Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014700 CRUISE CONTROL _0074941 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Main Indicator Light Circuit  


DESCRIPTION

·

The power management control ECU turns on the cruise control indicator light by sending indicator output demand signals to the combination meter assembly using CAN communication.

·

The cruise control indicator light illuminates when the cruise control system has been turned on using the ON-OFF switch. If a malfunction is detected, the cruise control indicator light goes out and a warning message is displayed.

·

The cruise control indicator light circuit uses CAN communication. If the cruise control indicator light is not functioning correctly, check for CAN communication DTCs before troubleshooting this circuit.


WIRING DIAGRAM

E230248E49
0.823,2.26 2.969,2.448 2.146,0.188 10 false : CAN Communication Line 4.667,0.49 4.865,0.646 0.198,0.156 10 false 25 4.927,0.708 5.375,0.885 0.448,0.177 10 false CA1H 4.667,1 4.865,1.156 0.198,0.156 10 false 24 4.833,1.729 5.094,1.885 0.26,0.156 10 false I4 4.833,1.917 7.104,2.125 2.271,0.208 10 false Power Management Control ECU 0.917,1.708 1.135,1.865 0.219,0.156 10 false I18 0.917,1.875 2.854,2.094 1.938,0.219 10 false Combination Meter Assembly 4.927,1.208 5.406,1.406 0.479,0.198 10 false CA1L 2.594,0.49 2.792,0.646 0.198,0.156 10 false 17 2.104,0.667 2.521,0.823 0.417,0.156 10 false CANH 2.594,1 2.792,1.156 0.198,0.156 10 false 16 2.104,1.167 2.521,1.323 0.417,0.156 10 false CANL

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (METER DISPLAY 1)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Meter Display 1 Multi-information display OFF or All -
Body Electrical > Combination Meter > Active Test
Tester Display
Meter Display 1
50004 122 7

Result:
Result Proceed to
The multi-information display in the combination meter assembly turns on or off according to the operation of the Active Test. A
The multi-information display in the combination meter assembly does not turn on or off according to the operation of the Active Test. B



A

2.READ VALUE USING GTS (CCS INDICATOR M-CPU)

B

2.READ VALUE USING GTS (CCS INDICATOR M-CPU)
a.

Enter the following menus: Powertrain / Cruise Control / Data List.


b.

Read the Data List according to the display on the GTS.

Powertrain > Cruise Control
Tester Display Measurement Item Range Normal Condition Diagnostic Note
CCS Indicator M-CPU Cruise control indicator (Main-CPU) ON or OFF ON: Cruise control indicator light illuminated
OFF: Cruise control indicator light not on
-
Powertrain > Cruise Control > Data List
Tester Display
CCS Indicator M-CPU
50003 238 12

Result:
Result Proceed to
The cruise control indicator illuminates and turns off according to the operation of the cruise control main switch (ON-OFF switch). A
The cruise control indicator does not illuminate but the Data List item CCS Indicator M-CPU changes according to the operation of the cruise control main switch (ON-OFF switch). B
The cruise control indicator does not illuminate and the Data List item CCS Indicator M-CPU does not change according to the operation of the cruise control main switch (ON-OFF switch). C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE COMBINATION METER ASSEMBLY

C