Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.04
RM2040EQ _58 Vehicle Interior _035749 PRE-CRASH SAFETY _0166048 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A11  Front Radar Sensor Incorrect Axial Gap  C1A14  Front Radar Sensor Beam Axis Not Adjusted  


DESCRIPTION

The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle.

Based on this information, the driving support ECU assembly sends pre-crash safety control operation signals.

When the vehicle is determined to be driving in a straight line or on a gradual curve based on signals from the airbag sensor assembly (yaw rate sensor) etc., the millimeter wave radar sensor assembly performs self-diagnosis to check if the sensor beam axis has deviated from the vehicle movement direction. When the millimeter wave radar sensor assembly beam axis has deviated, the driving support ECU assembly detects this, and stores DTC C1A11.

After installing a new millimeter wave radar sensor assembly, if sensor beam axis adjustment is not performed, DTC C1A14 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A11 Front Radar Sensor Incorrect Axial Gap When the power switch is on (IG), misalignment of the millimeter wave radar sensor assembly is detected for 1.272 seconds.
·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly


C1A14 Front Radar Sensor Beam Axis Not Adjusted When the vehicle is being driven at a speed of 10 km/h (6 mph) or more, misalignment of the millimeter wave radar sensor assembly is detected for 0.272 second.
·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Check that the bracket of the millimeter wave radar sensor assembly is not deformed.

HINT:

If the bracket is deformed, replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL



b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTCS (PRE-CRASH 2)
2.CHECK FOR DTCS (PRE-CRASH 2)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

e.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



f.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
Result:
Result Proceed to
DTC C1A11 and C1A14 are not output A
DTC C1A11 or C1A14 is output B




A

END

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY