After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Turn the power switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.
Turn the power switch off before inspecting CAN bus lines for a ground short.
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
This section describes the standard values for all CAN related components.
Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
CAN JUNCTION LH1 CONNECTOR
Check the CAN junction LH1 connector.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.
Connection diagram
| *a | Component with harness connected
(CAN Junction LH1 Connector) |
*b | to Power Management Control ECU
(for V Bus) |
| *c | to Main Body ECU (Multiplex Network Body ECU)
(for V Bus) |
*d | to Air Conditioning Amplifier Assembly
(for V Bus) |
| *e | to Airbag Sensor Assembly
(for V Bus) |
*f | to Power Steering ECU Assembly
(for V Bus) |
| *g | to ECM
(for V Bus) |
*h | Navigation ECU Sub-assembly
(for Navigation Receiver Type with HDD) (for V Bus) |
| *i | Radio and Display Receiver Assembly
(for Radio and Display Type) |
*j | Navigation Receiver Assembly
(for Navigation Receiver Type without HDD) (for V Bus) |
| *k | to CAN Junction RH1 Connector
(for V Bus) |
- | - |
Check the connection diagram of the components which are connected to the CAN junction LH1 connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| I109-1 (CANH) | BE | Power management control ECU
(for V bus) |
| I109-2 (CANL) | W | |
| I95-1 (CANH) | P | Main body ECU (Multiplex network body ECU)
(for V bus) |
| I95-2 (CANL) | W | |
| I102-1 (CANH) | V | Air conditioning amplifier assembly
(for V bus) |
| I102-2 (CANL) | W | |
| I103-1 (CANH) | Y | Airbag sensor assembly
(for V bus) |
| I103-2 (CANL) | W | |
| I100-1 (CANH) | L | Power steering ECU assembly
(for V bus) |
| I100-2 (CANL) | W | |
| I104-1 (CANH) | G | ECM
(for V bus) |
| I104-2 (CANL) | W | |
| I107-1 (CANH) | R | Navigation ECU sub-assembly*1
(for V bus) |
| I107-2 (CANL) | W | |
| I107-1 (CANH) | R | Radio and display receiver assembly*2
(for V bus) |
| I107-2 (CANL) | W | |
| I107-1 (CANH) | R | Navigation receiver assembly*3
(for V bus) |
| I107-2 (CANL) | W | |
| I93-1 (CANH) | B | CAN junction RH1 connector
(for V bus) |
| I93-2 (CANL) | W |
*1: for Navigation Receiver Type with HDD
*2: for Radio and Display Type
*3: for Navigation Receiver Type without HDD
CAN JUNCTION RH1 CONNECTOR
Check the CAN junction RH1 connector.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.
Connection diagram
| *a | Component with harness connected
(CAN Junction RH1 Connector) |
*b | to Headlight Swivel ECU Assembly (AFS ECU)
(w/ Automatic High Beam System) (for V Bus) |
| *c | to Steering Sensor
(for V Bus) |
*d | to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for V Bus) |
| *e | to Smart Key ECU Assembly (Certification ECU)
(for V Bus) |
*f | to DLC3
(for V Bus) |
| *g | to Combination Meter Assembly
(for V Bus) |
*h | to CAN Junction LH1 Connector
(for V Bus) |
Check the connection diagram of the components which are connected to the CAN junction RH1 connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| I112-1 (CANH) | BE | Headlight swivel ECU assembly (AFS ECU)*
(for V bus) |
| I112-2 (CANL) | W | |
| I97-1 (CANH) | V | Steering sensor
(for V bus) |
| I97-2 (CANL) | W | |
| I110-1 (CANH) | Y | Brake booster with master cylinder assembly (Skid control ECU)
(for V bus) |
| I110-2 (CANL) | W | |
| I106-1 (CANH) | L | Smart key ECU assembly (Certification ECU)
(for V bus) |
| I106-2 (CANL) | W | |
| I96-1 (CANH) | G | DLC3
(for V bus) |
| I96-2 (CANL) | W | |
| I94-1 (CANH) | R | Combination meter assembly
(for V bus) |
| I94-2 (CANL) | W | |
| I101-1 (CANH) | B | CAN junction LH1 connector
(for V bus) |
| I101-2 (CANL) | W |
*: w/ Automatic High Beam System
CAN JUNCTION LH2 CONNECTOR (w/ Seat Position Memory System)
Check the CAN junction LH2 connector.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.
Connection diagram
| *1 | CAN Junction LH2 Connector | - | - |
| *a | Junction Connector A Side | *b | Junction Connector B Side |
| *c | Earth Terminal | *d | Front view of wire harness connector
(to CAN Junction LH2 Connector) |
Check the connection diagram of the components which are connected to the CAN junction LH2 connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| I162-1 (CANH) | R | Main body ECU (Multiplex network body ECU)
(for Sub bus 1) |
| I162-2 (CANL) | GR | |
| I163-1 (CANH) | G | Outer mirror control ECU assembly (for Front passenger side)
(for Sub bus 1) |
| I163-2 (CANL) | GR | |
| I166-1 (CANH) | Y | CAN junction RH2 connector
(for Sub bus 1) |
| I166-2 (CANL) | GR |
CAN JUNCTION RH2 CONNECTOR (w/ Seat Position Memory System)
Check the CAN junction RH2 connector.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.
Connection diagram
| *1 | CAN Junction RH2 Connector | - | - |
| *a | Junction Connector A Side | *b | Junction Connector B Side |
| *c | Earth Terminal | *d | Front view of wire harness connector
(to CAN Junction RH2 Connector) |
Check the connection diagram of the components which are connected to the CAN junction RH2 connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| I168-1 (GND) | W-B | Body ground |
| I167-1 (CANH) | Y | CAN junction LH2 connector
(for Sub bus 1) |
| I167-2 (CANL) | GR | |
| I165-1 (CANH) | BE | Position control ECU and switch assembly (for Driver side)
(for Sub bus 1) |
| I165-2 (CANL) | GR | |
| I164-1 (CANH) | P | Outer mirror control ECU assembly (for Driver side)
(for Sub bus 1) |
| I164-2 (CANL) | GR |
CAN NO. 1 JUNCTION CONNECTOR
Check the CAN No. 1 junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to CAN No. 1 Junction Connector) |
*b | to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for Sub Bus 15) |
| *c | to ECM
(for Sub Bus 15) |
*d | to Power Management Control ECU
(for Sub Bus 15) |
Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| A72-1 (CANH) | B | Brake booster with master cylinder assembly (Skid control ECU)
(for Sub bus 15) |
| A72-7 (CANL) | W | |
| A72-2 (CANH) | B | ECM
(for Sub bus 15) |
| A72-8 (CANL) | W | |
| A72-3 (CANH) | B | Power management control ECU
(for Sub bus 15) |
| A72-9 (CANL) | W |
CAN NO. 2 JUNCTION CONNECTOR
Check the CAN No. 2 junction connector.
| *a | Front view of wire harness connector
(to CAN No. 2 Junction Connector) |
| *b | to Blind Spot Monitor Sensor RH
(w/ Blind Spot Monitor System) (for Sub Bus 11) |
| *c | to CAN No. 3 Junction Connector
(for Sub Bus 11) |
| *d | to Power Management Control ECU
(for Sub Bus 11) |
Connection diagram
Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| O30-9 (CANH) | R | Blind spot monitor sensor RH*
(for Sub bus 11) |
| O30-20 (CANL) | B | |
| O30-10 (CANH) | G | CAN No. 3 junction connector
(for Sub bus 11) |
| O30-21 (CANL) | B | |
| O30-11 (CANH) | V | Power management control ECU
(for Sub bus 11) |
| O30-22 (CANL) | B |
*: w/ Blind Spot Monitor System
CAN NO. 3 JUNCTION CONNECTOR (w/o Parking Assist Monitor System without Parallel Parking Assist Function)
Check the CAN No. 3 junction connector.
| *a | Front view of wire harness connector
(to CAN No. 3 Junction Connector) |
| *b | to CAN No. 4 Junction Connector
(for Sub Bus 11) |
| *c | to Blind Spot Monitor Sensor LH
(w/ Blind Spot Monitor System) (for Sub Bus 11) |
| *d | to CAN No. 2 Junction Connector
(for Sub Bus 11) |
Connection diagram
Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| T15-9 (CANH) | L | CAN No. 4 junction connector
(for Sub bus 11) |
| T15-20 (CANL) | B | |
| T15-10 (CANH) | R | Blind spot monitor sensor LH*
(for Sub bus 11) |
| T15-21 (CANL) | B | |
| T15-11 (CANH) | G | CAN No. 2 junction connector
(for Sub bus 11) |
| T15-22 (CANL) | B |
*: w/ Blind Spot Monitor System
CAN NO. 3 JUNCTION CONNECTOR (w/ Parking Assist Monitor System without Parallel Parking Assist Function)
Check the CAN No. 3 junction connector.
| *a | Front view of wire harness connector
(to CAN No. 3 Junction Connector) |
| *b | to Rear Television Camera Assembly
(for Sub Bus 11) |
| *c | to CAN No. 4 Junction Connector
(for Sub Bus 11) |
| *d | to Blind Spot Monitor Sensor LH
(w/ Blind Spot Monitor System) (for Sub Bus 11) |
| *e | to CAN No. 2 Junction Connector
(for Sub Bus 11) |
Connection diagram
Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| T15-1 (CANH) | V | Rear television camera assembly
(for Sub bus 11) |
| T15-12 (CANL) | P | |
| T15-2 (CANH) | L | CAN No. 4 junction connector
(for Sub bus 11) |
| T15-13 (CANL) | B | |
| T15-3 (CANH) | R | Blind spot monitor sensor LH*
(for Sub bus 11) |
| T15-14 (CANL) | B | |
| T15-4 (CANH) | G | CAN No. 2 junction connector
(for Sub bus 11) |
| T15-15 (CANL) | B |
*: w/ Blind Spot Monitor System
CAN NO. 4 JUNCTION CONNECTOR
Check the CAN No. 4 junction connector.
| *a | Rear view of wire harness connector
(to CAN No. 4 Junction Connector) |
| *b | to CAN No. 3 Junction Connector
(for Sub Bus 11) |
Connection diagram
Check the connection diagram of the components which are connected to the CAN No. 4 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| T16-3 (CANH) | L | CAN No. 3 junction connector
(for Sub bus 11) |
| T16-2 (CANL) | B |
DLC3
Disconnect the cable from the negative (-) auxiliary battery terminal.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I39-6 (CANH) - I39-14 (CANL) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| I39-6 (CANH) - I39-4 (CG) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I39-14 (CANL) - I39-4 (CG) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I39-6 (CANH) - I39-16 (BAT) | G - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I39-14 (CANL) - I39-16 (BAT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
POWER MANAGEMENT CONTROL ECU
| *a | Component without harness connected
(Power Management Control ECU) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
Disconnect the I4 power management control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I4-25 (CA1H) - I4-24 (CA1L) | BE - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| I4-25 (CA1H) - I4-4 (E12) | BE - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I4-24 (CA1L) - I4-4 (E12) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I4-25 (CA1H) - I4-7 (AM21) | BE - L | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I4-24 (CA1L) - I4-7 (AM21) | W - L | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I4-31 (CA3P) - I4-30 (CA3N) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| I4-31 (CA3P) - I4-4 (E12) | B - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I4-30 (CA3N) - I4-4 (E12) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I4-31 (CA3P) - I4-7 (AM21) | B - L | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I4-30 (CA3N) - I4-7 (AM21) | W - L | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
Disconnect the I3 power management control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I3-34 (CA2H) - I3-35 (CA2L) | G - LG | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| I3-34 (CA2H) - I3-6 (E1) | G - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I3-35 (CA2L) - I3-6 (E1) | LG - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I3-34 (CA2H) - I3-1 (AM22) | G - SB | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I3-35 (CA2L) - I3-1 (AM22) | LG - SB | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
ECM
| *a | Component without harness connected
(ECM) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A25 and E28 ECM connectors.
| *a | Front view of wire harness connector
(to ECM) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A25-13 (CANH) - A25-26 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| A25-13 (CANH) - E28-16 (E1) | B - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A25-26 (CANL) - E28-16 (E1) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A25-13 (CANH) - A25-1 (BATT) | B - GR | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A25-26 (CANL) - A25-1 (BATT) | W - GR | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A25-12 (CANP) - A25-25 (CANN) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| A25-12 (CANP) - E28-16 (E1) | B - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A25-25 (CANN) - E28-16 (E1) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A25-12 (CANP) - A25-1 (BATT) | B - GR | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A25-25 (CANN) - A25-1 (BATT) | W - GR | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
COMBINATION METER ASSEMBLY
| *a | Component without harness connected
(Combination Meter Assembly) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the I18 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I18-16 (CANH) - I18-15 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| I18-16 (CANH) - I18-7 (ES) | R - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I18-15 (CANL) - I18-7 (ES) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I18-16 (CANH) - I18-1 (B) | R - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I18-15 (CANL) - I18-1 (B) | W - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *1 | Main Body ECU (Multiplex Network Body ECU)) | *2 | 2 connectors |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU)) |
- | - |
| *1 | Main Body ECU (Multiplex Network Body ECU)) | *2 | 3 connectors |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU)) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the I12 and I13 main body ECU (multiplex network body ECU) connectors.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU)) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I13-14 (CANH) - I13-13 (CANL) | P - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| I13-14 (CANH) - I39-4 (CG) | P - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I13-13 (CANL) - I39-4 (CG) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I13-14 (CANH) - I39-16 (BAT) | P - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I13-13 (CANL) - I39-16 (BAT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I12-9 (CANP) - I12-10 (CANN) | R - GR | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| I12-9 (CANP) - I39-4 (CG) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I12-10 (CANN) - I39-4 (CG) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I12-9 (CANP) - I39-16 (BAT) | R - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I12-10 (CANN) - I39-16 (BAT) | GR - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)
| *a | Component without harness connected
(Brake Booster with Master Cylinder Assembly (Skid Control ECU)) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU)) |
Disconnect the A28 brake booster with master cylinder assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A28-37 (CA1H) - A28-38 (CA1L) | GR - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A28-37 (CA1H) - A28-28 (GND) | GR - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A28-38 (CA1L) - A28-28 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A28-37 (CA1H) - A28-15 (BS) | GR - Y | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A28-38 (CA1L) - A28-15 (BS) | W - Y | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A28-35 (CA2H) - A28-34 (CA2L) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A28-35 (CA2H) - A28-28 (GND) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A28-34 (CA2L) - A28-28 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A28-35 (CA2H) - A28-15 (BS) | B - Y | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A28-34 (CA2L) - A28-15 (BS) | W - Y | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
STEERING SENSOR
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Steering Sensor) |
Disconnect the I30 steering sensor connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I30-3 (CANH) - I30-2 (CANL) | V - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| I30-3 (CANH) - I30-1 (ESS) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I30-2 (CANL) - I30-1 (ESS) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I30-3 (CANH) - I30-5 (BAT) | V - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I30-2 (CANL) - I30-5 (BAT) | W - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
POWER STEERING ECU ASSEMBLY
| *a | Component without harness connected
(Power Steering ECU Assembly) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the j2 and j3 power steering ECU assembly connectors.
| *a | Front view of wire harness connector
(to Power Steering ECU Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| j3-4 (CANH) - j3-8 (CANL) | Y - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| j3-4 (CANH) - j2-2 (PGND) | Y - B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| j3-8 (CANL) - j2-2 (PGND) | SB - B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| j3-4 (CANH) - j2-1 (PIG) | Y - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| j3-8 (CANL) - j2-1 (PIG) | SB - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
AIRBAG SENSOR ASSEMBLY
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the I47 airbag sensor assembly connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I47-13 (CANH) - I47-22 (CANL) | Y - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| I47-13 (CANH) - I47-25 (E1) | Y - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I47-22 (CANL) - I47-25 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I47-13 (CANH) - I39-16 (BAT) | Y - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I47-22 (CANL) - I39-16 (BAT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
SMART KEY ECU ASSEMBLY (CERTIFICATION ECU)
| *a | Component without harness connected
(Smart Key ECU Assembly (Certification ECU)) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the I86 and I87 smart key ECU assembly (certification ECU) connectors.
| *a | Front view of wire harness connector
(to Smart Key ECU Assembly (Certification ECU)) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I87-1 (CANH) - I87-2 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| I87-1 (CANH) - I86-1 (E) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I87-2 (CANL) - I86-1 (E) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I87-1 (CANH) - I87-5 (+B) | L - SB | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I87-2 (CANL) - I87-5 (+B) | W - SB | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)
| *a | Component without harness connected
(Radio and Display Receiver Assembly) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the I152 and I155 radio and display receiver assembly connectors.
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I155-9 (CANH) - I155-10 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| I155-9 (CANH) - I152-7 (GND1) | R - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I155-10 (CANL) - I152-7 (GND1) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I155-9 (CANH) - I152-4 (+B1) | R - L-Y | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I155-10 (CANL) - I152-4 (+B1) | W - L-Y | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
NAVIGATION ECU SUB-ASSEMBLY (for Navigation Receiver Type with HDD)
| *a | Component without harness connected
(Navigation ECU Sub-assembly) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the I64 and I67 navigation ECU sub-assembly connectors.
| *a | Front view of wire harness connector
(to Navigation ECU Sub-assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I67-9 (CANH) - I67-10 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| I67-9 (CANH) - I64-7 (GND1) | R - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I67-10 (CANL) - I64-7 (GND1) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I67-9 (CANH) - I64-4 (+B1) | R - L-Y | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I67-10 (CANL) - I64-4 (+B1) | W - L-Y | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type without HDD)
| *a | Component without harness connected
(Navigation Receiver Assembly) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the I64 and I67 navigation receiver assembly connectors.
| *a | Front view of wire harness connector
(to Navigation Receiver Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I67-9 (CANH) - I67-10 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| I67-9 (CANH) - I64-7 (GND1) | R - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I67-10 (CANL) - I64-7 (GND1) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I67-9 (CANH) - I64-4 (+B1) | R - L-Y | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I67-10 (CANL) - I64-4 (+B1) | W - L-Y | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY
| *a | Component without harness connected
(Air Conditioning Amplifier Assembly) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the I77 air conditioning amplifier assembly connector.
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I77-11 (CANH) - I77-12 (CANL) | V - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| I77-11 (CANH) - I77-14 (GND) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I77-12 (CANL) - I77-14 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I77-11 (CANH) - I77-21 (B) | V - Y | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I77-12 (CANL) - I77-21 (B) | W - Y | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
OUTER MIRROR CONTROL ECU ASSEMBLY (for Driver Side) (w/ Seat Position Memory System)
| *a | Component without harness connected
(Outer Mirror Control ECU Assembly (for Driver Side)) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Driver Side)) |
Disconnect the J13 outer mirror control ECU assembly (for driver side) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| J13-9 (CANP) - J13-8 (CANN) | P - GR | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| J13-9 (CANP) - J13-7 (GND) | P - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| J13-8 (CANN) - J13-7 (GND) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| J13-9 (CANP) - J13-6 (CPUB) | P - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| J13-8 (CANN) - J13-6 (CPUB) | GR - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
OUTER MIRROR CONTROL ECU ASSEMBLY (for Front Passenger Side) (w/ Seat Position Memory System)
| *a | Component without harness connected
(Outer Mirror Control ECU Assembly (for Front Passenger Side)) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Front Passenger Side)) |
Disconnect the K12 outer mirror control ECU assembly (for front passenger side) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| K12-9 (CANP) - K12-8 (CANN) | G - GR | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| K12-9 (CANP) - K12-7 (GND) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| K12-8 (CANN) - K12-7 (GND) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| K12-9 (CANP) - K12-6 (CPUB) | G - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| K12-8 (CANN) - K12-6 (CPUB) | GR - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
POSITION CONTROL ECU AND SWITCH ASSEMBLY (for Driver Side) (w/ Seat Position Memory System)
| *a | Component without harness connected
(Position Control ECU and Switch Assembly (for Driver Side)) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the d11 and d12 position control ECU and switch assembly (for driver side) connectors.
| *a | Front view of wire harness connector
(to Position Control ECU and Switch Assembly (for Driver Side)) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| d12-8 (CANP) - d12-7 (CANN) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| d12-8 (CANP) - d11-2 (GND) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| d12-7 (CANN) - d11-2 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| d12-8 (CANP) - d11-7 (+B) | L - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| d12-7 (CANN) - d11-7 (+B) | W - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)
| *a | Component without harness connected
(Blind Spot Monitor Sensor LH) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the T10 blind spot monitor sensor LH connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| T10-8 (CA1P) - T10-4 (CA1N) | R - B | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| T10-8 (CA1P) - T10-1 (BLGD) | R - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| T10-4 (CA1N) - T10-1 (BLGD) | B - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| T10-8 (CA1P) - I39-16 (BAT) | R - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| T10-4 (CA1N) - I39-16 (BAT) | B - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
BLIND SPOT MONITOR SENSOR RH (w/ Blind Spot Monitor System)
| *a | Component without harness connected
(Blind Spot Monitor Sensor RH) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the O28 blind spot monitor sensor RH connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor RH) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| O28-8 (CA1P) - O28-4 (CA1N) | R - B | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| O28-8 (CA1P) - O28-1 (BRGD) | R - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| O28-4 (CA1N) - O28-1 (BRGD) | B - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| O28-8 (CA1P) - I39-16 (BAT) | R - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| O28-4 (CA1N) - I39-16 (BAT) | B - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
HEADLIGHT SWIVEL ECU ASSEMBLY (AFS ECU) (w/ Automatic High Beam System)
| *a | Component without harness connected
(Headlight Swivel ECU Assembly (AFS ECU)) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A35 headlight swivel ECU assembly (AFS ECU) connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Headlight Swivel ECU Assembly (AFS ECU)) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A35-12 (MPX1) - A35-13 (MPX2) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A35-12 (MPX1) - A35-22 (E1) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A35-13 (MPX2) - A35-22 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A35-12 (MPX1) - I39-16 (BAT) | B - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A35-13 (MPX2) - I39-16 (BAT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
REAR TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System without Parallel Parking Assist Function)
| *a | Component without harness connected
(Rear Television Camera Assembly) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the T22 rear television camera assembly connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Rear Television Camera Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| T22-4 (CANH) - T22-1 (CANL) | V - P | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| T22-4 (CANH) - I39-4 (CG) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| T22-1 (CANL) - I39-4 (CG) | P - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| T22-4 (CANH) - I39-16 (BAT) | V - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| T22-1 (CANL) - I39-16 (BAT) | P - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |