Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014700 CRUISE CONTROL _0166042 DYNAMIC RADAR CRUISE CONTROL SYSTEM U

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  TERMINALS OF ECU  


CHECK DRIVING SUPPORT ECU ASSEMBLY


E158948E49
3.458,0.208 3.823,0.448 0.365,0.24 3.531,0.26 3.927,0.51 0.396,0.25 10 false I176

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I176-6 (SPSW) - I176-25 (GND) R - W-B Steering pad switch signal
(distance control signal)
Power switch on (IG),
Distance control switch off
10 to 14 V
I176-6 (SPSW) - I176-25 (GND) R - W-B Steering pad switch signal
(distance control signal)
Power switch on (IG),
Distance control switch on
6 to 7 V
I176-10 (CCHG) - I176-25 (GND) GR - W-B Cruise control main switch signal Power switch on (IG),
MODE switch off
10 to 14 V
I176-10 (CCHG) - I176-25 (GND) GR - W-B Cruise control main switch signal Power switch on (IG),
MODE switch on
Below 1 V
I176-17 (CA2L) - I176-25 (GND) LG - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
I176-18 (CA1N) - I176-25 (GND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
I176-23 (CCS) - I176-25 (GND) W - W-B Cruise control main switch signal Power switch on (IG) 11 to 14 V
I176-23 (CCS) - I176-25 (GND) W - W-B Cruise control main switch signal Power switch on (IG),
CANCEL switch on
6.6 to 10.1 V
I176-23 (CCS) - I176-25 (GND) W - W-B Cruise control main switch signal Power switch on (IG),
-SET switch on
4.5 to 7.1 V
I176-23 (CCS) - I176-25 (GND) W - W-B Cruise control main switch signal Power switch on (IG),
+RES switch on
2.3 to 4.0 V
I176-23 (CCS) - I176-25 (GND) W - W-B Cruise control main switch signal Power switch on (IG),
Main switch on
Below 1 V
I176-25 (GND) - Body ground W-B - Body ground Earth (ground circuit of driving support ECU) Always Below 1 Ω
I176-27 (STP) - I176-25 (GND) GR - W-B Stop light signal Brake pedal released Below 1 V
I176-27 (STP) - I176-25 (GND) GR - W-B Stop light signal Brake pedal depressed 11 to 14 V
I176-28 (ST1-) - I176-25 (GND) R - W-B Stop light signal Power switch on (IG),
Brake pedal released
11 to 14 V
I176-28 (ST1-) - I176-25 (GND) R - W-B Stop light signal Power switch on (IG),
Brake pedal depressed
Below 1 V
I176-30 (B) - I176-25 (GND) V - W-B Power source Power switch on (IG) 11 to 14 V
I176-32 (WIP2) - I176-25 (GND) V - W-B Wiper switch signal Power switch on (IG),
Wiper switch off
Below 1 V
I176-32 (WIP2) - I176-25 (GND) V - W-B Wiper switch signal Power switch on (IG),
Wiper switch LO position
6 to 7 V
I176-32 (WIP2) - I176-25 (GND) V - W-B Wiper switch signal Power switch on (IG),
Wiper switch HI position
11 to 14 V
I176-39 (CA2H) - I176-25 (GND) L - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
I176-40 (CA1P) - I176-25 (GND) LG - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)

a.
A306760E01
1.323,1.854 2.313,2.146 0.99,0.292 10 false 10 μsec./DIV. 3.01,1.375 3.354,1.573 0.344,0.198 10 false GND 2.781,0.24 3.427,0.563 0.646,0.323 10 false 1 V/DIV.

WAVEFORM 1

i.

CAN communication signal

Terminal Name Between I176-17 (CA2L) and I176-25 (GND)
Between I176-40 (CA1P) and I176-25 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




b.
A306761E01
1.333,1.885 2.354,2.156 1.021,0.271 10 false 10 μsec./DIV. 2.75,0.302 3.365,0.521 0.615,0.219 10 false 1 V/DIV. 3,1.406 3.406,1.604 0.406,0.198 10 false GND

WAVEFORM 2

i.

CAN communication signal

Terminal Name Between I176-18 (CA1N) and I176-25 (GND)
Between I176-39 (CA2H) and I176-25 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.