Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.04
RM2040EQ _58 Vehicle Interior _035749 PRE-CRASH SAFETY _0166048 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A4A  Skid Control Buzzer Circuit  


DESCRIPTION

Based on pre-crash safety control, the driving support ECU assembly provides warnings to the driver. The driving support ECU assembly does this by sending a request signal to the millimeter wave radar sensor assembly to sound the skid control buzzer.

When the millimeter wave radar sensor assembly detects a malfunction in the skid control buzzer circuit, a malfunction signal is sent to the driving support ECU assembly, and this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4A Skid Control Buzzer Circuit While the power switch is on (IG), a skid control buzzer circuit malfunction signal is received from the millimeter wave radar sensor assembly for 3 seconds or more.
·

Harness or connector

·

Skid control buzzer

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly



WIRING DIAGRAM

B338289E22
3.667,2.719 4.219,2.885 0.552,0.167 10 false A76 5.802,2.719 7.073,3.083 1.271,0.365 10 false Driving Support ECU Assembly 3.667,2.875 5.063,3.229 1.396,0.354 10 false Millimeter Wave Radar Sensor Assembly 2.25,1.583 2.469,1.813 0.219,0.229 10 false 2 3.74,1.688 4.188,1.99 0.448,0.302 10 false BZ 3.469,1.594 3.719,1.823 0.25,0.229 10 false 10 1.052,3.281 3.042,3.521 1.99,0.24 10 false : CAN Communication Line 0.094,1.667 1.031,2.01 0.938,0.344 10 false from IG1 NO. 3 Relay 1.5,1.823 2.073,2.167 0.573,0.344 10 false ECU-IG1 NO. 3 3.188,1.583 3.271,1.958 0.083,0.375 10 false 1 2.917,1.656 3.281,1.896 0.365,0.24 10 false BZ 2.406,1.667 2.688,1.896 0.281,0.229 10 false IG1 2.167,2.073 3.896,2.219 1.729,0.146 10 false I171 2.167,2.229 3.458,2.469 1.292,0.24 10 false Skid Control Buzzer

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.CHECK FOR DTCS (PRE-CRASH 2)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

e.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



f.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
Result:
Result Proceed to
DTC C1A4A, U1002, U0235 and U1104 are not output A
DTC C1A4A is output B
DTC C1A4A and U0235 are output C
DTC C1A4A and U1002 are output D
DTC C1A4A and U1104 are output E




A

B

2.PERFORM ACTIVE TEST USING GTS (SKID CONTROL BUZZER)

C

D

E

2.PERFORM ACTIVE TEST USING GTS (SKID CONTROL BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer ON or OFF Buzzer can be heard
PCS Approach Alarm Buzzer Skid control buzzer ON or OFF Buzzer can be heard
Body Electrical > Pre-Crash 2 > Active Test
Tester Display
PCS Crash Alarm Buzzer
50004 220 5
Body Electrical > Pre-Crash 2 > Active Test
Tester Display
PCS Approach Alarm Buzzer
50004 220 6
OK:

Skid control buzzer sounds.



Result:
Proceed to
OK
NG



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

3.INSPECT SKID CONTROL BUZZER
3.INSPECT SKID CONTROL BUZZER


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - BATTERY)

NG

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - BATTERY)
a.
B338290C65
0.542,1.198 0.938,1.458 0.396,0.26 2.396,2 2.146,2 2.146,2 1.875,1.604 true 0.063,0.094 0.323,0.229 0.26,0.135 10 false *a 0.615,1.25 0.969,1.458 0.354,0.208 10 false I171 2.448,1.917 2.896,2.135 0.448,0.219 10 false IG1
*a Front view of wire harness connector
(to Skid Control Buzzer)


Disconnect the I171 skid control buzzer connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I171-2 (IG1) - Body ground Power switch on (IG) 11 to 14 V
I171-2 (IG1) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the I171 skid control buzzer connector.


b.

Disconnect the A76 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I171-1 (BZ) - A76-10 (BZ) Always Below 1 Ω
I171-1 (BZ) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTCS (PRE-CRASH 2)
7.CHECK FOR DTCS (PRE-CRASH 2)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

e.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



f.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B




A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY