Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function) › 2012.02–2015.04
RM2040EQ _56 Audio / Visual / Telematics _014718 PARK ASSIST / MONITORING _0075024 PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function) C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function)  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the navigation ECU sub-assembly receives a signal via CAN communication from the steering sensor that indicates a power supply problem.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1625 Open or Short in Steering Angle Sensor +B Open or short in steering angle sensor +B
·

Harness or connector

·

Steering sensor



WIRING DIAGRAM

E224380E45
1.135,3.219 2.885,3.396 1.75,0.177 10 false : CAN Communication Line 3.229,0.635 3.583,0.813 0.354,0.177 10 false BAT 3.229,1.74 3.563,1.917 0.333,0.177 10 false ESS 2.021,1.354 3.031,1.531 1.01,0.177 10 false ECU-IG1 NO. 1 2.042,0.792 2.969,0.969 0.927,0.177 10 false ECU-B NO. 1 0.333,1.198 1.927,1.552 1.594,0.354 10 false from IG1 NO. 2 Relay 0.333,0.625 1.854,0.958 1.521,0.333 10 false from Auxiliary Battery 3.188,2.333 4.26,2.75 1.073,0.417 10 false Steering Sensor 3.031,0.552 3.156,0.729 0.125,0.177 10 false 5 3.031,1.094 3.156,1.271 0.125,0.177 10 false 4 3.031,1.646 3.156,1.823 0.125,0.177 10 false 1 3.229,1.188 3.531,1.365 0.302,0.177 10 false IG 4.99,2.083 5.396,2.344 0.406,0.26 10 false I67 3.198,2.188 3.542,2.365 0.344,0.177 10 false I30 4.99,2.229 6.927,2.583 1.938,0.354 10 false Navigation ECU Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When "System initializing" is displayed on the navigation ECU sub-assembly after disconnecting the cable from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function)>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function)>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING SENSOR POWER SUPPLY)
a.
E224381C03
1.49,0.156 1.906,0.448 0.417,0.292 2.052,1.51 2.49,1.51 false 1.865,1.583 1.865,1.885 1.865,1.885 2.49,1.885 false 1.427,1.583 1.427,1.885 1.427,1.885 0.802,1.885 false 0.458,1.802 0.875,2 0.417,0.198 10 false ESS 2.521,1.802 2.938,2 0.417,0.198 10 false IG 2.521,1.427 2.938,1.625 0.417,0.198 10 false BAT 0.188,0.115 0.688,0.479 0.5,0.365 10 false *a 1.615,0.219 1.969,0.49 0.354,0.271 10 false I30
*a Front view of wire harness connector
(to Steering Sensor)


Disconnect the I30 connector from the steering sensor.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I30-1 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I30-4 (IG) - I30-1 (ESS) Power switch on (IG) 11 to 14 V
I30-5 (BAT) - I30-1 (ESS) Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR