Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM2040EQ _58 Vehicle Interior _014728 SEAT _0077333 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2658  Short in Sensor with Motor Power Supply Circuit  


DESCRIPTION

This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2658 Short in Sensor with Motor Power Supply Circuit Problem with the voltage supplied to the position control sensor.
·

Position control ECU and switch assembly

·

Separate type front seat cushion spring assembly

·

Front seatback frame sub-assembly RH

·

Wire harness or connector



WIRING DIAGRAM

B270910E32
1.354,1.573 1.615,1.75 0.26,0.177 10 false d8 1.354,1.719 2.104,1.896 0.75,0.177 10 false Slide Motor 5.219,1.271 5.688,1.438 0.469,0.167 10 false SGND 5.219,0.719 5.688,0.885 0.469,0.167 10 false SSRS 2.292,0.625 2.51,0.781 0.219,0.156 10 false 2 2.292,1.188 2.51,1.344 0.219,0.156 10 false 3 5.021,0.615 5.188,0.833 0.167,0.219 10 false 5 1.354,7.135 1.615,7.313 0.26,0.177 10 false f3 1.354,7.292 2.354,7.469 1,0.177 10 false Reclining Motor 5.219,6.469 5.688,6.635 0.469,0.167 10 false SSRR 2.302,2.292 2.521,2.448 0.219,0.156 10 false 2 2.302,2.698 2.521,2.854 0.219,0.156 10 false 3 4.938,6.365 5.115,6.521 0.177,0.156 10 false 11 1.354,3.073 1.604,3.25 0.25,0.177 10 false d9 1.354,3.229 2.604,3.406 1.25,0.177 10 false Front Vertical Motor 5.219,2.396 5.688,2.563 0.469,0.167 10 false SSFV 2.302,3.813 2.521,3.969 0.219,0.156 10 false 2 2.302,4.208 2.521,4.365 0.219,0.156 10 false 3 5.021,2.281 5.188,2.5 0.167,0.219 10 false 3 1.354,4.583 1.615,4.76 0.26,0.177 10 false d10 1.354,4.729 2.104,4.906 0.75,0.177 10 false Lifter Motor 5.219,3.906 5.688,4.073 0.469,0.167 10 false SSRL 2.302,6.365 2.521,6.521 0.219,0.156 10 false 2 2.302,6.75 2.521,6.906 0.219,0.156 10 false 3 5.021,3.792 5.156,3.99 0.135,0.198 10 false 4 5.021,1.167 5.375,1.417 0.354,0.25 10 false 1 0.781,5.365 2.917,5.813 2.135,0.448 10 false Separate Type Front Seat Cushion Spring Assembly 1.146,7.927 2.604,8.417 1.458,0.49 10 false Front Seatback Frame Sub-Assembly RH 5.031,8.021 6.604,8.438 1.573,0.417 10 false Position Control ECU and Switch Assembly 5.031,7.865 5.688,8.229 0.656,0.365 10 false d12

PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Clear DTCs
50002 162

b.

Check for DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2658 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - SLIDE MOTOR)
2.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - SLIDE MOTOR)
a.

Disconnect the d12 position control ECU and switch assembly connector.


b.

Disconnect the d8 slide motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d12-5 (SSRS) - d8-2 Always Below 1 Ω
d12-1 (SGND) - d8-3 Always Below 1 Ω
d12-5 (SSRS) - d12-1 (SGND) Always 10 kΩ or higher
d12-5 (SSRS) - Body ground Always 10 kΩ or higher
d12-1 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (SLIDE MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (SLIDE MOTOR CIRCUIT)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
d8-2 - d8-3 Sliding switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT VERTICAL MOTOR)

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT VERTICAL MOTOR)
a.

Disconnect the d9 front vertical motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d12-3 (SSFV) - d9-2 Always Below 1 Ω
d12-1 (SGND) - d9-3 Always Below 1 Ω
d12-3 (SSFV) - d12-1 (SGND) Always 10 kΩ or higher
d12-3 (SSFV) - Body ground Always 10 kΩ or higher
d12-1 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (FRONT VERTICAL MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (FRONT VERTICAL MOTOR CIRCUIT)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
d9-2 - d9-3 Front vertical switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - LIFTER MOTOR)

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - LIFTER MOTOR)
a.

Disconnect the d10 lifter motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d12-4 (SSRL) - d10-2 Always Below 1 Ω
d12-1 (SGND) - d10-3 Always Below 1 Ω
d12-4 (SSRL) - d12-1 (SGND) Always 10 kΩ or higher
d12-4 (SSRL) - Body ground Always 10 kΩ or higher
d12-1 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (LIFTER MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (LIFTER MOTOR CIRCUIT)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
d10-2 - d10-3 Lifter switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

8.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

8.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY
a.

Replace the separate type front seat cushion spring assembly.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY


b.

Clear the DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Clear DTCs
50002 162

c.

Check for DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2658 is not output.



Result:
Proceed to
OK
NG



OK

END (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY WAS DEFECTIVE)

NG

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - RECLINING MOTOR)
9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - RECLINING MOTOR)
a.

Disconnect the d12 position control ECU and switch assembly connector.


b.

Disconnect the f3 reclining motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d12-11 (SSRR) - f3-2 Always Below 1 Ω
d12-1 (SGND) - f3-3 Always Below 1 Ω
d12-11 (SSRR) - d12-1 (SGND) Always 10 kΩ or higher
d12-11 (SSRR) - Body ground Always 10 kΩ or higher
d12-1 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (RECLINING MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (RECLINING MOTOR CIRCUIT)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
f3-2 - f3-3 Reclining switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

11.REPLACE FRONT SEATBACK FRAME SUB-ASSEMBLY RH

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

11.REPLACE FRONT SEATBACK FRAME SUB-ASSEMBLY RH
a.

Replace the front seatback frame sub-assembly RH.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY


b.

Clear the DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Clear DTCs
50002 162

c.

Check for DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2658 is not output.



Result:
Proceed to
OK
NG



OK

END (FRONT SEATBACK FRAME SUB-ASSEMBLY RH WAS DEFECTIVE)

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY