Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014700 CRUISE CONTROL _0166042 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  C1A4A  Skid Control Buzzer Circuit  


DESCRIPTION

The driving support ECU assembly does this by sending a request signal to the millimeter wave radar sensor assembly to sound the skid control buzzer.

When the millimeter wave radar sensor assembly detects a malfunction in the skid control buzzer circuit, a malfunction signal is sent to the driving support ECU assembly, and this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4A Skid Control Buzzer Circuit While the power switch is on (IG), a skid control buzzer circuit malfunction signal is received from the millimeter wave radar sensor assembly for 0.272 seconds or more while the vehicle is being driven at a speed of 36 km/h (22 mph) or more.
·

Skid control buzzer

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

Harness or connector



WIRING DIAGRAM

E289273E15
5.594,3.521 6.573,3.885 0.979,0.365 10 false Driving Support ECU Assembly 3.583,3.365 3.896,3.563 0.313,0.198 10 false A76 3.573,3.521 4.969,3.875 1.396,0.354 10 false Millimeter Wave Radar Sensor Assembly 1.375,2.958 3.552,3.333 2.177,0.375 10 false Pre-crash System Warning Buzzer (Skid Control Buzzer) 1.385,2.823 1.844,3.021 0.458,0.198 10 false I171 0.646,2.427 1.635,2.615 0.99,0.188 10 false ECU-IG1 NO. 3 0.948,0.792 2.635,0.99 1.688,0.198 10 false from IG1 NO. 2 Relay 1.802,2.167 1.958,2.365 0.156,0.198 10 false 2 2.021,2.292 2.479,2.49 0.458,0.198 10 false IG1 2.49,2.292 2.802,2.49 0.313,0.198 10 false BZ 2.771,2.167 2.927,2.365 0.156,0.198 10 false 1 3.531,2.167 3.844,2.365 0.313,0.198 10 false 10 3.802,2.292 4.115,2.49 0.313,0.198 10 false BZ 0.552,4.396 2.813,4.583 2.26,0.188 10 false : CAN Communication Line 5.604,3.365 6.063,3.563 0.458,0.198 10 false I176

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the driving support ECU assembly, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle, and as a result, a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT



PROCEDURE

1.CHECK FOR DTCS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Clear DTCs
50002 197

e.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which dynamic radar cruise control system operation is possible.


ii.

Turn the cruise control system on using the cruise control main switch (ON-OFF button).


iii.

Push the cruise control main switch to -/SET to begin control of vehicle speed using the cruise control system.



f.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B
DTC C1A4A and U0235 are output C
DTC C1A4A and U1104 are output D



A

B

2.PERFORM ACTIVE TEST USING GTS (RADAR CRUISE APPROACH ALARM BUZZER)

C

D

2.PERFORM ACTIVE TEST USING GTS (RADAR CRUISE APPROACH ALARM BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Radar Cruise Approach Alarm Buzzer Skid control buzzer ON or OFF Buzzer can be heard
Body Electrical > Pre-Crash 2 > Active Test
Tester Display
Radar Cruise Approach Alarm Buzzer
50004 220 4

Result:
Result Proceed to
Skid control buzzer sounds A
Skid control buzzer does not sound B



A

REPLACE DRIVING SUPPORT ECU ASSEMBLY

B

3.INSPECT SKID CONTROL BUZZER
3.INSPECT SKID CONTROL BUZZER


Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (SKID CONTROL BUZZER - AUXILIARY BATTERY)

NG

4.CHECK TERMINAL VOLTAGE (SKID CONTROL BUZZER - AUXILIARY BATTERY)
a.
B338290C66
0.563,1.198 0.958,1.458 0.396,0.26 2.396,2 2.146,2 2.146,2 1.875,1.604 true 0.063,0.094 0.438,0.271 0.375,0.177 10 false *a 0.635,1.25 1.094,1.417 0.458,0.167 10 false I171 2.458,1.917 2.969,2.104 0.51,0.188 10 false IG1
*a Front view of wire harness connector
(to Skid Control Buzzer)


Disconnect the I171 skid control buzzer connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I171-2 (IG1) - Body ground Power switch on (IG) 11 to 14 V
I171-2 (IG1) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER - AUXILIARY BATTERY)

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the I171 skid control buzzer connector.


b.

Disconnect the A76 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I171-1 (BZ) - A76-10 (BZ) Always Below 1 Ω
I171-1 (BZ) or A76-10 (BZ) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTCS (DTC C1A4A)
7.CHECK FOR DTCS (DTC C1A4A)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Clear DTCs
50002 197

e.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which dynamic radar cruise control system operation is possible.


ii.

Turn the cruise control system on using the cruise control main switch (ON-OFF button).


iii.

Push the cruise control main switch to -/SET to begin control of vehicle speed using the cruise control system.



f.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY