Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2012.02–2015.04
RM2040EQ _58 Vehicle Interior _014725 METER / GAUGE / DISPLAY _0075073 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Entire Combination Meter does not Operate  


DESCRIPTION

This circuit is the power source circuit for the meter. This circuit provides two types of power sources; one is a constant power source, and the other is an IG power source.

WIRING DIAGRAM

E143732E41
5.26,5.052 7.135,5.219 1.875,0.167 10 false Combination Meter Assembly 6.146,1.292 6.427,1.448 0.281,0.156 10 false B 6.146,2.271 6.531,2.427 0.385,0.156 10 false IG+ 6.146,3.271 6.385,3.427 0.24,0.156 10 false ES 5.875,1.167 6.052,1.323 0.177,0.156 10 false 1 5.875,2.156 6.052,2.313 0.177,0.156 10 false 13 5.26,4.917 5.542,5.073 0.281,0.156 10 false I18 5.875,3.156 6.052,3.313 0.177,0.156 10 false 7 3.323,2.396 4.208,2.688 0.885,0.292 10 false METER-IG2 4.479,1.448 5.354,1.594 0.875,0.146 10 false ECU-B NO. 1 1.708,1.26 3.094,1.604 1.385,0.344 10 false from Auxiliary Battery 0.198,2.271 1.302,2.417 1.104,0.146 10 false from IG2 Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY CIRCUIT)
a.
E224284C15
0.271,1.875 0.729,2.156 0.458,0.281 1.729,1.906 1.729,0.698 1.729,0.698 1.927,0.698 false 0.979,2.146 0.979,2.552 0.979,2.552 0.781,2.552 false 0.979,1.906 0.979,1.25 0.979,1.25 0.781,1.25 false 0.115,0.083 0.396,0.365 0.281,0.281 10 *a 1.969,0.625 2.458,1 0.49,0.375 10 ES 0.656,1.177 1.188,1.417 0.531,0.24 10 B 0.417,1.927 0.917,2.219 0.5,0.292 10 I18 0.542,2.479 1.073,2.719 0.531,0.24 10 IG+
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the I18 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-7 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I18-13 (IG+) - Body ground Power switch off Below 1 V
Power switch on (IG) 11 to 14 V
I18-1 (B) - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR