Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM
RM2040EQ _58 Vehicle Interior _014722 DOOR LOCK _0075052 WIRELESS DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The door control receiver is used to receive radio waves relating to the entry functions of the electrical key transmitter sub-assembly. The certification ECU (smart key ECU assembly) decodes the requested electrical key transmitter sub-assembly by identifying a key code based on the electric waves received via the door control receiver. The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly). The certification ECU (smart key ECU assembly) then sends a command, according to the requested operation, to each ECU (ex. if door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the main body ECU (multiplex network body ECU)).

DTC No. Detection Item DTC Detection Condition Trouble Area
B1242 Wireless Door Lock Tuner Circuit Malfunction
·

Short in RDAM to ground between the certification ECU (smart key ECU assembly) and the door control receiver.

·

Short in RDAM to ground when RCO (5 V) output from the ECU is off.


·

Wire harness or connector

·

Door control receiver

·

Certification ECU (Smart key ECU assembly)



WIRING DIAGRAM

B477391E03
1.156,0.865 1.771,1.063 0.615,0.198 10 false DATA 1.333,1.635 1.948,1.833 0.615,0.198 10 false +5 1.229,2.344 1.844,2.542 0.615,0.198 10 false GND 5.75,2.344 6.365,2.542 0.615,0.198 10 false E 5.74,1.646 6.354,1.844 0.615,0.198 10 false RCO 5.75,0.844 6.365,1.042 0.615,0.198 10 false RDAM 0.406,2.854 1.021,3.052 0.615,0.198 10 false O25 0.417,3.031 1.771,3.26 1.354,0.229 10 false Door Control Receiver 5.542,2.854 7.063,3.25 1.521,0.396 10 false Certification ECU (Smart Key ECU Assembly) 5.396,0.854 6.01,1.052 0.615,0.198 10 false O2 5.396,1.646 6.01,1.844 0.615,0.198 10 false O2 5.406,2.333 6.021,2.531 0.615,0.198 10 false I86 5.438,0.635 6.052,0.833 0.615,0.198 10 false 6 5.406,1.438 6.021,1.635 0.615,0.198 10 false 15 5.448,2.125 6.063,2.323 0.615,0.198 10 false 1 1.656,2.219 2.271,2.417 0.615,0.198 10 false 1 1.656,1.521 2.271,1.719 0.615,0.198 10 false 4 1.656,0.729 2.271,0.927 0.615,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, entry and wireless function performance may be affected.

·

Before performing the inspection, check that there are no problems related to the CAN communication system.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to the Service Bulletin.

·

This DTC is not detected within 10 seconds after the power switch turned to off from on (IG).



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Disconnect the O25 door control receiver connector.


b.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

B440800C01
2.146,0.104 2.521,0.323 0.375,0.219 3.542,0.104 3.917,0.323 0.375,0.219 4.74,0.104 5.115,0.323 0.375,0.219 1.656,1.521 1.833,1.521 1.833,1.521 2,0.771 false 2.885,1.51 2.708,1.51 2.708,1.51 2.573,0.854 false 5.823,1.521 5.604,1.521 5.604,1.521 5.438,0.76 false 2.25,0.125 2.563,0.323 0.313,0.198 10 false O2 3.646,0.125 3.958,0.323 0.313,0.198 10 false I87 4.844,0.125 5.156,0.323 0.313,0.198 10 false I86 1.198,1.427 1.656,1.635 0.458,0.208 10 false RDAM 2.927,1.427 3.385,1.635 0.458,0.208 10 false RCO 5.875,1.427 6.104,1.615 0.229,0.188 10 false E 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Voltage:
Tester Connection Condition Specified Condition
O2-15 (RCO) - I86-1 (E) Always Below 1 V → 4.5 to 5.5 V
(Pulse generation)
O2-6 (RDAM) - I86-1 (E) Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
I86-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE DOOR CONTROL RECEIVER

NG

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the O2 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O2-6 (RDAM) - O25-5 (DATA) Always Below 1 Ω
O2-15 (RCO) - O25-4 (+5) Always Below 1 Ω
O25-1 (GND) - Body ground Always Below 1 Ω
O2-6 (RDAM) or O25-5 (DATA) - Body ground Always 10 kΩ or higher
O2-15 (RCO) or O25-4 (+5) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR