Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014700 CRUISE CONTROL _0074941 CRUISE CONTROL SYSTEM U

CRUISE CONTROL  CRUISE CONTROL SYSTEM  TERMINALS OF ECU  


CHECK POWER MANAGEMENT CONTROL ECU


E186873E16
1.18,0.501 1.577,0.739 0.397,0.238 1.254,0.547 1.539,0.729 0.285,0.182 10 A38 2.639,0.501 3.036,0.739 0.397,0.238 2.713,0.547 3.061,0.729 0.348,0.182 10 A39 4.282,0.501 4.679,0.739 0.397,0.238 4.409,0.547 4.632,0.729 0.223,0.182 10 I3 5.644,0.501 6.041,0.739 0.397,0.238 5.772,0.547 5.967,0.729 0.195,0.182 10 I4

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A38-6 (ST1-) - I3-6 (E1) GR - BR Stop light switch signal Power switch on (IG), Brake pedal released 11 to 14 V
A38-6 (ST1-) - I3-6 (E1) GR - BR Stop light switch signal Power switch on (IG), Brake pedal depressed Below 1 V
I4-10 (STP) - I3-6 (E1) W - BR Stop light switch signal Brake pedal released Below 1 V
I4-10 (STP) - I3-6 (E1) W - BR Stop light switch signal Brake pedal depressed 11 to 14 V
I3-6 (E1) - Body ground BR - Body ground Earth (ground) circuit of power management control ECU Always Below 1 Ω
I4-8 (TC) - I3-6 (E1) R - BR Terminal TC of DLC3 Power switch on (IG) 11 to 14 V
I4-8 (TC) - I3-6 (E1) R - BR Terminal TC of DLC3 Terminals TC and CG of DLC3 connected Below 1 V
I3-16 (SPDI) - I3-6 (E1) V - BR Vehicle speed signal Driving at 20 km/h (12 mph) Pulse generation
(see waveform 1)
I4-23 (CCS) - I3-6 (E1) W - BR Cruise control switch circuit Power switch on (IG) 11 to 14 V
I4-23 (CCS) - I3-6 (E1) W - BR Cruise control switch circuit Power switch on (IG), Cruise control switch on Below 1 V
I4-23 (CCS) - I3-6 (E1) W - BR Cruise control switch circuit Power switch on (IG), +/RES switch on 2.3 to 4.0 V
I4-23 (CCS) - I3-6 (E1) W - BR Cruise control switch circuit Power switch on (IG), -/SET switch on 4.5 to 7.1 V
I4-23 (CCS) - I3-6 (E1) W - BR Cruise control switch circuit Power switch on (IG), CANCEL switch on 6.6 to 10.1 V
I4-24 (CA1L) - I3-6 (E1) W - BR CAN communication line Power switch on (IG) Pulse generation
(see waveform 2)
I4-25 (CA1H) - I3-6 (E1) BE - BR CAN communication line Power switch on (IG) Pulse generation
(see waveform 3)

a.
A306367E01
2.969,1.198 3.427,1.396 0.458,0.198 10 false GND

WAVEFORM 1

i.

Vehicle speed signal

Power Management Control ECU Terminal Name Between I3-16 (SPDI) and I3-6 (E1)
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:
·

The wavelength becomes shorter as the vehicle speed increases.

·

Depending on the vehicle, the output waveform voltage may rise to 12 V if influenced by optionally installed systems.





b.
A194184E12
2.99,2.042 3.333,2.208 0.344,0.167 10 false GND 2.75,0.594 3.281,0.771 0.531,0.177 10 false 1 V/DIV. 1.115,2.542 1.969,2.719 0.854,0.177 10 false 10 μsec./DIV.

WAVEFORM 2

i.

CAN communication signal

Power Management Control ECU Terminal Name Between I4-24 (CA1L) and I3-6 (E1)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




c.
A194183E11
2.958,2.052 3.302,2.219 0.344,0.167 10 false GND 2.76,0.604 3.292,0.781 0.531,0.177 10 false 1 V/DIV. 1.115,2.542 1.99,2.719 0.875,0.177 10 false 10 μsec./DIV.

WAVEFORM 3

i.

CAN communication signal

Power Management Control ECU Terminal Name Between I4-25 (CA1H) and I3-6 (E1)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.