Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for HDD) › 2012.02–2015.04
RM2040EQ _56 Audio / Visual / Telematics _014717 NAVIGATION / MULTI INFO DISPLAY _0078805 NAVIGATION SYSTEM(for HDD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for HDD)  Sound Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier  


DESCRIPTION

The navigation ECU sub-assembly sends a sound signal to the stereo component amplifier assembly via this circuit.

The sound signal that has been sent is amplified by the stereo component amplifier assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.

WIRING DIAGRAM

E239591E03
1.156,0.958 1.313,1.115 0.156,0.156 10 false L- 1.146,1.448 1.406,1.656 0.26,0.208 10 false L+ 1.156,1.896 1.365,2.052 0.208,0.156 10 false R- 1.146,2.385 1.365,2.552 0.219,0.167 10 false R+ 1.427,0.854 1.615,1.021 0.188,0.167 10 false 2 1.438,1.323 1.625,1.49 0.188,0.167 10 false 3 1.427,1.792 1.615,1.958 0.188,0.167 10 false 4 1.427,2.26 1.615,2.427 0.188,0.167 10 false 5 5.698,0.865 5.813,1.031 0.115,0.167 10 false 6 5.719,1.323 5.823,1.49 0.104,0.167 10 false 2 5.698,2.271 5.802,2.438 0.104,0.167 10 false 1 5.698,1.802 5.813,1.969 0.115,0.167 10 false 5 5.885,0.979 6.219,1.135 0.333,0.156 10 false FL- 5.885,1.438 6.219,1.594 0.333,0.156 10 false FL+ 5.885,1.917 6.219,2.073 0.333,0.156 10 false FR- 5.885,2.396 6.219,2.552 0.333,0.156 10 false FR+ 5.708,2.813 6.031,2.99 0.323,0.177 10 false I64 5.698,2.99 6.719,3.49 1.021,0.5 10 false Navigation ECU Sub-assembly 0.354,2.781 0.656,2.948 0.302,0.167 10 false I69 0.365,2.948 1.563,3.313 1.198,0.365 10 false Stereo Component Amplifier Assembly 3.25,2.656 4.063,2.906 0.813,0.25 10 false (Shielded) 1.031,0.479 1.375,0.635 0.344,0.156 10 false SLD 1.427,0.375 1.615,0.542 0.188,0.167 10 false 6

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the navigation ECU sub-assembly connector.


b.

Disconnect the stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I69-5 (R+) - I64-1 (FR+) Always Below 1 Ω
I69-4 (R-) - I64-5 (FR-) Always Below 1 Ω
I69-3 (L+) - I64-2 (FL+) Always Below 1 Ω
I69-2 (L-) - I64-6 (FL-) Always Below 1 Ω
I69-6 (SLD) - Body ground Always 10 kΩ or higher
I69-5 (R+) - Body ground Always 10 kΩ or higher
I69-4 (R-) - Body ground Always 10 kΩ or higher
I69-3 (L+) - Body ground Always 10 kΩ or higher
I69-2 (L-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR