Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014700 CRUISE CONTROL _0166042 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  U1104  Lost Communication with Driving Support ECU  


DESCRIPTION

The millimeter wave radar sensor assembly and driving support ECU assembly transmit the data for general vehicle control and diagnosis function via CAN communication line.

The millimeter wave radar sensor assembly transmits information about the vehicle in front to the driving support ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0235 Lost Communication with Cruise Control Front Distance Range Sensor When the power switch is on (IG), a communication error between the millimeter wave radar sensor assembly and the driving support ECU assembly is detected for 0.652 seconds or more while the vehicle is being driven at a speed of 36 km/h (22 mph) or more.
·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

Harness or connector


U1104 Lost Communication with Driving Support ECU When the power switch is on (IG), a communication error between the driving support ECU assembly and the millimeter wave radar sensor assembly is detected for 0.192 seconds or more while the vehicle is being driven at a speed of 36 km/h (22 mph) or more.
·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

Harness or connector



WIRING DIAGRAM

A303847E42
0.104,1.677 1.031,2.052 0.927,0.375 10 false from IG1 NO. 3 Relay 1.313,1.844 2.542,2.042 1.229,0.198 10 false ECU-IG1 NO. 3 2.167,1.563 2.313,1.76 0.146,0.198 10 false 5 2.375,1.656 2.833,1.854 0.458,0.198 10 false IGB 3.094,2.104 3.708,2.302 0.615,0.198 10 false CA1P 3.083,2.771 3.698,2.969 0.615,0.198 10 false CA1N 2.385,3.344 3,3.542 0.615,0.198 10 false SGND 2.156,3.198 2.313,3.396 0.156,0.198 10 false 1 2.01,3.854 2.323,4.052 0.313,0.198 10 false A76 2,4.01 4.906,4.208 2.906,0.198 10 false Millimeter Wave Radar Sensor Assembly 3.594,1.927 3.75,2.125 0.156,0.198 10 false 3 3.594,2.573 3.75,2.771 0.156,0.198 10 false 2 2.823,0.615 4.51,0.813 1.688,0.198 10 false from IG1 NO. 3 Relay 4.417,0.802 5.49,1 1.073,0.198 10 false ECU-IG1 NO. 3 5.229,0.521 5.542,0.719 0.313,0.198 10 false 30 5.5,0.635 5.656,0.833 0.156,0.198 10 false B 5.198,1.927 5.51,2.125 0.313,0.198 10 false 40 5.219,2.615 5.531,2.813 0.313,0.198 10 false 18 5.24,3.24 5.552,3.438 0.313,0.198 10 false 25 5.49,2.115 6.104,2.313 0.615,0.198 10 false CA1P 5.479,2.75 6.094,2.948 0.615,0.198 10 false CA1N 5.49,3.344 5.948,3.542 0.458,0.198 10 false GND 5.125,3.885 5.438,4.083 0.313,0.198 10 false I176 5.135,4.042 7.052,4.552 1.917,0.51 10 false Driving Support ECU Assembly 0.885,4.375 2.688,4.563 1.802,0.188 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

When replacing the driving support ECU assembly, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle, and as a result, a DTC may be stored.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the I176 driving support ECU assembly connector.


b.

Disconnect the A76 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I176-40 (CA1P) - A76-3 (CA1P) Always Below 1 Ω
I176-18 (CA1N) - A76-2 (CA1N) Always Below 1 Ω
I176-40 (CA1P) or A76-3 (CA1P) - Body ground Always 10 kΩ or higher
I176-18 (CA1N) or A76-2 (CA1N) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (DRIVING SUPPORT ECU ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (DRIVING SUPPORT ECU ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.
C251143C69
1.5,0.344 1.896,0.573 0.396,0.229 1.667,1.271 1.333,1.729 1.333,1.729 1.115,1.729 true 1.969,1.281 2.26,1.698 2.26,1.698 2.458,1.698 true 0.979,1.656 1.583,1.885 0.604,0.229 10 false B 2.51,1.604 3.073,1.823 0.563,0.219 10 false GND 1.573,0.375 1.885,0.531 0.313,0.156 10 false I176 0.094,0.052 0.406,0.208 0.313,0.156 10 false *a
*a Rear view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the I176 driving support ECU assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I176-30 (B) - Body ground Power switch on (IG) 11 to 14 V
I176-30 (B) - Body ground Power switch off Below 1 V


Standard Resistance:
Tester Connection Condition Specified Condition
I176-25 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

3.CHECK TERMINAL VOLTAGE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.
C319199C15
1.5,0.24 1.927,0.5 0.427,0.26 2.031,1.146 2.396,0.667 2.396,0.667 2.615,0.667 true 1.354,1.146 0.938,0.656 0.938,0.656 0.75,0.656 true 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.604,0.292 2.063,0.49 0.458,0.198 10 false A76 0.333,0.583 0.792,0.781 0.458,0.198 10 false SGND 2.677,0.573 3.135,0.771 0.458,0.198 10 false IGB
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A76 millimeter wave radar sensor assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A76-5 (IGB) - Body ground Power switch on (IG) 11 to 14 V
A76-5 (IGB) - Body ground Power switch off Below 1 V


Standard Resistance:
Tester Connection Condition Specified Condition
A76-1 (SGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTCS (DTC U0235 OR U1104)
5.CHECK FOR DTCS (DTC U0235 OR U1104)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Clear DTCs
50002 197

e.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which dynamic radar cruise control system operation is possible.


ii.

Turn the cruise control system on using the cruise control main switch (ON-OFF button).


iii.

Push the cruise control main switch to -/SET to begin control of vehicle speed using the cruise control system.



f.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Trouble Codes
50001 197

Result:
Result Proceed to
DTC U0235 and U1104 are not output A
DTC U0235 or U1104 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY