward) Lifter switch off Below 1 V
Lifter switch on (Downward) 11 to 14 V
d12-1 (SGND) - d11-2 (GND) BR - W-B Position sensor round Always Below 1 Ω
d12-3 (SSFV) - d12-1 (SGND) R - BR Front vertical position signal Front vertical function operating 4.5 to 4.8 V
d12-4 (SSRL) - d12-1 (SGND) P - BR Lifter position signal Lifter function operating 4.5 to 4.8 V
d12-5 (SSRS) - d12-1 (SGND) G- BR Slide position signal Slide function operating 4.5 to 4.8 V
d12-11 (SSRR) - d12-1 (SGND) V - BR Reclining position signal Reclining function operating 4.5 to 4.8 V

If the result is not as specified, the position control ECU and switch assembly may have a malfunction.



CHECK OUTER MIRROR CONTROL ECU ASSEMBLY RH


a.

Disconnect the J13 outer mirror control ECU assembly RH connector.

B209687
4,0.198 4.313,0.406 0.313,0.208 4.063,0.219 4.51,0.521 0.448,0.302 10 false J13


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
J13-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
J13-14 (BDR) - J13-7 (GND) W - W-B Power source Always 11 to 14 V
J13-5 (SIG) - J13-7 (GND) BE - W-B Power source (IG) Always Below 1 V
Engine switch on (IG) 11 to 14 V
J13-6 (CPUB) - J13-7 (GND) W - W-B Power source Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the J13 outer mirror control ECU assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
J13-3 (M2) - J13-13 (MSWE) B - V M2 switch signal for seat memory switch M2 switch on Below 1 V
M2 switch off 11 to 14 V
J13-2 (M1) - J13-13 (MSWE) G - V M1 switch signal for seat memory switch M1 switch on Below 1 V
M1 switch off 11 to 14 V
J13-1 (MM) - J13-13 (MSWE) P - V SET switch signal for seat memory switch SET switch on Below 1 V
SET switch off 11 to 14 V

If the result is not as specified, the outer mirror control ECU assembly RH may have a malfunction.



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


a.

Disconnect the MB, I12 and I13 main body ECU (multiplex network body ECU) connectors.

B278841
2.198,3.771 2.521,3.979 0.323,0.208 3.865,5.01 4.188,5.219 0.323,0.208 1.083,5.01 1.406,5.219 0.323,0.208 1.74,6.292 2.063,6.5 0.323,0.208 4.885,6.292 5.208,6.5 0.323,0.208 3.375,7.531 3.698,7.74 0.323,0.208 4.646,3.771 4.969,3.979 0.323,0.208 5.823,5.021 6.146,5.229 0.323,0.208 4.042,1.135 4.042,0.802 4.042,0.802 4.156,0.802 false 1.677,1.615 1.938,1.615 false 1.677,2.01 1.938,2.01 false 1.49,2.74 1.49,1.635 1.49,1.635 1.604,1.635 false 1.49,2.01 1.604,2.01 false 4.188,0.719 4.479,0.927 0.292,0.208 10 false MB 3.438,7.552 3.896,7.802 0.458,0.25 10 false MB 1.073,2.688 1.375,2.875 0.302,0.188 10 false 3E 0.896,1.521 1.198,1.74 0.302,0.219 10 false 3C 1.167,5.031 1.469,5.219 0.302,0.188 10 false 3C 5.865,1.458 6.135,1.635 0.271,0.177 10 false 3B 1.823,6.313 2.083,6.573 0.26,0.26 10 false 3B 5.854,2.135 6.104,2.313 0.25,0.177 10 false 3A 4.969,6.313 5.281,6.594 0.313,0.281 10 false 3A 0.906,2.104 1.198,2.292 0.292,0.188 10 false 3D 3.958,5.031 4.198,5.271 0.24,0.24 10 false 3D 1.99,1.542 2.354,1.74 0.365,0.198 10 false I13 4.729,3.792 5.26,4.135 0.531,0.344 10 false I13 1.99,1.948 2.344,2.167 0.354,0.219 10 false I12 2.271,3.792 2.719,4.083 0.448,0.292 10 false I12 5.906,5.042 6.271,5.365 0.365,0.323 10 false 3E 0.25,0.26 0.552,0.479 0.302,0.219 12 false *A 1.458,2.76 1.813,2.979 0.354,0.219 10 false *2
*A Main body ECU (multiplex network body ECU) with 2 connectors - -
*1 Main body ECU (multiplex network body ECU) *2 2 connectors


B282096
2.229,3.771 2.552,3.979 0.323,0.208 5.823,5.01 6.146,5.219 0.323,0.208 3.906,5.031 4.229,5.24 0.323,0.208 1.125,5.01 1.448,5.219 0.323,0.208 1.781,6.292 2.104,6.5 0.323,0.208 4.927,6.292 5.25,6.5 0.323,0.208 3.417,7.531 3.74,7.74 0.323,0.208 4.688,3.771 5.01,3.979 0.323,0.208 4.063,1.125 4.063,0.844 4.063,0.844 4.177,0.844 false 1.813,2.104 2.073,2.104 false 1.802,1.75 2.073,1.75 false 1.594,3.094 1.594,1.438 1.594,1.438 1.708,1.438 false 1.594,1.74 1.708,1.74 false 1.594,2.104 1.708,2.104 false 1.771,0.979 1.771,0.677 1.771,0.677 1.865,0.677 false 3.479,7.552 3.823,7.813 0.344,0.26 10 false MB 5.917,5.031 6.406,5.323 0.49,0.292 10 false 3F 1.219,5.031 1.51,5.25 0.292,0.219 10 false 3C 1.865,6.302 2.177,6.521 0.313,0.219 10 false 3B 5.01,6.302 5.323,6.594 0.313,0.292 10 false 3A 4,5.052 4.354,5.354 0.354,0.302 10 false 3D 4.771,3.792 5.083,4.031 0.313,0.24 10 false I13 2.313,3.792 2.917,4.188 0.604,0.396 10 false I12 5.854,2.125 6.167,2.385 0.313,0.26 10 false 3A 2.125,2.042 2.427,2.333 0.302,0.292 10 false I12 2.125,1.677 2.51,1.927 0.385,0.25 10 false I13 0.906,2.094 1.26,2.438 0.354,0.344 10 false 3D 1.083,2.667 1.479,2.99 0.396,0.323 10 false 3F 0.906,1.458 1.302,1.854 0.396,0.396 10 false 3C 5.854,1.427 6.208,1.667 0.354,0.24 10 false 3B 4.229,0.74 4.688,1.042 0.458,0.302 10 false MB 0.323,0.229 0.927,0.75 0.604,0.521 10 false *A 1.906,0.573 2.146,0.813 0.24,0.24 10 false *1 1.542,3.094 1.99,3.458 0.448,0.365 10 false *2
*A Main body ECU (multiplex network body ECU) with 3 connectors - -
*1 Main body ECU (multiplex network body ECU) *2 3 connectors



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
MB-30 (BECU) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-31 (ALTB) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-32 (IG) - Body ground - Ignition power supply (IG signal) Power switch on (IG) → off 11 to 14 V → Below 1 V
MB-29 (ACC) - Body ground - Ignition power supply (ACC signal) Power switch on (ACC) → off 11 to 14 V → Below 1 V
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
I12-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
I13-19 (FRCY) - Body ground Y - Body ground Front door courtesy light switch RH input Front door RH closed (OFF) → open (ON) 10 kΩ or higher → Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.