Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2012.02–2015.04
RM2040EQ _56 Audio / Visual / Telematics _014718 PARK ASSIST / MONITORING _0075026 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the blind spot monitor sensor.

WIRING DIAGRAM

E224413E12
3.625,0.719 3.938,0.896 0.313,0.177 10 false BLB 3.458,0.604 3.573,0.781 0.115,0.177 10 false 5 3.625,3.302 3.938,3.479 0.313,0.177 10 false BRB 3.458,3.198 3.573,3.375 0.115,0.177 10 false 5 3.656,4.104 4.094,4.281 0.438,0.177 10 false BRGD 3.458,3.979 3.573,4.156 0.115,0.177 10 false 1 3.458,1.396 3.573,1.573 0.115,0.177 10 false 1 3.625,1.51 4.052,1.667 0.427,0.156 10 false BLGD 1.604,0.865 2.635,1.031 1.031,0.167 10 false ECU-IG1 NO. 3 0.219,0.708 1.219,1.208 1,0.5 10 false from IG1 NO. 2 Relay 6.365,1.104 6.896,1.281 0.531,0.177 10 false to CAN 3.417,2.052 3.958,2.333 0.542,0.281 10 false T10 3.417,2.219 5.031,2.563 1.615,0.344 10 false Blind Spot Monitor Sensor LH 3.469,4.802 5.083,5.146 1.615,0.344 10 false Blind Spot Monitor Sensor RH 0.875,5.302 2.719,5.458 1.844,0.156 10 false : CAN Communication Line 3.469,4.635 3.875,4.792 0.406,0.156 10 false O28

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH -AUXILIARY BATTERY)
a.

Disconnect connector O28 from the blind spot monitor sensor RH.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O28-5 (BRB) - Body ground Power switch on (IG) 11 to 14 V
O28-5 (BRB) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BODY GROUND)
a.

Disconnect connector O28 from the blind spot monitor sensor RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O28-1 (BRGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - AUXILIARY BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - AUXILIARY BATTERY)
a.

Disconnect connector T10 from the blind spot monitor sensor LH.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T10-5 (BLB) - Body ground Power switch on (IG) 11 to 14 V
T10-5 (BLB) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BODY GROUND)
a.

Disconnect connector T10 from the blind spot monitor sensor LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T10-1 (BLGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR