Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER › from 2015.04
RM2040EQ _53 Suspension _014705 FRONT SUSPENSION _0074966 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 48158C 1.INSTALL FRONT LOWER COIL SPRING INSULATOR

a.
C310546C06
1.896,1.031 2.51,0.365 2.51,0.365 2.656,0.365 true 2.719,0.281 3.031,0.479 0.313,0.198 10 false *a
*a Claw
V100135

Positioning Pin


Install the front lower coil spring insulator to the front shock absorber assembly.

NOTICE:
·

Make sure that the positioning pins on the front lower coil spring insulator are inserted into the holes in the front shock absorber assembly.

·

When installing the front lower coil spring insulator, make sure that the front lower coil spring insulator does not get caught on the claws of the front shock absorber assembly.




Hide 48331C 2.INSTALL FRONT SPRING BUMPER

a.
C310547

Install the front spring bumper to the front shock absorber assembly.

NOTICE:

Face the smaller diameter end of the front spring bumper downward.



Hide 48132 3.INSTALL FRONT COIL SPRING

a.
C265549N04
2.524,1.627 2.524,1.295 2.524,1.295 2.692,1.295 false 2.713,1.204 3.024,1.360 0.311,0.156 10 SST

Secure SST in a vise.

SST
09727-30021  (09727-00010, 09727-00021, 09727-00031)


b.
C275706C01
0.323,0.167 0.719,0.563 0.396,0.396 10 false *a 0.354,2.479 0.677,2.781 0.323,0.302 10 false *b
*a Correct
*b Incorrect


Attach the arms of SST to the diameter of the front coil spring.

CAUTION:
·

Make sure that the front coil spring is installed so that the distance between the upper and lower arms of SST is at the maximum.

·

Make sure that the claws of the arms are securely attached.




c.

Using SST, compress the front coil spring.

CAUTION:
·

If the front coil spring bends during compression, immediately stop compression and reinstall SST.

·

Do not excessively compress the front coil spring so that the coils contact each other.

·

Do not use an impact wrench. It will damage SST.




d.
C267416N04
0.417,1.833 0.417,1.656 false 0.292,1.844 0.75,2.042 0.458,0.198 10 SST

Install the front coil spring to the front shock absorber assembly.

NOTICE:

Make sure that the end of the front coil spring is positioned in the depression of the front lower coil spring insulator.



Hide 48157C 4.INSTALL FRONT UPPER COIL SPRING INSULATOR

a.
C314719C09
1.708,0.865 2.021,1.063 0.313,0.198 10 false 5° 1.698,0.313 2.01,0.51 0.313,0.198 10 false 5°
V100136

Outside of the Vehicle


Install the front upper coil spring insulator as shown in the illustration.

NOTICE:

Any misalignment between the front shock absorber lower bracket and the alignment mark must be +/- 5°.


HINT:

The lower end of the front upper coil spring insulator will engage with the claws of the front shock absorber assembly when the suspension is stabilized.



Hide 48471C 5.INSTALL FRONT UPPER COIL SPRING SEAT

a.
C315323C08
1.74,0.385 2.052,0.583 0.313,0.198 10 false 5° 1.74,0.844 2.052,1.042 0.313,0.198 10 false 5°
V100136

Outside of the Vehicle


Install the front upper coil spring seat with the mark facing the outside of the vehicle.

NOTICE:

Any misalignment between the front shock absorber lower bracket and the alignment mark must be +/- 5°.



Hide 48609C 6.INSTALL FRONT SUSPENSION SUPPORT BEARING

a.
C263336C02
0.641,0.184 0.803,0.341 0.162,0.157 10 *a
*a Upper Side


Install the front suspension support bearing as shown in the illustration.

NOTICE:

Do not install the bearing upside down.



Hide 48609 7.INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

a.
C317490C06
0,0 0,0 false
V100135

Outside of the Vehicle


Install the front suspension support sub-assembly as shown in the illustration.

NOTICE:

Check that the slot on the piston rod and the slot on the front suspension support sub-assembly are aligned.



b.

Temporarily tighten a new front support to front shock absorber nut.


c.
C132423C05
2.042,1.646 2.917,1.99 0.875,0.344 10 false 10° +/- 5°
V100136

Outside of the Vehicle


While aligning the stud bolt of the front suspension support sub-assembly and the front shock absorber lower bracket, remove SST from the front coil spring.

NOTICE:
·

When reassembling the front suspension support sub-assembly, ensure that any misalignment between the absorber lower bracket and the stud bolt is within +/- 5°. Use the stud bolt that is closest to the outside of the vehicle.

·

Do not use an impact wrench. It will damage SST.




Hide 8.INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING

a.

Install the front shock absorber with coil spring (upper side) with the 3 nuts.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)


b.

Install the front shock absorber with coil spring (lower side) to the steering knuckle and insert the 2 bolts and 2 nuts.

Torque:
290 N*m (2957 kgf*cm, 214 ft.*lbf)

NOTICE:

While keeping the bolts from rotating, tighten the nuts.



Hide 48810 9.INSTALL FRONT STABILIZER LINK ASSEMBLY

a.

Install the front stabilizer link assembly to the front shock absorber assembly with the nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a hexagon wrench to hold the stud bolt.



Hide 89543 10.INSTALL FRONT SPEED SENSOR

a.

Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt and clamp.

Torque:
19 N*m (192 kgf*cm, 14 ft.*lbf)

NOTICE:

Do not twist the front speed sensor when installing it.


HINT:

Install the speed sensor harness bracket first and then the front flexible hose.



Hide 11.FULLY TIGHTEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.

Fully tighten the front support to front shock absorber nut.

Torque:
70 N*m (714 kgf*cm, 52 ft.*lbf)

NOTICE:

Perform this step only when the front shock absorber with coil spring has been disassembled.



Hide 12.INSTALL FRONT WHEEL

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)

Hide 13.STABILIZE SUSPENSION

a.

Lower the vehicle and bounce it up and down several times to stabilize the front suspension.


Hide 14.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT