The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle. Based on this information, the driving support ECU assembly sends pre-crash safety control operation signals. These DTCs are stored when a communication malfunction occurs between the sensors and ECUs that detect crashes, or between ECUs that perform the pre-crash safety control.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U0125 | Lost Communication with Yaw Rate Sensor Module | When the power switch is on (IG), a communication error between the airbag sensor assembly and the driving support ECU assembly is detected for 0.772 seconds or more while the vehicle is being driven at a speed of 36 km/h (22 mph) or more. | ·
CAN communication system ·
Airbag sensor assembly ·
Driving support ECU assembly |
| U0126 | Lost Communication with Steering Angle Sensor Module | When the power switch is on (IG), a communication error between the steering angle sensor and the driving support ECU assembly is detected for 3.76 seconds or more. while the vehicle is being driven at a speed of 36 km/h (22 mph) or more. | ·
CAN communication system ·
Steering angle sensor ·
Driving support ECU assembly |
| U0129 | Lost Communication with Brake System Control Module | When the power switch is on (IG), a communication error between the skid control ECU (brake booster with master cylinder assembly) and the driving support ECU assembly is detected for 5.240 seconds or more while the vehicle is being driven at a speed of 36 km/h (22 mph) or more. | ·
Brake booster with master cylinder assembly (Skid control ECU) ·
CAN communication system ·
Driving support ECU assembly |
| U0293 | Lost Communication with Hybrid Vehicle Control System | When the power switch is on (IG), a communication error between the skid control ECU (brake booster with master cylinder assembly) or power management control ECU and driving support ECU assembly is detected for 3.808 seconds or more while the vehicle is being driven at a speed of 36 km/h (22 mph) or more. | ·
CAN communication system ·
Power management control ECU ·
Driving support ECU assembly ·
Skid control ECU (Brake booster with master cylinder assembly) |
| U1104 | Lost Communication with Driving Support ECU | When the power switch is on (IG), a communication error between the power management control ECU or skid control ECU (brake booster with master cylinder assembly) and the driving support ECU assembly is detected for 1.016 seconds. | ·
CAN communication system ·
Power management control ECU ·
Skid control ECU (Brake booster with master cylinder assembly) ·
Driving support ECU assembly |
When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.
Check that the millimeter wave radar sensor assembly has not been replaced with one from another vehicle.
When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output | A |
| CAN communication system DTCs are output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING