Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2015.04
RM2040EQ _59 Vehicle Exterior _014738 LIGHTING (EXT) _0075173 LIGHTING SYSTEM U

LIGHTING (EXT)  LIGHTING SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuator and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / (desired system) / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Dimmer SW Dimmer switch high position signal ON or OFF ON: Dimmer switch in high or high flash position
OFF: Dimmer switch in low position
-
Passing Light SW Dimmer switch high flash position (pass) signal ON or OFF ON: Dimmer switch in high flash position
OFF: Dimmer switch not in high flash position
-
Auto Light SW Light control switch AUTO position signal ON or OFF ON: Light control switch in AUTO position
OFF: Light control switch not in AUTO position
-
Head Light SW (Head) Light control switch head position signal ON or OFF ON: Light control switch in head position
OFF: Light control switch not in head position
-
Head Light SW (Tail) Light control switch tail position signal ON or OFF ON: Light control switch in tail or head position
OFF: Light control switch in neither tail nor head position
-
Illumination Rate Info Illumination rate information 0.00 ms. to 2162.65 ms. Value is output according to ambient light levels -
Response Time Delay timing of lighting the taillights when the automatic light control sensor detects brightness change Normal or Long Customize setting displayed -
Sensitivity Sensitivity of the automatic light control system Light2, Light1, Normal, Dark1 or Dark2 Customize setting displayed -
Disp Ex ON Sen Ambient brightness level required to dim display lights (combination meter, navigation display etc.) Light2, Light1, Normal, Dark1 or Dark2 Customize setting displayed -
Disp Ex OFF Sen Ambient brightness level required to cancel dimming display lights (combination meter, navigation display etc.) Light2, Light1, Normal, Dark1 or Dark2 Customize setting displayed -
Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Turn Signal Switch (Right) Turn signal switch (Right) signal ON or OFF ON: Turn signal switch (Right) on
OFF: Turn signal switch (Right) off
-
Turn Signal Switch (Left) Turn signal switch (Left) signal ON or OFF ON: Turn signal switch (Left) on
OFF: Turn signal switch (Left) off
-
Hazard Flasher Switch Hazard switch signal ON or OFF ON: Hazard switch on
OFF: Hazard switch off
-


ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Daytime Running Light Daytime running lights ON/OFF -
Taillight Relay Taillight relay ON/OFF -
Headlight Relay Headlight relays ON/OFF -
Head Light Hi High beam headlights ON/OFF -
Dimmer Signal Dimmer signal ON/OFF -