Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.04
RM2040EQ _58 Vehicle Interior _035749 PRE-CRASH SAFETY _0166048 PRE-CRASH SAFETY SYSTEM U

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Pre-Crash 2 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Wiper Information Wiper operational status Unoperat, Oil off, Mist, Washer, Unknown, Intermi, Lo or Hi The respective operational status displayed -
PCS OFF Switch Pre-crash safety system switch status ON or OFF ON: Pre-crash safety system function disabled due to switch operation
OFF: Pre-crash safety system function enabled due to switch operation
-
Pre-Crash System Pre-crash safety system control Valid or Inval Valid: Pre-crash safety system control possible
Inval: Pre-crash safety system control not possible
-
PCS Indicator "Check Pre-Crash Safety" display request signal ON or OFF ON: "Check Pre-Crash Safety" display requested
OFF: "Check Pre-Crash Safety" display not requested
-
PCS Disabled Indicator "Pre-Crash Safety Temporarily Not Available" display request signal ON or OFF ON: "Pre-Crash Safety Temporarily Not Available" display requested
OFF: "Pre-Crash Safety Temporarily Not Available" display not requested
-
Pre-Crash Safety Warning Buz Pre-crash safety system warning buzzer Valid or Inval Valid: Pre-crash safety system warning buzzer operation possible
Inval: Pre-crash safety system warning buzzer operation not possible
-
Pre-Crash Brake Pre-crash brake function Valid or Inval Valid: Pre-crash brake operation possible
Inval: Pre-crash brake operation not possible
-
Rear Collision Detection - - - Not Supported
Flushing Lamp Emergency stop light function Valid or Inval Valid: Emergency stop light operation possible
Inval: Emergency stop light operation not possible
-
PBA Start Pre-crash brake assist activation signal OFF, Standby, Assist Lv1 or Assist Lv2 OFF: Pre-crash brake assist not activated
Standby: Pre-crash brake assist standby
Assist Lv1: Pre-crash brake assist activated
Assist Lv2: Pre-crash brake assist activated
Signal status changes when the pre-crash brake assist is activated before a crash (Pre-crash brake will activate only in situations where the driver depresses the brake pedal)
Warning Brake Warning brake operation ON or OFF ON: Warning brake operating
OFF: Warning brake not operating
-
Brake Assist Standby Supplemental brake pressure signal ON or OFF ON: Supplemental brake pressure being provided
OFF: Supplemental brake pressure not being provided
Signal status changes when supplemental brake pressure is being provided after a crash is judged as unavoidable and before the brake pedal is depressed
Pre-Crash Brake Control Pre-crash brake operational status ON or OFF ON: Pre-crash brake operating
OFF: Pre-crash brake not operating
Status changes when pre-crash safety brake operates before a crash
AVS Start - - - Not Supported
VGRS Start - - - Not Supported
AHR Electricity Standby - - - Not Supported
Face Direction - - - Not Supported
Face Orientation Angle - - - Not Supported
Driver Monitor voltage - - - Not Supported
Target Horizontal Position1 - - - Not Supported
Target Horizontal Position2 - - - Not Supported
Target Distance1 - - - Not Supported
Target Distance2 - - - Not Supported
CCS Cancel Automatic cancellation of cruise control during pre-crash brake activation ON or OFF ON: Cruise control automatically canceled
OFF: Cruise control not automatically canceled
-
Pre-Crash Safety Brake Ind Pre-crash safety system "BRAKE!" alert status ON or OFF ON: Pre-crash safety system "BRAKE!" alert on
OFF: Pre-crash safety system "BRAKE!" alert off
-
PCS Crash Alarm Buzzer Skid control buzzer status ON or OFF ON: Skid control buzzer sounds
OFF: Skid control buzzer does not sound
-
ORC Backlight - - - Not Supported
Rear Radar Sensor Dirty - - - Not Supported
Rear Radar Sens Temp Hi - - - Not Supported
Rear Radar Voltage - - - Not Supported
Rear Radar Wave Transmission - - - Not Supported
Rear Radar-Dirt History - - - Not Supported
Rear Radar-Environment Hist - - - Not Supported
Front Radar-Dirt History Millimeter wave radar sensor assembly dirt history ON or OFF ON: History of excessive dirt
OFF: No history of excessive dirt
-
Front Radar-Environment Hist Millimeter wave radar sensor assembly environment condition history Good or Bad Good: No history of excessive bad environment
Bad: History of excessive bad environment
-
Recognition Camera Image History - - - Not Supported
Driver Monitor Image History - - - Not Supported
Recog ECU H Temp Stop - - - Not Supported
Recog ECU Recognize Img - - - Not Supported
Recog ECU H Temp Hist - - - Not Supported
Recognition Camera Images - - - Not Supported
Recognition Camera Voltage - - - Not Supported
Camera Height - - - Not Supported
Camera Horizontal - - - Not Supported
Target Height - - - Not Supported
Target Distance - - - Not Supported
Curr Com PCS-WIL-R - - - Not Supported
Curr Com PCS-WIL-L - - - Not Supported
Curr Com Night View ECU - - - Not Supported
Curr Com Front Camera Module - - - Not Supported
PCS Warning Sensitivity Retention Setting - - - Not Supported
PCS Operation State Retention Setting - - - Not Supported
Country# (DSS) Destination country for driving support ECU assembly JPN, NA, EURO, CA, AUS, SAFC, OTHER, TWN, CHINA, THAI, GCC or NOFIX Actual country code -
Country# (R Radar Sens) - - - Not Supported
Country# (Obj Recog ECU) - - - Not Supported
The Number of DTCs Number of DTCs min: 0, max: 255 Number of DTCs will be displayed -

f.

Enter the following menus: Powertrain / Radar Cruise / Data List.


g.

Read the Data List according to the display on the GTS.

Powertrain > Radar Cruise > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Country# (F Radar Sens) Destination country for millimeter wave radar sensor assembly JPN, NA, EURO, CA, AUS, SAFC, OTHER, TWN, CHINA, THAI, GCC or NOFIX Actual country code -

h.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


i.

Read the Data List according to the display on the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Stop Light Relay Output Stop light switch assembly (stop light relay) ON or OFF ON: Relay output on (Stop light on)
OFF: Relay output off (Stop light off)
-


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.


e.

Perform the Active Test according to the display on the GTS.

HINT:

The power switch must be turned on (IG) to proceed with the Active Test using the GTS.


Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Infrared Signal Status - - Not Supported
Face Direction Check - - Not Supported
PCS Crash Alarm Buzzer Skid control buzzer ON or OFF Buzzer can be heard
PCS Approach Alarm Buzzer Skid control buzzer ON or OFF Buzzer can be heard
LKA Lane Out Alarm Buzzer - - Not Supported

f.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


g.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Indicat. Precrash PCS warning indicator ON or OFF -

h.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


i.

Perform the Active Test according to the display on the GTS.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light switch assembly (stop light relay) ON or OFF Stop lights come on