Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.04
RM2040EQ _58 Vehicle Interior _035749 PRE-CRASH SAFETY _0166048 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  U1002  Lost Communication with Gateway Module  U1104  Lost Communication with Driving Support ECU  


DESCRIPTION

The driving support ECU assembly sends vehicle speed and vehicle condition information to the millimeter wave radar sensor assembly. The millimeter wave radar sensor assembly then sends information on the presence, distance, and relative speed of objects ahead to the driving support ECU assembly. The driving support ECU assembly sends this information to the hybrid vehicle control ECU and performs pre-crash safety system operation.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0235 Lost Communication with Cruise Control Front Distance Range Sensor When the power switch is on (IG), a communication error between the millimeter wave radar sensor assembly and the driving support ECU assembly is detected for 1.652 seconds.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly


U1002 Lost Communication with Gateway Module When the power switch is on (IG), a communication error between the millimeter wave radar sensor assembly and the driving support ECU assembly is detected for 1.652 seconds.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly


U1104 Lost Communication with Driving Support ECU When the power switch is on (IG), a communication error between the millimeter wave radar sensor assembly and the driving support ECU assembly is detected for 1.192 seconds.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly



WIRING DIAGRAM

A303847E40
0.104,1.677 1.031,2.052 0.927,0.375 10 false from IG1 NO. 3 Relay 1.313,1.844 2.542,2.042 1.229,0.198 10 false ECU-IG1 NO. 3 2.167,1.563 2.313,1.76 0.146,0.198 10 false 5 2.375,1.656 2.833,1.854 0.458,0.198 10 false IGB 3.094,2.104 3.708,2.302 0.615,0.198 10 false CA1P 3.083,2.771 3.698,2.969 0.615,0.198 10 false CA1N 2.385,3.344 3,3.542 0.615,0.198 10 false SGND 2.156,3.198 2.313,3.396 0.156,0.198 10 false 1 2.01,3.854 2.323,4.052 0.313,0.198 10 false A76 2,4.01 4.906,4.208 2.906,0.198 10 false Millimeter Wave Radar Sensor Assembly 3.594,1.927 3.75,2.125 0.156,0.198 10 false 3 3.594,2.573 3.75,2.771 0.156,0.198 10 false 2 2.823,0.615 4.51,0.813 1.688,0.198 10 false from IG1 NO. 3 Relay 4.417,0.802 5.49,1 1.073,0.198 10 false ECU-IG1 NO. 3 5.229,0.521 5.542,0.719 0.313,0.198 10 false 30 5.5,0.635 5.656,0.833 0.156,0.198 10 false B 5.198,1.927 5.51,2.125 0.313,0.198 10 false 40 5.219,2.615 5.531,2.813 0.313,0.198 10 false 18 5.24,3.24 5.552,3.438 0.313,0.198 10 false 25 5.49,2.115 6.104,2.313 0.615,0.198 10 false CA1P 5.479,2.75 6.094,2.948 0.615,0.198 10 false CA1N 5.49,3.344 5.948,3.542 0.458,0.198 10 false GND 5.125,3.885 5.438,4.083 0.313,0.198 10 false I176 5.135,4.042 7.052,4.552 1.917,0.51 10 false Driving Support ECU Assembly 0.885,4.375 2.688,4.563 1.802,0.188 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the I176 driving support ECU assembly connector.


b.

Disconnect the A76 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I176-40 (CA1P) - A76-3 (CA1P) Always Below 1 Ω
I176-18 (CA1N) - A76-2 (CA1N) Always Below 1 Ω
I176-40 (CA1P) - Body ground Always 10 kΩ or higher
I176-18 (CA1N) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
C251143C70
1.5,0.344 1.896,0.573 0.396,0.229 1.667,1.271 1.333,1.729 1.333,1.729 1.115,1.729 true 1.969,1.281 2.26,1.698 2.26,1.698 2.458,1.698 true 0.979,1.656 1.583,1.885 0.604,0.229 10 false B 2.51,1.604 3.073,1.823 0.563,0.219 10 false GND 1.583,0.385 1.896,0.542 0.313,0.156 10 false I176 0.094,0.052 0.406,0.208 0.313,0.156 10 false *a
*a Rear view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the I176 driving support ECU assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I176-30 (B) - Body ground Power switch on (IG) 11 to 14 V
I176-30 (B) - Body ground Power switch off Below 1 V


Standard Resistance:
Tester Connection Condition Specified Condition
I176-25 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
C319199C17
1.5,0.24 1.927,0.5 0.427,0.26 2.031,1.146 2.396,0.667 2.396,0.667 2.615,0.667 true 1.354,1.146 0.938,0.656 0.938,0.656 0.75,0.656 true 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.604,0.292 2.063,0.49 0.458,0.198 10 false A76 0.333,0.583 0.792,0.781 0.458,0.198 10 false SGND 2.677,0.573 3.135,0.771 0.458,0.198 10 false IGB
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A76 millimeter wave radar sensor assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A76-5 (IGB) - Body ground Power switch on (IG) 11 to 14 V
A76-5 (IGB) - Body ground Power switch off Below 1 V


Standard Resistance:
Tester Connection Condition Specified Condition
A76-1 (SGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTCS (PRE-CRASH 2)
5.CHECK FOR DTCS (PRE-CRASH 2)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

e.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



f.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
Result:
Result Proceed to
DTC U0235, U1002 and U1104 are not output A
DTC U0235, U1002 or U1104 is output B




A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY