Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014700 CRUISE CONTROL _0166042 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  C1A11  Front Radar Sensor Incorrect Axial Gap  C1A14  Front Radar Sensor Beam Axis Not Adjusted  


DESCRIPTION

The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle.

Based on this information, the driving support ECU assembly sends pre-crash safety control operation signals.

When the vehicle is determined to be driving in a straight line or on a gradual curve based on signals from the airbag sensor assembly (yaw rate sensor), the millimeter wave radar sensor assembly performs self diagnosis to check if the sensor beam axis is deviated from the vehicle movement direction.

When the millimeter wave radar sensor assembly beam axis is not adjusted correctly, the driving support ECU assembly detects this, and DTC C1A11 is stored.

After installing a new millimeter wave radar sensor assembly, if sensor beam axis adjustment is not performed, DTC C1A14 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A11 Front Radar Sensor Incorrect Axial Gap When the power switch is on (IG), a deviation in the millimeter wave radar sensor assembly beam axis is detected for 0.272 seconds or more while the vehicle is being driven at a speed of 36 km/h (22 mph) or more.
·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly


C1A14 Front Radar Sensor Beam Axis Not Adjusted When the vehicle is being driven at a speed of 36 km/h (22 mph) or more, incompletion of sensor beam axis adjustment is detected for 0.272 seconds or more.
·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

Check that the millimeter wave radar sensor assembly has not been replaced with one from another vehicle.

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Check that the bracket of the millimeter wave radar sensor assembly is not deformed.

HINT:

If the bracket is deformed, replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL



b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTCS (DTC C1A11 OR C1A14)
2.CHECK FOR DTCS (DTC C1A11 OR C1A14)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Clear DTCs
50002 197

e.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which dynamic radar cruise control system operation is possible.


ii.

Turn the cruise control system on using the cruise control main switch (ON-OFF button).


iii.

Push the cruise control main switch to -/SET to begin control of vehicle speed using the cruise control system.



f.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A11 and C1A14 are not output A
DTC C1A11 or C1A14 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

3.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
3.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Adjust the front millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCS (DTC C1A11 OR C1A14)
4.CHECK FOR DTCS (DTC C1A11 OR C1A14)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Clear DTCs
50002 197

e.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which dynamic radar cruise control system operation is possible.


ii.

Turn the cruise control system on using the cruise control main switch (ON-OFF button).


iii.

Push the cruise control main switch to -/SET to begin control of vehicle speed using the cruise control system.



f.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A11 and C1A14 are not output A
DTC C1A11 or C1A14 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY