Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.04
RM2040EQ _58 Vehicle Interior _014727 SUPPLEMENTAL RESTRAINT SYSTEMS _0075078 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are displayed by blinking of the SRS warning light.

HINT:
·

When multiple warning lights in the combination meter blink continuously, a short to ground in the wiring or an ECU connected to terminal TC of the DLC3 is suspected.

·

A DTC output mode signal is transmitted via CAN communication to each ECU including the airbag sensor assembly. Thus when multiple systems do not enter DTC output mode, there may be a malfunction in the power management control ECU.



WIRING DIAGRAM

C248718E38
0.521,4.083 2.615,4.323 2.094,0.24 10 false Power Management Control ECU 0.531,3.917 2.667,4.188 2.135,0.271 10 false I4 1.375,1.24 1.667,1.677 0.292,0.438 10 false 24 1.375,0.542 1.656,0.823 0.281,0.281 10 false 25 1.375,2.667 1.917,3.073 0.542,0.406 10 false 8 0.948,1.396 1.469,1.865 0.521,0.469 10 false CA1L 0.927,0.688 1.469,1.115 0.542,0.427 10 false CA1H 5.958,2.75 6.292,3.021 0.333,0.271 10 false TC 1.115,2.76 1.521,3.042 0.406,0.281 10 false TC 5.719,2.656 6.052,2.969 0.333,0.313 10 false 13 5.802,3.281 6.104,3.531 0.302,0.25 10 false 4 5.958,3.375 6.302,3.667 0.344,0.292 10 false CG 6.167,3.917 6.646,4.333 0.479,0.417 10 false I39 6.167,4.083 6.75,4.5 0.583,0.417 10 false DLC3 5.958,1.385 6.427,1.646 0.469,0.26 10 false CANL 5.604,1.844 6.01,2.104 0.406,0.26 10 false I47 5.719,1.25 6.01,1.521 0.292,0.271 10 false 22 5.719,0.542 6.052,0.792 0.333,0.25 10 false 13 5.958,0.677 6.479,1.094 0.521,0.417 10 false CANH 5.604,2 7.156,2.396 1.552,0.396 10 false Airbag Sensor Assembly 0.75,4.438 2.573,4.708 1.823,0.271 10 false : CAN Communication Line

PROCEDURE

1.CHECK WIRE HARNESS (TC OF DLC3 - TC OF POWER MANAGEMENT CONTROL ECU)
a.
C286199C05
0.208,1.01 0.563,1.25 0.354,0.24 0.26,3.417 0.615,3.646 0.354,0.229 2.073,1.906 2.073,1.49 false 0.719,3.938 1.125,3.5 false 0.198,0.156 0.542,0.448 0.344,0.292 10 false *1 0.281,2.417 0.646,2.781 0.365,0.365 10 false *a 0.302,1.052 0.646,1.344 0.344,0.292 10 false I39 0.396,3.448 0.74,3.74 0.344,0.292 10 false I4 2,1.927 2.344,2.219 0.344,0.292 10 false TC 0.615,3.958 0.958,4.25 0.344,0.292 10 false TC
*1 DLC3
*a Front view of wire harness connector
(to Power Management Control ECU)


Turn the power switch off.


b.

Disconnect the connector from the power management control ECU.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-13 (TC) - I4-8 (TC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE WIRE HARNESS

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)
a.
C204945C03
0.094,0.615 0.427,0.833 0.333,0.219 1.615,0.802 1.615,0.302 1.615,0.302 1.813,0.302 false 0.156,0.135 0.469,0.396 0.313,0.26 10 *1 0.177,0.646 0.49,0.948 0.313,0.302 10 I39 1.854,0.219 2.25,0.469 0.396,0.25 10 CG
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE WIRE HARNESS

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)
a.
C204945C04
0.156,0.594 0.49,0.823 0.333,0.229 1.958,1.76 1.792,1.76 1.792,1.76 1.792,1.344 false 0.125,0.115 0.406,0.396 0.281,0.281 10 *1 0.24,0.625 0.802,1.083 0.563,0.458 10 I39 2.021,1.688 2.354,1.979 0.333,0.292 10 TC
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-13 (TC) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE WIRE HARNESS OR REPLACE EACH ECU