Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for HDD) › 2013.07–2015.04
RM2040EQ _56 Audio / Visual / Telematics _014717 NAVIGATION / MULTI INFO DISPLAY _0078805 NAVIGATION SYSTEM(for HDD) D

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for HDD)  OPERATION CHECK  


CHECK NAVIGATION SYSTEM NORMAL CONDITION


a.

If the symptom is applicable to any of the following, it is intended behavior, and not a malfunction.

Symptom Answer
A longer route than expected is chosen. Depending on the road conditions, the navigation receiver assembly may determine that a longer route is quicker.
Even when distance priority is high, the shortest route is not shown. Some routes may not be advised due to safety concerns.
When the vehicle is put into motion immediately after the engine starts, the navigation system deviates from the correct position. If the vehicle starts before the navigation system activates, the system may not react.
When driving on certain types of roads, especially new roads, the vehicle position deviates from the correct position. When the vehicle is driving on new roads not available on the hard disk drive, the system attempts to match it to another nearby road, causing the position mark to deviate.


b.
I100066

The following symptoms are not malfunctions, but are caused by errors inherent in the GPS, gyro sensor, speed sensor or navigation receiver assembly.

i.

The current position mark may be displayed on a nearby parallel road.


ii.
I100067

Immediately after a fork in the road, the current vehicle position mark may be displayed on the wrong road.


iii.
I100068

When the vehicle turns right or left at an intersection, the current vehicle position mark may be displayed on a nearby parallel road.


iv.
I100069

When the vehicle is carried, such as on a ferry, and the vehicle itself is not driving, the current vehicle position mark may be displayed in the position where the vehicle was until a measurement can be performed by the GPS.


v.
I100070

When the vehicle travels on a steep hill, the current vehicle position mark may deviate from the correct position.


vi.
I100071

When the vehicle makes a continuous turn (e.g. 360, 720, 1080 degrees), the current vehicle position mark may deviate from the correct position.


vii.
I100072

When the vehicle moves erratically, such as constant lane changes, the current vehicle position mark may deviate from the correct position.


viii.
E106418

When the power switch is turned to on (ACC or IG) and the vehicle is turned on a turntable before parking, the current vehicle position mark may not indicate the correct direction. The same will occur when the vehicle comes out of the parking garage.


ix.
I100074

When the vehicle travels on a snowy road or a mountain path with tire chains installed or using a spare tire, the current vehicle position mark may deviate from the correct position.


x.
I100075

When the tires are changed, the current vehicle position mark may deviate from the correct position.

HINT:
·

A change in tire diameter may cause a speed sensor error.

·

Performing "tire change" in calibration mode will allow the system to correct the current vehicle position faster.






CHECK HARD DISK DRIVE


HINT:
·

Check the hard disk drive (HDD) built into the navigation receiver assembly.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E226244

Select "Failure Diagnosis" from the "Service Menu" screen.


c.
E225796

Select "HDD Check" from the "Failure Diagnosis" screen.


d.
E225797C03
2.479,0.833 2.479,1.76 false 2.406,1.792 2.646,2.01 0.24,0.219 10 false *a
*a Result


HDD Check

i.

Select "HDD Check" to start the HDD check.


ii.

Check that the result is displayed when the HDD check is completed.

Screen Description
Display (Result) Description
Checking Check is in progress
OK Hard disk drive is normal
NG Hard disk drive is malfunctioning

HINT:
·

After selecting "HDD Check", it may take a while until the result is displayed.

·

If the cabin temperature is -20°C (-4°F) or lower, or 65°C (149°F) or higher, the HDD may not operate normally, and "NG" may be shown on the display. Make sure to perform the inspection with the cabin at an appropriate temperature.

·

If "NG" is displayed even when the cabin temperature is appropriate, replace the HDD with a new one.






CHECK PANEL & STEERING SWITCH


HINT:
·

The navigation receiver assembly panel switches and steering switches are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E225778

Select "Panel & Steering Switch" from the "Function Check/Setting I" screen.


d.
E225786N07
2.25,1.406 3.063,1.406 false 0.333,1.146 1.031,1.146 false 2.865,1.063 3.063,1.063 false 0.146,1.052 0.375,1.26 0.229,0.208 10 false *a 3.083,0.958 3.365,1.292 0.281,0.333 10 false *b 3.083,1.323 3.365,1.563 0.281,0.24 10 false *c

Panel & Steering Switch Check Mode

Screen Description
Display Content
*a: Switch condition "Pushed" is displayed when any switch is pushed
*b: Number of switches pushed
·

Number of switches pushed at once is displayed

·

If more than 3 switches are pushed at once, "More than 3" is displayed


*c: Rotary switch direction Direction of rotary switch is displayed

i.

Operate each switch and check that the switch conditions are correctly displayed.

NOTICE:

When the "SETUP" switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.





CHECK TOUCH SWITCH


HINT:
·

The touch switches on the screen are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E225779

Select "Touch Switch" from the "Function Check/Setting I" screen.


d.

Touch Switch Check

i.
E176521

Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

HINT:
·

A "+" mark is displayed where the display is touched.

·

The "+" mark remains on the display even after the finger is removed.






CHECK MIC & VOICE RECOGNITION


HINT:
·

The microphone and microphone input level are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E225780

Select "Mic & Voice Recognition" from the "Function Check/Setting I" screen.


d.
E187218N04
2.208,0.729 2.531,0.177 2.531,0.177 2.26,0.177 true 1.74,1.396 1.74,1.885 false 2.083,1.396 2.083,1.896 false 2.417,1.396 2.417,1.896 false 2.875,1.323 3.125,1.323 false 2.052,0.083 2.333,0.292 0.281,0.208 10 false *a 1.656,1.917 1.833,2.073 0.177,0.156 10 false *b 2.01,1.917 2.25,2.125 0.24,0.208 10 false *c 2.354,1.917 2.531,2.073 0.177,0.156 10 false *d 3.167,1.229 3.344,1.385 0.177,0.156 10 false *e

Microphone & Voice Recognition Check

Screen Description
Display Content
*a: Microphone input level meter Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.
*b: Recording switch Starts recording.
*c: Stop switch Stops recording and playing.
*d: Play switch Plays the recorded voice.
*e: Recording indicator Comes on while recording.

i.

When speaking into the microphone, check that the microphone input level meter changes according to the input level.

HINT:

The microphone is active at all times when this screen is displayed.



ii.

Push the recording switch and perform voice recording.

HINT:
·

Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.

·

While recording or playing, the switches other than the stop switch cannot be pushed.

·

When no recording is present, the play switch cannot be pushed.

·

Recording will stop after 5 seconds or when the stop switch is pushed.




iii.

Check that the recording indicator remains on while recording and that the recording can be played normally.




CHECK COLOR BAR


HINT:
·

The display color on the screen is checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E225781

Select "Color Bar" from the "Function Check/Setting I" screen.


d.

Color Bar Check Mode

i.
E226305

Select a color bar from the "Color Bar Check Mode" screen.


ii.

Check the display color.

HINT:
·

The entire screen turns to the color or stripe selected.

·

Touching the display will return to the "Color Bar Check Mode" screen.






CHECK GPS & VEHICLE SENSORS


HINT:
·

GPS information, vehicle signals and sensor signals are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E225782

Select "GPS & Vehicle Sensors" from the "Function Check/Setting I" screen.


d.
E225775N03
0.573,0.792 0.302,0.792 false 2.677,0.875 3.115,0.875 false 0.583,1.479 0.302,1.479 false 1.51,1.083 0.302,1.094 false 2.844,1.104 3.104,1.104 false 2.896,1.469 3.115,1.469 false 2.302,1.615 3.115,1.615 false 0.073,0.708 0.271,0.875 0.198,0.167 10 false *a 0.073,1.396 0.271,1.563 0.198,0.167 10 false *c 0.073,1 0.271,1.167 0.198,0.167 10 false *b 3.177,0.792 3.375,0.958 0.198,0.167 10 false *a 3.177,1 3.375,1.167 0.198,0.167 10 false *b 3.177,1.375 3.375,1.542 0.198,0.167 10 false *e 3.177,1.563 3.375,1.729 0.198,0.167 10 false *d

GPS Information

*a: Satellite Information Description
Display Content
No. Number of the target GPS satellite.
Elv Elevation angle of the target GPS satellite.
Azm Direction of the target GPS satellite
LVL The GPS signal level

*b: Receiving condition Description
Display Content
P The system is using the GPS signal for location.
T The system is tracking the GPS signal for location.
U The system is receiving a GPS signal, but is not using it for location.
- The system cannot receive a GPS signal. (Searching a GPS Signal)

*c: Measurement Status Description
Display Content
OK (H3D) High accuracy 3-dimensional location method is being used.
OK (H2D) High accuracy 2-dimensional location method is being used.
OK (3D) 3-dimensional location method is being used.
OK (2D) 2-dimensional location method is being used.
NG Location data cannot be used.
error Reception error has occurred.
- Any other state.

*d: Position Information Description
Display Content
Position Latitude and longitude information on the current position is displayed.

*e: Date information Description
Display Content
Date The date/time information obtained from GPS signals is displayed in Greenwich Mean Time (GMT).

HINT:
·

This screen is updated once per second.

·

Information from a maximum of 12 satellites is displayed on the screen.



i.

When the "GPS Information" screen is displayed, check the GPS conditions.



e.

Select "Sensors Check" from the "GPS Information" screen.


f.
E226261N03
2.865,0.958 3.094,0.958 false 2.865,1.26 3.094,1.26 false 3.156,0.875 3.354,1.042 0.198,0.167 10 false *a 3.156,1.177 3.354,1.344 0.198,0.167 10 false *b

Vehicle Sensors

Screen Description
Display Content
*a: Vehicle signal Vehicle speed signal condition is displayed.
*b: Sensor signal Gyro sensor output condition is displayed.

HINT:

This screen is updated once per second.


i.

Check all the signals and sensors when vehicle signal information is displayed.




CHECK VEHICLE SIGNAL


HINT:
·

Vehicle signals received by the navigation receiver assembly are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E225783

Select "Vehicle Signal" from the "Function Check/Setting I" screen.


d.
E225776

Vehicle Signal Check Mode

Screen Description
Display Content
Battery Auxiliary battery voltage is displayed.
IG Power switch ON/OFF state is displayed.
PKB Parking brake ON/OFF state is displayed.
REV Reverse signal ON/OFF state is displayed.
SPEED Vehicle speed is displayed in km/h.
TAIL Tail signal (Light control switch) ON/OFF state is displayed.
ADIM/TCAN Brightness state DIM (with) / BRIGHT (without) is displayed.

HINT:
·

Only items sending vehicle signals will be displayed.

·

This screen displays vehicle signals input to the navigation receiver assembly.

·

This screen is updated once per second when vehicle input signals change.



i.

When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.




CHECK HANDS-FREE VOICE QUALITY AND VOLUME SETTING


NOTICE:
·

Adjustment of the settings is required for each registered cellular phone.

·

If no cellular phone has been registered, all switches cannot be selected.



HINT:
·

The hands-free volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E225784

Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.


d.
E267557N01
0.323,0.802 0.542,0.802 false 0.323,1.073 0.542,1.073 false 0.135,0.958 0.365,1.156 0.229,0.198 10 false *b 0.125,0.688 0.354,0.885 0.229,0.198 10 false *a

Hands-Free Voice Quality Setting (Receive/Send Voice Level adjustment)

Screen Description
Display Content
*a: Receive voice level adjustment Setting for the voice level received from "Bluetooth" compatible phones.
*b: Send voice level adjustment Setting for the voice level sent from "Bluetooth" compatible phones.

NOTICE:

Sound quality may deteriorate when the receive voice or send voice level is changed more than necessary. For this reason, check that the received voice or sent voice quality is still acceptable after changing this setting.


i.

If the voice level is low, press the up button, and if the voice level is loud, press the down button.

HINT:
·

Settings will be applied when the up or down button is selected.

·

The received voice level adjustment ranges from -5 to +1.

·

The sent voice level adjustment ranges from -5 to +4.

·

The initial level is "0".





e.
E267558C01
2.885,0.948 3.104,0.948 false 1.792,1.74 1.792,1.917 false 2.854,1.656 3.104,1.656 false 3.115,0.823 3.344,1.01 0.229,0.188 10 false *a 3.115,1.542 3.344,1.729 0.229,0.188 10 false *b 1.719,1.927 1.948,2.115 0.229,0.188 10 false *c
*a Numeric keypad
*b Setting button
*c Reset button


Hands-Free Voice Quality Setting (Voice Quality Type adjustment)

i.

If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.


ii.

When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

Settings
Parameter Target Phenomenon Voice Quality Type Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality
A
(Noise)
The change in background noise the other party hears becomes unpleasant. 1000 The change in background noise the other party hears is reduced. Background noise when not talking becomes large.
B
(Noise)
The volume of the noise the other party hears temporarily becomes large. 2000 The temporary noise is reduced. The volume of voice may drop temporarily.
C
(Echo)
The other party hears weak echoes. 0100 The amount of echo is reduced (low level). Sound quality of the other party deteriorates (low level).
D
(Echo)
The other party hears strong echoes. 0200 The amount of echo is reduced (high level). Sound quality of the other party deteriorates (high level).
E
(Quality)
The other party hears harsh noises. 0010 Sound the other party hears becomes soft. Sound the other party hears becomes muffled.
F
(Quality)
You hear harsh noises. 0020 Sound you hear becomes soft. Sound you hear becomes muffled.

Settings (When multiple phenomenon occurred)
Parameter Target Phenomenon Voice Quality Type Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality
A+C The change in background noise the other party hears becomes unpleasant and the other party hears weak echoes. 1100
·

The change in background noise the other party hears is reduced.

·

The amount of echo is reduced (low level).


·

Background noise when not talking becomes large.

·

Sound quality of the other party deteriorates (low level).


A+D The change in background noise the other party hears becomes unpleasant and the other party hears strong echoes. 1200
·

The change in background noise the other party hears is reduced.

·

The amount of echo is reduced (high level).


·

Background noise when not talking becomes large.

·

Sound quality of the other party deteriorates (high level).


B+C The volume of the noise the other party hears temporarily becomes large and the other party hears weak echoes. 2100
·

The temporary noise is reduced.

·

The amount of echo is reduced (low level).


·

The volume of voice may drop temporarily.

·

Sound quality of the other party deteriorates (low level).


B+D The volume of the noise the other party hears temporarily becomes large and the other party hears strong echoes. 2200
·

The temporary noise is reduced.

·

The amount of echo is reduced (high level).


·

The volume of voice may drop temporarily.

·

Sound quality of the other party deteriorates (high level).


C+E The other party hears weak echoes and harsh noises. 0110
·

The amount of echo is reduced (low level).

·

Sound the other party hears becomes soft.


·

Sound quality of the other party deteriorates (low level).

·

Sound the other party hears becomes muffled.


C+F The other party hears weak echoes and you hear harsh noises. 0120
·

The amount of echo is reduced (low level).

·

Sound you hear becomes soft.


·

Sound quality of the other party deteriorates (low level).

·

Sound you hear becomes muffled.



HINT:
·

The default value is "0000".

·

Settings will be applied when the setting button is selected.

·

If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.

·

If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by pressing the "INIT" switch.






CHECK DAB RECEPTION


HINT:
·

The reception condition of DAB (Digital Audio Broadcast) can be checked.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E225777

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E235730

Select "Next Page" from the "Function Check/Setting I" screen.


d.
E235721

Select "DAB Reception Check" from the "Function Check/Setting II" screen.


e.
E245217N02
0.333,0.875 0.531,0.875 false 1.719,0.875 2.083,0.875 false 2.688,1.208 3.052,1.208 false 2.688,1.354 3.052,1.354 false 0.156,0.802 0.469,1 0.313,0.198 10 false *a 2.125,0.781 2.438,0.979 0.313,0.198 10 false *b 3.094,1.125 3.406,1.323 0.313,0.198 10 false *c 3.094,1.292 3.406,1.49 0.313,0.198 10 false *d

Select "DAB Reception Check" from the "Function Check/Setting II" screen.

*a: Channel Change Switch Description
Display Content
Up or down button Enables the channel to be changed to the one to be checked.

*b: Check Switch Description
Display Condition Content
Check Before/after check Starts checking
STOP During check Stops checking

*c: Antenna Connection Check Result Description
Display Content
OK Connected properly
NG Not connected properly
- Not equipped with DAB antenna.

*d: DAB Tuner Reception Level Check Result Description
Display Content
Black Good reception
Red Poor reception
- Not equipped with DAB antenna.

i.

Select "CHECK" button to start the DAB reception check.


ii.

Check that the result is displayed when the DAB reception check is performed.




CLEAR PASSWORD OF EXPORT/IMPORT MEMORY POINT FUNCTION


HINT:
·

This function allows the initialization of a password which was set on the navigation ECU sub-assembly when exporting/importing memory points.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E229432

Select "Service Information" from the "Service Menu" screen.


c.
E235719

Select "Memory point backup" from the "Service Information" screen.


d.
E235720

Clear backup password

HINT:

Depending on the manufacturer, some component names and versions will be displayed differently.


i.

Select "Clear backup password".




CHECK SOFTWARE ERROR HISTORY


HINT:

This function is used to check the cause when the navigation ECU sub-assembly screen is blacked out.


a.

Check software error history.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the power switch on (READY).


iii.

Turn the intelligent tester on.


iv.

Enter the following menus: Body / Navigation System / Utility / Software Error History.

Body Electrical > Navigation System > Utility
Tester Display
Software Error History
50005 212 4150

v.

When an item is stored for Software Error History, record it before repairing the navigation ECU sub-assembly.

Software Error History Screen Description
Error Description Trigger Detail
Software Reset Navi Microcomputer Hexadecimal Number
Audio Microcomputer
CAN Microcomputer
No Video Signal Front Monitor
Rear Monitor
MOST Cold Restart Always

HINT:
·

Software Error History can store up to 5 history data items. If a new software error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.

·

If an error that is unsupported by the intelligent tester occurs, a "-" is displayed for the display items.





b.

Clear software error history.

i.

When DTCs are cleared using any of the following operations, Software Error History will be cleared as well (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for HDD)>DTC CHECK / CLEAR).

·

Cleared using the intelligent tester.

·

Cleared using the system check mode screen.

·

Cleared using the unit check mode screen.





CHECK OPTICAL DISC ERROR HISTORY


HINT:

This function is used to check the cause when an optical disc error occurs.


a.

Check optical disc error history.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the power switch on (READY).


iii.

Turn the intelligent tester on.


iv.

Enter the following menus: Body / Navigation System / Utility / Optical Disc Error History.

Body Electrical > Navigation System > Utility
Tester Display
Optical Disc Error History
50005 212 4151

v.

When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.

Optical Disc Error History Screen Description
Display Content
Error Type Displays the type of error.
Device Displays the malfunctioning device.
Date Displays the date and time that the malfunction occurred.

"Error Type" Screen Description
Error Type Detection Condition Action
Read Error When a disc read error occurs. Proceed to next suspected area shown in Problem Symptoms Table (See page (Click here))
Disc damaged/up side down/dirty When it is determined that any of the following is the cause of the disc read error:
·

The disc cannot be read.

·

The disc cannot be read because of dirt or scratches.

·

The disc cannot be read because it is inserted upside down.


Cannot determine disc type An unsuitable disc is inserted.
DPS error When an error occurs while decoding MP3/WMA files.
Some files are corrupt
·

When MP3/WMA files cannot be played back because they are unsupported.

·

Even though the file extensions are MP3 or WMA, files cannot be played back because the header information cannot be read.


Some files cannot be found
·

When a disc without music data is played back.

·

When there are no playable MP3/WMA files.


Copy protection violation When a file with copyright protection that cannot be played back is played back.

"Device" Screen Description
Device Component
DVD-P Navigation ECU sub-assembly
CD-P Not available
R-Seat DVD-P Not available

HINT:
·

Optical Disc Error History can store up to 7 history data items. If a new optical disc error occurs when 7 data items have already been stored, the oldest data is cleared and the new data is stored.

·

If an error that is unsupported by the intelligent tester occurs, a "-" or blank is displayed for the display items.





b.

Clear optical disc error history.

i.

When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for HDD)>DTC CHECK / CLEAR).

·

Cleared using the intelligent tester.

·

Cleared using the system check mode screen.

·

Cleared using the unit check mode screen.





MAP INFORMATION


HINT:

This function is used to check the map version of the navigation system and the end date of the map update service.


a.

Check map information.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the power switch on (READY).


iii.

Turn the intelligent tester on.


iv.

Enter the following menus: Body / Navigation System / Utility / Map Information.

Body Electrical > Navigation System > Utility
Tester Display
Map Information
50005 212 4265

v.

Check the map version and the end date of the map update service.