Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.04
RM2040EQ _58 Vehicle Interior _035749 PRE-CRASH SAFETY _0166048 PRE-CRASH SAFETY SYSTEM U

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  TERMINALS OF ECU  


CHECK DRIVING SUPPORT ECU ASSEMBLY


E158948E50
3.458,0.208 3.823,0.448 0.365,0.24 3.521,0.25 3.917,0.5 0.396,0.25 10 false I176

a.

Disconnect the I176 driving support ECU assembly connector.

NOTICE:

If a load of more than 10 kg (22 lb.) is placed on the connector, it may break. Do not place more load than is necessary on the connector.



b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I176-5 (PBSW) - Body ground B - Body ground Pre-crash safety system switch signal Pre-crash safety system switch on Below 1 Ω
Pre-crash safety system switch off 10 kΩ or higher
I176-25 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
I176-30 (B) - Body ground V - Body ground Power source Power switch on (IG) 11 to 14 V
Power switch off Below 1 V

HINT:

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the I176 driving support ECU assembly connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I176-17 (CA2L) - I176-25 (GND) LG - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
I176-18 (CA1N) - I176-25 (GND) W - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
I176-39 (CA2H) - I176-25 (GND) L - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 3)
I176-40 (CA1P) - I176-25 (GND) LG - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 4)


e.
E228688E01
2.99,1.442 3.317,1.617 0.327,0.174 10 GND

Waveform 1

i.

CAN communication signal

Item Content
Tester Connection I176-17 (CA2L) - I176-25 (GND)
Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




f.
E228688E01
2.99,1.442 3.317,1.617 0.327,0.174 10 GND

Waveform 2

i.

CAN communication signal

Item Content
Tester Connection I176-18 (CA1N) - I176-25 (GND)
Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




g.
E228691E01
2.989,1.44 3.316,1.615 0.327,0.175 10 GND

Waveform 3

i.

CAN communication signal

Item Content
Tester Connection I176-39 (CA2H) - I176-25 (GND)
Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




h.
E228691E01
2.989,1.44 3.316,1.615 0.327,0.175 10 GND

Waveform 4

i.

CAN communication signal

Item Content
Tester Connection I176-40 (CA1P) - I176-25 (GND)
Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.