Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM2040EQ _58 Vehicle Interior _014728 SEAT _0077333 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2653  Lifter Sensor Malfunction  


DESCRIPTION

When the position control ECU and switch assembly does not receive a sensor signal despite upward or downward movement of the seat by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2653 Lifter Sensor Malfunction The upward and downward lock detection position of the sensor is the same.
·

Position control ECU and switch assembly

·

Lifter motor (separate type front seat cushion spring assembly)

·

Wire harness or connector



WIRING DIAGRAM

B348529
1.021,3.823 2.719,4.229 1.698,0.406 10 false Separate Type Front Seat Cushion Spring Assembly 1.375,3.052 1.833,3.25 0.458,0.198 10 false d10 1.385,3.208 2.115,3.49 0.729,0.281 10 false Lifter Motor 4.885,2.521 5.042,2.719 0.156,0.198 10 false 1 2.26,1.063 2.417,1.26 0.156,0.198 10 false 4 2.26,2.083 2.417,2.281 0.156,0.198 10 false 2 2.26,2.594 2.417,2.792 0.156,0.198 10 false 3 4.813,1.177 5.271,1.375 0.458,0.198 10 false d11 4.813,1.677 5.271,1.875 0.458,0.198 10 false d11 4.813,2.177 5.271,2.375 0.458,0.198 10 false d12 4.813,2.688 5.271,2.885 0.458,0.198 10 false d12 4.844,1.01 5.156,1.208 0.313,0.198 10 false 10 4.844,1.51 5.156,1.708 0.313,0.198 10 false 12 4.885,2.01 5.042,2.208 0.156,0.198 10 false 4 2.26,1.563 2.417,1.76 0.156,0.198 10 false 1 5.146,1.188 5.76,1.385 0.615,0.198 10 false LFT+ 5.146,1.698 5.76,1.896 0.615,0.198 10 false LFT- 5.146,2.198 5.76,2.396 0.615,0.198 10 false SSRL 5.146,2.708 5.76,2.906 0.615,0.198 10 false SGND 4.896,3.823 6.479,4.219 1.583,0.396 10 false Position Control ECU and Switch Assembly

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (LIFTER MOTOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Lifter Operation Seat lifter operation OFF/Down/Up -
Body Electrical > Driver Seat > Active Test
Tester Display
Lifter Operation
50004 162 2
OK:

Motor operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (LIFTER MOTOR CIRCUIT)

NG

5.INSPECT LIFTER MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)
2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (LIFTER MOTOR CIRCUIT)
a.

Disconnect the d10 lifter motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
d10-2 - d10-3 Lifter switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

3.CHECK LIFTER MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - LIFTER MOTOR)
3.CHECK LIFTER MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)
a.
B238515
1.552,0.323 1.927,0.573 0.375,0.25 0.146,0.094 0.49,0.448 0.344,0.354 10 false *a 1.646,0.365 2.146,0.615 0.5,0.25 10 false d10
*a Component with harness connected
(Lifter Motor (Separate Type Front Seat Cushion Spring Assembly))


Reconnect the d10 lifter motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
d10-2 - Body ground Lifter switch on 4.5 to 4.8 V



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPLACE LIFTER MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - LIFTER MOTOR)
a.

Disconnect the d12 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d12-4 (SSRL) - d10-2 Always Below 1 Ω
d12-1 (SGND) - d10-3 Always Below 1 Ω
d12-4 (SSRL) - Body ground Always 10 kΩ or higher
d12-1 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT LIFTER MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)
a.
B238256
0.323,0.344 0.542,0.531 0.219,0.188 10 *a
*a Component without harness connected
(Lifter Motor (Separate Type Front Seat Cushion Spring Assembly))


Disconnect the d10 lifter motor connector.


b.

Check if the seat cushion spring moves smoothly when the auxiliary battery is connected to the lifter motor connector terminals.

OK:
Measurement Condition Operational Direction
Auxiliary battery positive (+) → Terminal 4
Auxiliary battery negative (-) → Terminal 1
Seat cushion spring moves upward
Auxiliary battery positive (+) → Terminal 1
Auxiliary battery negative (-) → Terminal 4
Seat cushion spring moves downward



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - LIFTER MOTOR)

NG

REPLACE LIFTER MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - LIFTER MOTOR)
a.

Disconnect the d11 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d11-10 (LFT+) - d10-4 Always Below 1 Ω
d11-12 (LFT-) - d10-1 Always Below 1 Ω
d11-10 (LFT+) - Body ground Always 10 kΩ or higher
d11-12 (LFT-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR