DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Radar Cruise / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Cruise Control Main Switch | Cruise control switch signal | ON or OFF | ON: Cruise control main switch pushed
OFF: Cruise control main switch released |
- |
| RES/ACC Switch | +/RES switch signal | ON or OFF | ON: +/RES switch on
OFF: +/RES switch off |
- |
| SET/COAST Switch | -/SET switch signal | ON or OFF | ON: -/SET switch on
OFF: -/SET switch off |
- |
| Distance Control Switch | Distance control switch signal | ON or OFF | ON: Distance control switch on
OFF: Distance control switch off |
- |
| Cruise Control | Cruise control system operation signal | ON or OFF | ON: Cruise control system operating
OFF: Cruise control system not operating |
- |
| Constant Speed Mode | Constant speed mode signal | ON or OFF | ON: Dynamic radar cruise control system is in constant speed mode
OFF: Dynamic radar cruise control system is in vehicle-to-vehicle distance control mode |
- |
| Cruise Control Mode | Cruise control mode signal | All Spd, Hi Spd or Normal | All Spd: Vehicle-to-vehicle distance control mode (w/ full-speed following function)
Hi Spd: Vehicle-to-vehicle distance control mode (w/o full-speed following function) Normal: Constant speed mode |
- |
| CCS Mem Vehicle Spd | Cruise control memorized speed | min.: 0 km/h (0 mph), max.: 320 km/h (199 mph) | Memorized speed: Cruise control activated | - |
| Vehicle Distance | Distance to preceding vehicle | min.: 0 m (0 ft.), max.: 255 m (836.65 ft.) | Actual distance to vehicle | - |
| Stop Light SW 1 (M CPU) | Stop light switch (Main-CPU) signal | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Stop Light SW 1 (S CPU) | Stop light switch (Sub-CPU) signal | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Stop Light SW 2 (M CPU) | Stop light switch (Main-CPU) signal | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Wiper (Hi) | Windshield wiper switch Hi signal | ON or OFF | ON: Windshield wiper switch Hi position
OFF: Windshield wiper switch except Hi position |
- |
| Wiper (Lo) | Windshield wiper switch Lo signal | ON or OFF | ON: Windshield wiper switch Lo position
OFF: Windshield wiper switch except Lo position |
- |
| Tail Light | Tail light switch signal | ON or OFF | ON: Tail light switch on
OFF: Tail light switch off |
- |
| Vhcl Spd Calc-Whl Spd | Vehicle speed | min.: -327 km/h (-203 mph), max.: 327 km/h (204 mph) | Actual vehicle speed | - |
| Vhcl Spd-Brake ECU | Vehicle speed | min.: -327 km/h (-203 mph), max.: 327 km/h (204 mph) | Actual vehicle speed | - |
| Invalid Whl Spd Sens Num | Invalid wheel speed sensor | min.: 0, max.: 255 | Actual invalid wheel speed sensor | - |
| Rear Whl Spd LH Sensor | Rear speed sensor LH signal | Normal or Abnoml | Normal: Rear speed sensor LH is normal
Abnoml: Rear speed sensor LH is abnormal |
- |
| Rear Whl Spd RH Sensor | Rear speed sensor RH signal | Normal or Abnoml | Normal: Rear speed sensor RH is normal
Abnoml: Rear speed sensor RH is abnormal |
- |
| Front Whl Spd LH Sensor | Front speed sensor LH signal | Normal or Abnoml | Normal: Front speed sensor LH is normal
Abnoml: Front speed sensor LH is abnormal |
- |
| Front Whl Spd RH Sensor | Front speed sensor RH signal | Normal or Abnoml | Normal: Front speed sensor RH is normal
Abnoml: Front speed sensor RH is abnormal |
- |
| Vehicle Acceleration | Vehicle acceleration | min.: -5 m/s2, max.: 5 m/s2 | Actual vehicle acceleration | - |
| Whl Spd/Deceleration Sen | Wheel speed sensor/Deceleration sensor signal | Avail or Not Avl | Avail: Wheel speed sensor/Deceleration sensor available
Not Avail: Wheel speed sensor/Deceleration sensor not available |
- |
| Closed Throttle Position | Accelerator pedal idle position signal | ON or OFF | ON: Accelerator pedal released
OFF: Accelerator pedal depressed |
- |
| Yaw Rate Sensor | Yaw rate value | min.: -100 deg/s, max.: 100 deg/s | Actual yaw rate value | - |
| Deceleration Sensor 1 | Deceleration value | min.: -14.7 m/s2, max.: 14.7 m/s2 | Actual deceleration value | - |
| Deceleration Sensor 2 | Deceleration value | min.: -14.7 m/s2, max.: 14.7 m/s2 | Actual deceleration value | - |
| Tar Accel for All Spd | Target acceleration speed for following function | min.: -5.12 m/s2, max.: 5.08 m/s2 | Actual target vehicle acceleration | - |
| Tar Accel for ACC | Target vehicle acceleration for vehicle-to-vehicle distance control mode | min.: -5.12 m/s2, max.: 5.08 m/s2 | Actual target vehicle acceleration | - |
| Tar Accel for CCS | Target vehicle acceleration for constant speed mode | min.: -5.12 m/s2, max.: 5.08 m/s2 | Actual target vehicle acceleration | - |
| Request Driving Force | Cruise control system request drive force | min.: -65536 N, max.: 65534 N | Actual request drive force | - |
| ECM/PCM Command | Origin of the drive force request | Pedal, None or DS | Pedal: Accelerator pedal depressed
None: drive force not requested DS: Radar cruise control system operating |
- |
| Max Val of Available DF | Maximum value of available drive force | min.: -65536 N, max.: 65534 N | Actual available drive force maximum value | - |
| Min Val of Available DF | Minimum value of available drive force | min.: -65536 N, max.: 65534 N | Actual available drive force minimum value | - |
| Forward Vhcl Relative Spd | Vehicle ahead relative speed | min.: -128 m/s, max.: 127 m/s | Actual vehicle ahead relative speed | - |
| Vehicle Approach Warning | Forward vehicle approach warning signal | ON or OFF | ON: Forward vehicle approaching
OFF: Forward vehicle not approaching |
- |
| Vhcl Stability Ctrl Buzz | Skid control buzzer operation signal | ON or OFF | ON: Skid control buzzer operating
OFF: Skid control buzzer not operating |
- |
| Brk Rqst to Elec Ctrl Brk | Braking request to brake control | NotCtrl, None, Exist, None, Exist or Disable | NotCtrl: Not operating
None: No control request, no coordinated shifting Exist: Control request, no coordinated shifting None: No control request, coordinated shifting Exist: Control request, coordinated shifting Disable: Data invalid |
- |
| Brk Rqst to Shift Down | Braking request to AT control | NotCtrl, None, Exist, None, Exist or Disable | NotCtrl: Not operating
None: No control request, no coordinated shifting Exist: Control request, no coordinated shifting None: No control request, coordinated shifting Exist: Control request, coordinated shifting Disable: Data invalid |
- |
| Operator Override | Operator override | NotCtrl, Able, Able, Unable or Disable | NotCtrl: Not operating
Able: Override possible, brake assist control not being performed Able: Override possible, brake assist control being performed Unable: Override not possible Disable: Data invalid |
- |
| Forward Vehicle Detect | Vehicle ahead detection signal | Detect or No Dtct | Detect: Vehicle ahead detected
No Dtct: Vehicle ahead not detected |
- |
| CCS Main SW-Ready | Dynamic radar cruise control system standby condition | ON or OFF | ON: Dynamic radar cruise control system standby
OFF: Dynamic radar cruise control system not standby |
- |
| CCS System Check | Dynamic radar cruise control system warning indication | ON or OFF | ON: Dynamic radar cruise control system warning indication (Malfunction detected)
OFF: Dynamic radar cruise control system warning indication (Malfunction not detected) |
- |
| FRS-Dirt | History of dirt detected on millimeter wave radar sensor assembly | ON or OFF | ON: History of dirt detected on millimeter wave radar sensor assembly
OFF: No history of dirt detected on millimeter wave radar sensor assembly |
- |
| Bad Wthr Hist(F Radar Sen) | History of millimeter wave radar sensor assembly detecting bad weather | ON or OFF | ON: History of millimeter wave radar sensor assembly detecting bad weather
OFF: No history of millimeter wave radar sensor assembly detecting bad weather |
- |
| Frnt Radar Sens Temp Hi | Millimeter wave radar sensor assembly high temperature abnormality | ON or OFF | ON: Millimeter wave radar sensor assembly abnormal
OFF: Millimeter wave radar sensor assembly normal |
- |
| Front Radar Voltage | Millimeter wave radar sensor assembly low voltage abnormality | ON or OFF | ON: Millimeter wave radar sensor assembly abnormal
OFF: Millimeter wave radar sensor assembly normal |
- |
| CCS Cancel by Low Spd | Dynamic radar cruise control system (constant speed mode) low speed cancel signal | ON or OFF | ON: Low speed cancel signal on
OFF: Low speed cancel signal off |
- |
| Cancl CCS by Com Delay | Dynamic radar cruise control system (constant speed mode) cancel signal | ON or OFF | ON: Cancel signal on
OFF: Cancel signal off |
- |
| Cancl CCS by RAM Malfnc | Dynamic radar cruise control system (constant speed mode) cancel signal | ON or OFF | ON: Cancel signal on
OFF: Cancel signal off |
- |
| A-CCS Cancl-Radar/Wip | Dynamic radar cruise control system (vehicle-to-vehicle distance control mode) cancel signal | ON or OFF | ON: Cancel signal on
OFF: Cancel signal off |
- |
| A-CCS Cancl-ORC Malf | Brake hold system malfunction condition | ON or OFF | ON: Malfunctioning
OFF: Normal |
- |
| A-CCS Cancl-ORC | Brake hold system malfunction condition | ON or OFF | ON: Normal
OFF: Malfunctioning |
- |
| A-CCS Cancl-Logical Err | Logic malfunction condition between brakes and driving support ECU assembly | ON or OFF | ON: Malfunctioning
OFF: Normal |
- |
| Country# (F Radar Sens) | Destination country for millimeter wave radar sensor assembly | JPN, NA, EURO, CA, AUS, SAFC, OTHER, TWN, CHINA, THAI, GCC or NOFIX | Actual country code | - |
| Steering Angle | Steering angle | min.: -3072 deg, max.: 3070.5 deg | 0.0 deg is displayed when steering wheel is centered. | - |
| Zero Point Angle Sens | Zero point steering angle sensor | min.: -3072 deg, max.: 3070.5 deg | Actual zero point steering angle | - |
| Radar | Millimeter wave radar sensor assembly operation signal | Emission or Stop | Emission: Millimeter wave radar sensor assembly signal sent
Stop: Millimeter wave radar sensor assembly signal stopped |
- |
| # Codes | Number of DTCs | min.: 0, max.: 255 | Actual number of DTCs | - |
Enter the following menus: Body Electrical / Pre-Crash 2 / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Country# (DSS) | Destination country for driving support ECU assembly | JPN, NA, EURO, CA, AUS, SAFC, OTHER, TWN, CHINA, THAI, GCC or NOFIX | Actual country code | - |
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light SW | Stop light switch assembly | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Stop Light Relay Output | Stop light switch assembly (stop light relay) | ON or OFF | ON: Relay output on (Stop light on)
OFF: Relay output off (Stop light off) |
- |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Perform Active Test according to the display on the GTS.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.
Perform the Active Test according to the display on the GTS.
The power switch must be turned on (IG) to proceed with the Active Test using the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Radar Cruise Approach Alarm Buzzer | Skid control buzzer | ON or OFF | Buzzer can be heard |
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Perform the Active Test according to the display on the GTS.
The power switch must be turned on (IG) to proceed with the Active Test using the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Meter Display 1 | Multi-information display | OFF or All | - |
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
Perform the Active Test according to the display on the GTS.
The power switch must be turned on (IG) to proceed with the Active Test using the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Stop Light Relay | Stop light switch assembly (stop light relay) | ON or OFF | Stop lights come on |