Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.04
RM2040EQ _58 Vehicle Interior _035749 PRE-CRASH SAFETY _0166048 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  U0125  Lost Communication with Yaw Rate Sensor Module  U0126  Lost Communication with Steering Angle Sensor Module  U0129  Lost Communication with Brake System Control Module  U0142  Lost Communication with Body Control Module "B"  U0293  Lost Communication with Hybrid Vehicle Control System  U1104  Lost Communication with Driving Support ECU  


DESCRIPTION

The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle. Based on this information, the driving support ECU assembly sends pre-crash safety control operation signals. These DTCs are stored when a communication malfunction occurs between the sensors and ECUs that detect crashes, or between ECUs that perform the pre-crash safety control.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0125 Lost Communication with Yaw Rate Sensor Module When the power switch is on (IG), a communication error between the airbag sensor assembly (yaw rate sensor) and the driving support ECU assembly is detected for 3.772 seconds.
·

CAN communication system

·

Airbag sensor assembly (Yaw rate sensor)

·

Driving support ECU assembly


U0126 Lost Communication with Steering Angle Sensor Module When the power switch is on (IG), a communication error between the steering angle sensor and the driving support ECU assembly is detected for 4.76 seconds.
·

CAN communication system

·

Steering angle sensor

·

Driving support ECU assembly


U0129 Lost Communication with Brake System Control Module When the power switch is on (IG), a communication error between the skid control ECU (brake booster with master cylinder assembly) and the driving support ECU assembly is detected for 7.24 seconds.
·

CAN communication system

·

Skid control ECU (Brake booster with master cylinder assembly)

·

Driving support ECU assembly


U0142 Lost Communication with Body Control Module "B" When the power switch is on (IG), a communication error between the main body ECU (multiplex network body ECU) and driving support ECU assembly is detected for 15.2 seconds.
·

CAN communication system

·

Main body ECU (Multiplex network body ECU)

·

Driving support ECU assembly


U0293 Lost Communication with Hybrid Vehicle Control System When the power switch is on (IG), a communication error between the power management control ECU and driving support ECU assembly is detected for 3.808 seconds or more while the vehicle is being driven at a speed of 5 km/h (3 mph) or more.
·

CAN communication system

·

Power management control ECU

·

Driving support ECU assembly


U1104 Lost Communication with Driving Support ECU When the power switch is on (IG), a communication error between power management control ECU and driving support ECU assembly or skid control ECU (brake booster with master cylinder assembly) is detected for 3.504 seconds or more.
·

CAN communication system

·

Power management control ECU

·

Driving support ECU assembly

·

Skid control ECU (Brake booster with master cylinder assembly)



PROCEDURE

1.CHECK FOR DTCS (PRE-CRASH 2)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

e.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



f.

Check the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B




A

B