Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR › from 2015.04
RM2040EQ _59 Vehicle Exterior _014737 WIPER / WASHER _0075168 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Connect the connector.


c.

Turn the power switch on (IG).


d.

Operate the wiper and stop the windshield wiper motor assembly at the automatic stop position.


e.

Turn the power switch off.


f.

Disconnect the connector.


g.
E230753C02
1.979,1.354 2.115,1.354 false 2.146,1.24 2.698,1.604 0.552,0.365 10 false *a
*a Pivot of the windshield wiper motor assembly


Apply MP grease to the pivot of the windshield wiper motor assembly.


h.
E230060C02
2.083,0.406 1.417,0.406 false 1.438,0.844 0.865,0.844 false 1.219,0.302 1.615,0.521 0.396,0.219 10 false *1 0.677,0.719 0.969,0.99 0.292,0.271 10 false *a
*1 No. 1 Rod
*a Pivot of the windshield wiper motor assembly


Connect the No. 1 rod to the pivot of the windshield wiper motor assembly.


Hide 2.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

a.
E227509C04
0.99,2.677 1.698,2.792 false 1.75,2.698 2.073,2.99 0.323,0.292 10 false *1
*1 Motor Grommet


Engage the motor grommet as shown in the illustration.

NOTICE:

Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.



b.

Install the windshield wiper motor and link assembly with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


c.

Connect the connector and then engage the 2 clamps.


Hide 55781E 3.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Engage the 8 guides as shown in the illustration.

E230067


b.

Engage the 6 claws and guide to install the cowl top ventilator louver sub-assembly.

E230058


Hide 53866J 4.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

a.
E314401

Engage the guide and 2 clips to install the front fender to cowl side seal RH as shown in the illustration.


Hide 53867H 5.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

HINT:

Use the same procedure as for the RH side.


Hide 6.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.
E226523C13
1.052,1.125 0.229,1.125 false 0.073,1.031 0.427,1.281 0.354,0.25 10 *a
*a Wiper Arm Serration


When reusing the front wiper arm and blade assembly RH:

i.

Clean the wiper arm serrations.

NOTICE:

Do not grind down the wiper arm serrations.




b.
E231343C13
1.958,1.104 2.26,1.104 false 2.292,0.99 2.604,1.229 0.313,0.24 10 *a
*a Wiper Pivot Serration


When reusing the windshield wiper link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.

Operate the wiper and stop the windshield wiper motor assembly at the automatic stop position.


d.
E230908C03
2.167,1.052 2.167,1.583 false 2.115,1.604 2.49,1.938 0.375,0.333 10 false *1 2.615,0.74 2.854,1 0.24,0.26 10 false A 2.604,1.188 2.917,1.417 0.313,0.229 10 false A
*1 Ceramic Dot


Set the front wiper arm and blade assembly RH in the range shown in the illustration and then install the front wiper arm and blade assembly RH with the nut.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

Area Measurement
A 7.5 mm (0.295 in.)

HINT:

Hold the wiper arm by hand while tightening the nut.



Hide 7.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.
E226523C14
1.052,1.125 0.229,1.125 false 0.073,1.031 0.427,1.281 0.354,0.25 10 *a
*a Wiper Arm Serration


When reusing the front wiper arm and blade assembly LH:

i.

Clean the wiper arm serrations.

NOTICE:

Do not grind down the wiper arm serrations.




b.
E231343C14
1.958,1.104 2.26,1.104 false 2.292,0.99 2.604,1.229 0.313,0.24 10 *a
*a Wiper Pivot Serration


When reusing the windshield wiper link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.
E230909C03
2.333,0.885 2.333,1.104 false 2.729,0.906 3.052,1.177 0.323,0.271 10 false A 2.729,0.438 3,0.677 0.271,0.24 10 false A 2.25,1.104 2.615,1.406 0.365,0.302 10 false *1
*1 Ceramic Dot


Set the front wiper arm and blade assembly LH in the range shown in the illustration and then install the front wiper arm and blade assembly LH with the nut.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

Area Measurement
A 7.5 mm (0.295 in.)

HINT:

Hold the wiper arm by hand while tightening the nut.



d.

Turn the power switch on (IG).


e.

Operate the windshield wipers while spraying washer fluid onto the windshield glass. Make sure that the windshield wipers function properly and the wipers do not come into contact with the vehicle body.


f.

Lift each wiper arm twice after the wipers stop and check the wiper set position.


g.

Turn the power switch off.