Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for HDD) › 2012.02–2015.04
RM2040EQ _56 Audio / Visual / Telematics _014717 NAVIGATION / MULTI INFO DISPLAY _0078805 NAVIGATION SYSTEM(for HDD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for HDD)  Radio Broadcast cannot be Received or Poor Reception  


PROCEDURE

1.CHECK NAVIGATION ECU SUB-ASSEMBLY
a.

Check the radio automatic station search function.

i.

Check the radio automatic station search function by activating it.

Result:
Result Proceed to
Automatic station search function does not stop A
Automatic station search function stops on a station B





A

2.CHECK OPTIONAL COMPONENTS

B

2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

Result:
Result Proceed to
Optional components are not installed A
Optional components are installed B


NOTICE:

Do not remove optional components without the permission of the customer.




A

3.CHECK NAVIGATION ECU SUB-ASSEMBLY

B

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3.CHECK NAVIGATION ECU SUB-ASSEMBLY
a.
E187251

Preparation for check

i.

Remove the antenna connector from the navigation ECU sub-assembly.



b.

Check for noise

i.

Turn the power switch on (ACC) with the navigation ECU sub-assembly connector connected.


ii.

Turn the radio on and tune into AM mode.


iii.

Place a screwdriver, thin wire or other metal object on the navigation ECU sub-assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise can be heard from the speakers.




Result:
Proceed to
OK
NG



OK

4.CHECK WINDOW GLASS ANTENNA WIRE

NG

4.CHECK WINDOW GLASS ANTENNA WIRE
a.
E111994C18
0.432,0.608 0.62,0.765 0.188,0.156 10 *a 0.946,1.965 1.141,2.114 0.195,0.149 10 *b 2.178,1.735 2.366,1.885 0.188,0.149 10 *c 0.528,0.797 0.602,1.13 false 0.97,1.623 1.044,1.956 false 2.192,1.375 2.266,1.708 false
*a Tester Probe
*b Antenna Wire
*c Tin Foil


Check for continuity in the window glass antenna wire.

HINT:

Check for continuity at the center of each antenna wire as shown in the illustration.


NOTICE:

When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger, as shown in the illustration.


OK:

There is continuity in the window glass antenna wire.



Result:
Proceed to
OK
NG



OK

5.INSPECT NAVIGATION ECU SUB-ASSEMBLY

NG

5.INSPECT NAVIGATION ECU SUB-ASSEMBLY
a.

Disconnect the navigation ECU sub-assembly connector.


b.
E188455C19
0.479,0.958 1.01,1.25 0.531,0.292 1.542,1.094 1.135,1.448 false 0.229,0.177 0.594,0.458 0.365,0.281 10 false *a 0.625,1.021 1.052,1.313 0.427,0.292 10 false RA 0.833,1.479 1.25,1.646 0.417,0.167 10 false ANT+
*a Component without harness connected
(Navigation ECU Sub-assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
RA-5 (ANT+) - Body ground Power switch on (ACC)
Radio switch on and AM or FM selected
11 to 14 V



Result:
Proceed to
OK
NG



OK

6.REPLACE ANTENNA CORD SUB-ASSEMBLY

NG

6.REPLACE ANTENNA CORD SUB-ASSEMBLY
a.

Replace the antenna cord sub-assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

NORMAL OPERATION

NG

7.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
7.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the No. 2 antenna cord sub-assembly.


b.

Measure the resistance of the No. 2 antenna cord sub-assembly to check for an open circuit in the No. 2 antenna cord sub-assembly.

Standard Resistance:

Below 1 Ω



c.

Measure the resistance between the No. 2 antenna cord sub-assembly and body ground to check for a short circuit in the No. 2 antenna cord sub-assembly.

Standard Resistance:

10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE AMPLIFIER ANTENNA ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

8.REPLACE AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the amplifier antenna assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

NORMAL OPERATION

NG