Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014700 CRUISE CONTROL _0166042 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  C1A4B  Stop Light Relay Circuit  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) sends a stop light operation signal to the stop light switch assembly. When the skid control ECU (brake booster with master cylinder assembly) detects a malfunction in the stop light circuit, the driving support ECU assembly stores DTC C1A4B.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4B Stop Light Relay Circuit Either of the following conditions is met:
·

When the power switch is on (IG), the IG1 terminal voltage is between 11 and 14 V and the stop light illumination output signal (STPO) is output, the signal is not received at terminal STP2 for 0.272 seconds or more while the vehicle is being driven at a speed of 36 km/h (22 mph) or more.

·

When the power switch is on (IG), the IG1 terminal voltage is between 11 and 14 V and the stop light illumination output signal (STPO) is not output, the signals received at terminals STP and STP2 are different for 0.272 seconds or more while the vehicle is being driven at a speed of 36 km/h (22 mph) or more.


·

Lighting system

·

Electronically controlled brake system

·

Harness or connector

·

Driving support ECU assembly

·

Stop relay



WIRING DIAGRAM

B381524E16
1.927,0.469 3.302,0.729 1.375,0.26 10 false from DC/DC Fuse 4.49,0.24 6.635,0.448 2.146,0.208 10 false from Stop Light Switch Assembly 0.708,0.646 1.333,0.948 0.625,0.302 10 false STOP 1.344,1.667 1.573,1.875 0.229,0.208 10 false 5 1.333,2.229 1.563,2.438 0.229,0.208 10 false 2 2.521,1.208 2.75,1.417 0.229,0.208 10 false 4 2.521,1.688 2.75,1.896 0.229,0.208 10 false 3 2.521,2.229 2.75,2.438 0.229,0.208 10 false 1 5.417,1.208 5.646,1.417 0.229,0.208 10 false 33 5.49,1.688 5.719,1.896 0.229,0.208 10 false 6 5.479,2.229 5.708,2.438 0.229,0.208 10 false 3 1.833,2.792 2.458,3.094 0.625,0.302 10 false STOP 5.708,1.323 6.333,1.625 0.625,0.302 10 false STP 5.698,1.802 6.323,2.104 0.625,0.302 10 false STP2 5.708,2.354 6.333,2.656 0.625,0.302 10 false STPO 2.51,3.135 3.458,3.427 0.948,0.292 10 false to Stop Lights 1.917,3.458 3.677,3.865 1.76,0.406 10 false from IG1 NO. 2 Relay 0.479,3.615 1.594,3.896 1.115,0.281 10 false ECU-IG1 NO. 1 0.167,5.719 2.302,5.958 2.135,0.24 10 false Driving Support ECU Assembly 1.188,6.323 3.521,6.76 2.333,0.438 10 false : CAN Communication Line 5.115,5.719 5.448,5.927 0.333,0.208 10 false A28 5.094,5.875 7.135,6.271 2.042,0.396 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When this DTC is output, a malfunction in the lighting system is suspected. Check if the lighting system is functioning normally.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the driving support ECU assembly, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle, and as a result, a DTC may be stored.



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STOP RELAY POWER SOURCE)

NG

2.CHECK HARNESS AND CONNECTOR (STOP RELAY POWER SOURCE)
a.
B381525C08
0.24,0.219 0.552,0.417 0.313,0.198 10 false *a
*a No. 2 Engine Room Relay Block Assembly (Relay Holder)


Remove the STOP relay from the No. 2 engine room relay block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay holder terminal 5 - Body ground Always 11 to 14 V
Relay holder terminal 2 - Body ground Engine switch on (IG) 11 to 14 V



c.

Reinstall the STOP relay to the No. 2 engine room relay block assembly.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C277552C03
1.51,0.729 1.917,1 0.406,0.271 1.01,2.885 1.229,2.885 1.229,2.885 1.552,2.146 true 0.302,0.229 0.615,0.427 0.313,0.198 10 false *a 1.594,0.781 1.906,0.979 0.313,0.198 10 false A28 0.708,2.813 1.021,3.01 0.313,0.198 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-33 (STP) - Body ground Stop light switch assembly on
(Brake pedal depressed)
11 to 14 V
A28-33 (STP) - Body ground Stop light switch assembly off
(Brake pedal released)
Below 1.5 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT VOLTAGE)
a.
B381525C09
0.24,0.219 0.552,0.417 0.313,0.198 10 false *a
*a No. 2 Engine Room Relay Block Assembly (Relay Holder)


Remove the STOP relay from the No. 2 engine room relay block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay holder terminal 4 - Body ground Stop light switch assembly on
(Brake pedal depressed)
11 to 14 V
Relay holder terminal 4 - Body ground Stop light switch assembly off
(Brake pedal released)
Below 2 V



c.

Reinstall the STOP relay to the No. 2 engine room relay block assembly.


Result:
Proceed to
OK
NG



OK

5.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)
a.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


b.

Perform the Active Test according to the display on the GTS.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light switch assembly (stop light relay) ON or OFF Stop lights come on
Chassis > ABS/VSC/TRC > Active Test
Active Test Display
Stop Light Relay
Data List Display
Stop Light Relay Output
50004 105 5 291

c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


d.

Check the stop light switch assembly (stop light control relay) operation using the Data List and stop light operation by performing an Active Test.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay Output Stop light switch assembly (stop light relay) ON or OFF ON: Relay output on (Stop light on)
OFF: Relay output off (Stop light off)
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light Relay Output
50003 105 291
Result:
Result Proceed to
Data List item changes between ON and OFF, but stop lights do not turn on A
Data List item changes between ON and OFF and stop lights turn on and off B




A

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU [BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY] - STOP LIGHT SWITCH ASSEMBLY)

B

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU [BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY] - STOP LIGHT SWITCH ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU [BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY] - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Remove the STOP relay from the No. 2 engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-3 (STPO) - Relay holder terminal 1 Always Below 1 Ω
A28-3 (STPO) or Relay holder terminal 1- Body ground Always 10 kΩ or higher



d.

Reinstall the STOP relay to the No. 2 engine room relay block assembly.


e.

Reconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU [BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY] - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU [BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY] - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Remove the STOP relay from the No. 2 engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay holder terminal 3 - A28-6 (STP2) Always Below 1 Ω
Relay holder terminal 3 or A28-6 (STP2) - Body ground Always 10 kΩ or higher



d.

Reinstall the STOP relay to the No. 2 engine room relay block assembly.


e.

Reconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C277552C04
1.51,0.729 1.917,1 0.406,0.271 1,2.906 1.219,2.906 1.219,2.906 1.656,1.76 true 0.302,0.229 0.615,0.427 0.313,0.198 10 false *a 1.594,0.781 1.906,0.979 0.313,0.198 10 false A28 0.635,2.823 1.125,3.021 0.49,0.198 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU [Brake Booster with Master Cylinder Assembly])


Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-6 (STP2) - Body ground Stop light switch assembly on
(Brake pedal depressed)
11 to 14 V
A28-6 (STP2) - Body ground Stop light switch assembly off
(Brake pedal released)
Below 1.5 V



c.

Reconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


Result:
Proceed to
OK
NG



OK

9.CHECK FOR DTCS (DTC C1A4B)

NG

9.CHECK FOR DTCS (DTC C1A4B)
a.

Turn the power switch off and wait for at least 2 minutes.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Clear DTCs
50002 197

f.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

·

Using the GTS, perform the Active Test "Stop Light Relay" with the power switch on (IG).




g.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A4B is not output A
DTC C1A4B is output B



A

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY