Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.04
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Turn the power switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.

·

Turn the power switch off before inspecting CAN bus lines for a ground short.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



CAN JUNCTION LH1 CONNECTOR


a.

Check the CAN junction LH1 connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.


i.

Connection diagram

C239444C18
5.156,0.667 4.281,0.667 4.281,0.667 4.281,1.188 true 5.573,0.896 4.563,0.896 4.563,0.896 4.563,1.188 true 4.74,0.448 4.01,0.448 4.01,0.448 4.01,1.188 true 4.313,0.219 3.74,0.219 3.74,0.219 3.74,1.188 true 5.156,2.125 4.281,2.125 4.281,2.125 4.281,1.365 true 5.573,1.896 4.563,1.896 4.563,1.896 4.563,1.365 true 4.74,2.344 4.01,2.344 4.01,2.344 4.01,1.365 true 4.313,2.573 3.74,2.573 3.74,2.573 3.74,1.365 true 2.01,0.656 2.885,0.656 2.885,0.656 2.885,1.177 true 1.594,0.885 2.615,0.885 2.615,0.885 2.615,1.177 true 2.427,0.438 3.156,0.438 3.156,0.438 3.156,1.177 true 2.854,0.208 3.427,0.208 3.427,0.208 3.427,1.177 true 2,2.125 2.875,2.125 2.875,2.125 2.875,1.365 true 1.583,1.896 2.604,1.896 2.604,1.896 2.604,1.365 true 2.417,2.344 3.146,2.344 3.146,2.344 3.146,1.365 true 2.844,2.573 3.417,2.573 3.417,2.573 3.417,1.365 true 0.146,0.125 0.313,0.281 0.167,0.156 10 false *a 4.354,0.125 4.958,0.354 0.604,0.229 10 false CANH*f 4.771,0.354 5.417,0.552 0.646,0.198 10 false CANH*g 5.198,0.573 6.24,0.76 1.042,0.188 10 false CANH*h*i 5.188,2.042 6.156,2.333 0.969,0.292 10 false CANL*h*i 4.76,2.271 5.406,2.5 0.646,0.229 10 false CANL*g 4.344,2.49 4.896,2.646 0.552,0.156 10 false CANL*f 5.604,0.813 6.281,1.031 0.677,0.219 10 false CANH*j 5.604,1.823 6.156,1.979 0.552,0.156 10 false CANL*j 2.302,0.125 2.854,0.281 0.552,0.156 10 false CANH*e 1.875,0.354 2.427,0.51 0.552,0.156 10 false CANH*d 1.458,0.573 2.01,0.729 0.552,0.156 10 false CANH*c 1.458,2.042 2.01,2.198 0.552,0.156 10 false CANL*c 1.875,2.271 2.427,2.427 0.552,0.156 10 false CANL*d 2.302,2.49 2.854,2.646 0.552,0.156 10 false CANL*e 1.042,0.823 1.594,0.979 0.552,0.156 10 false CANH*b 1.042,1.823 1.594,1.979 0.552,0.156 10 false CANL*b
*a Component with harness connected
(CAN Junction LH1 Connector)
*b to Power Management Control ECU
(for V Bus)
*c to Main Body ECU (Multiplex Network Body ECU)
(for V Bus)
*d to Air Conditioning Amplifier Assembly
(for V Bus)
*e to Airbag Sensor Assembly
(for V Bus)
*f to Power Steering ECU Assembly
(for V Bus)
*g to ECM
(for V Bus)
*h Navigation Receiver Assembly
(for Navigation Receiver Type)
(for V Bus)
*i Radio and Display Receiver Assembly
(for Radio and Display Type)
(for V Bus)
*j to CAN Junction RH1 Connector
(for V Bus)



ii.

Check the connection diagram of the components which are connected to the CAN junction LH1 connector.

Terminal No. (Symbol) Wiring Color Connected to
I109-1 (CANH) BE Power management control ECU
(for V bus)
I109-2 (CANL) W
I95-1 (CANH) P Main body ECU (Multiplex network body ECU)
(for V bus)
I95-2 (CANL) W
I102-1 (CANH) V Air conditioning amplifier assembly
(for V bus)
I102-2 (CANL) W
I103-1 (CANH) Y Airbag sensor assembly
(for V bus)
I103-2 (CANL) W
I100-1 (CANH) L Power steering ECU assembly
(for V bus)
I100-2 (CANL) W
I104-1 (CANH) G ECM
(for V bus)
I104-2 (CANL) W
I107-1 (CANH) R Navigation receiver assembly*1
(for V bus)
I107-2 (CANL) W
I107-1 (CANH) R Radio and display receiver assembly*2
(for V bus)
I107-2 (CANL) W
I93-1 (CANH) B CAN junction RH1 connector
(for V bus)
I93-2 (CANL) W

·

*1: for Navigation Receiver Type

·

*2: for Radio and Display Type





CAN JUNCTION RH1 CONNECTOR


a.

Check the CAN junction RH1 connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.


i.

Connection diagram

C248091C09
5.135,0.677 4.26,0.677 4.26,0.677 4.26,1.188 true 5.583,0.896 4.563,0.896 4.563,0.896 4.563,1.188 true 4.74,0.448 4.01,0.448 4.01,0.448 4.01,1.188 true 4.323,0.219 3.74,0.219 3.74,0.219 3.74,1.188 true 5.156,2.125 4.281,2.125 4.281,2.125 4.281,1.365 true 5.583,1.896 4.563,1.896 4.563,1.896 4.563,1.365 true 4.74,2.354 4.01,2.354 4.01,2.354 4.01,1.365 true 4.323,2.573 3.74,2.573 3.74,2.573 3.74,1.365 true 2,0.677 2.875,0.677 2.875,0.677 2.875,1.188 true 2.438,0.438 3.156,0.438 3.156,0.438 3.156,1.177 true 2.854,0.219 3.427,0.219 3.427,0.219 3.427,1.188 true 2,2.125 2.875,2.125 2.875,2.125 2.875,1.365 true 2.417,2.354 3.135,2.354 3.135,2.354 3.135,1.365 true 2.833,2.573 3.406,2.573 3.406,2.573 3.406,1.365 true 0.146,0.125 0.313,0.281 0.167,0.156 10 false *a 4.385,0.125 4.938,0.281 0.552,0.156 10 false CANH*e 4.813,0.354 5.365,0.51 0.552,0.156 10 false CANH*f 5.24,0.594 5.896,0.781 0.656,0.188 10 false CANH*g 5.229,2.042 5.958,2.24 0.729,0.198 10 false CANL*g 4.802,2.271 5.531,2.469 0.729,0.198 10 false CANL*f 4.417,2.5 5.115,2.698 0.698,0.198 10 false CANL*e 5.656,0.823 6.208,0.979 0.552,0.156 10 false CANH*h 5.625,1.813 6.177,1.969 0.552,0.156 10 false CANL*h 2.302,0.146 2.854,0.302 0.552,0.156 10 false CANH*d 1.885,0.354 2.438,0.51 0.552,0.156 10 false CANH*c 1.448,0.604 2,0.76 0.552,0.156 10 false CANH*b 1.469,2.031 2.021,2.188 0.552,0.156 10 false CANL*b 1.896,2.25 2.448,2.406 0.552,0.156 10 false CANL*c 2.313,2.469 2.969,2.635 0.656,0.167 10 false CANL*d
*a Component with harness connected
(CAN Junction RH1 Connector)
*b to Clearance Warning ECU Assembly
(w/ Toyota Parking Assist-sensor System)
(for V Bus)
*c to Steering Sensor
(for V Bus)
*d to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for V Bus)
*e to Smart Key ECU Assembly (Certification ECU)
(for V Bus)
*f to DLC3
(for V Bus)
*g to Combination Meter Assembly
(for V Bus)
*h to CAN Junction LH1 Connector
(for V Bus)



ii.

Check the connection diagram of the components which are connected to the CAN junction RH1 connector.

Terminal No. (Symbol) Wiring Color Connected to
I177-1 (CANH) P Clearance warning ECU assembly*
(for V bus)
I177-2 (CANL) W
I97-1 (CANH) V Steering sensor
(for V bus)
I97-2 (CANL) W
I110-1 (CANH) Y Brake booster with master cylinder assembly (Skid control ECU)
(for V bus)
I110-2 (CANL) W
I106-1 (CANH) L Smart key ECU assembly (Certification ECU)
(for V bus)
I106-2 (CANL) W
I96-1 (CANH) G DLC3
(for V bus)
I96-2 (CANL) W
I94-1 (CANH) R Combination meter assembly
(for V bus)
I94-2 (CANL) W
I101-1 (CANH) B CAN junction LH1 connector
(for V bus)
I101-2 (CANL) W

*: w/ Toyota Parking Assist-sensor System





CAN JUNCTION LH2 CONNECTOR (w/ Seat Position Memory System)


a.

Check the CAN junction LH2 connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.


i.

Connection diagram

C247999C17
6.198,1.74 6.469,2.542 true 1.135,4.688 1.573,4.531 true 1.583,5.031 1.146,4.875 true 0.083,0.094 0.531,0.417 0.448,0.323 10 false *1 1.354,0.656 1.802,0.979 0.448,0.323 10 false *a 4.427,0.656 4.865,0.979 0.438,0.323 10 false *b 6.406,2.563 6.854,2.885 0.448,0.323 10 false *c 0.563,4.094 1.01,4.417 0.448,0.323 10 false *d 1.615,4.458 2.146,4.688 0.531,0.229 10 false CANH 1.615,4.969 2.146,5.198 0.531,0.229 10 false CANL 4.615,4.833 5.073,5.042 0.458,0.208 10 false I162 4.615,4.469 5.073,4.677 0.458,0.208 10 false I163 4.615,5.188 5.073,5.396 0.458,0.208 10 false I166
*1 CAN Junction LH2 Connector - -
*a Junction Connector A Side *b Junction Connector B Side
*c Earth Terminal *d Front view of wire harness connector
(to CAN Junction LH2 Connector)




b.

Check the connection diagram of the components which are connected to the CAN junction LH2 connector.

Junction Connector B Side
Terminal No. (Symbol) Wiring Color Connected to
I162-1 (CANH) R Main body ECU (Multiplex network body ECU)
(for Sub bus 1)
I162-2 (CANL) GR
I163-1 (CANH) G Outer mirror control ECU assembly (for Front passenger side)
(for Sub bus 1)
I163-2 (CANL) GR
I166-1 (CANH) Y CAN junction RH2 connector
(for Sub bus 1)
I166-2 (CANL) GR



CAN JUNCTION RH2 CONNECTOR (w/ Seat Position Memory System)


a.

Check the CAN junction RH2 connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.


i.

Connection diagram

C259930C05
6.198,1.74 6.469,2.542 false 1.135,4.688 1.573,4.542 false 1.573,5.031 1.135,4.875 false 0.094,0.073 0.531,0.396 0.438,0.323 10 false *1 1.354,0.646 1.792,0.969 0.438,0.323 10 false *a 4.438,0.656 4.875,0.979 0.438,0.323 10 false *b 6.406,2.563 6.844,2.885 0.438,0.323 10 false *c 0.563,4.052 1,4.375 0.438,0.323 10 false *d 1.594,4.458 2.125,4.688 0.531,0.229 10 false CANH 1.594,4.969 2.125,5.198 0.531,0.229 10 false CANL 4.615,4.833 5.073,5.042 0.458,0.208 10 false I164 4.615,4.469 5.073,4.677 0.458,0.208 10 false I165 4.615,3.75 5.073,3.958 0.458,0.208 10 false I168 4.615,5.177 5.073,5.385 0.458,0.208 10 false I167
*1 CAN Junction RH2 Connector - -
*a Junction Connector A Side *b Junction Connector B Side
*c Earth Terminal *d Front view of wire harness connector
(to CAN Junction RH2 Connector)




b.

Check the connection diagram of the components which are connected to the CAN junction RH2 connector.

Junction Connector B Side
Terminal No. (Symbol) Wiring Color Connected to
I168-1 (GND) W-B Body ground
I167-1 (CANH) Y CAN junction LH2 connector
(for Sub bus 1)
I167-2 (CANL) GR
I165-1 (CANH) BE Position control ECU and switch assembly (for Driver side)
(for Sub bus 1)
I165-2 (CANL) GR
I164-1 (CANH) P Outer mirror control ECU assembly (for Driver side)
(for Sub bus 1)
I164-2 (CANL) GR



CAN NO. 1 JUNCTION CONNECTOR


a.

Check the CAN No. 1 junction connector.

i.

Connection diagram

C234761C37
3.438,0.167 3.823,0.417 0.385,0.25 3.188,1.417 2.5,0.927 2.5,0.927 2.167,0.927 true 3.354,1.406 2.521,0.531 2.521,0.531 2.188,0.531 true 3.219,1.719 2.531,2.094 2.531,2.094 2.198,2.094 true 3.365,1.719 2.531,2.438 2.531,2.438 2.198,2.438 true 3.5,1.406 4.302,0.531 4.302,0.531 4.604,0.531 true 3.51,1.719 4.313,2.438 4.313,2.438 4.615,2.438 true 0.115,0.083 0.49,0.625 0.375,0.542 10 false *a 1.635,0.427 2.396,0.677 0.76,0.25 10 false CANH*c 1.677,2.365 2.417,2.604 0.74,0.24 10 false CANL*c 1.583,0.823 2.333,1.094 0.75,0.271 10 false CANH*b 1.688,2.031 2.417,2.271 0.729,0.24 10 false CANL*b 4.688,0.427 5.333,0.667 0.646,0.24 10 false CANH*d 4.688,2.375 5.333,2.615 0.646,0.24 10 false CANL*d 3.5,0.198 4.385,0.521 0.885,0.323 10 false A72
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for Sub Bus 15)
*c to ECM
(for Sub Bus 15)
*d to Power Management Control ECU
(for Sub Bus 15)



ii.

Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A72-1 (CANH) B Brake booster with master cylinder assembly (Skid control ECU)
(for Sub bus 15)
A72-7 (CANL) W
A72-2 (CANH) B ECM
(for Sub bus 15)
A72-8 (CANL) W
A72-3 (CANH) B Power management control ECU
(for Sub bus 15)
A72-9 (CANL) W




CAN NO. 2 JUNCTION CONNECTOR


a.

Check the CAN No. 2 junction connector.

i.

Connection diagram

C281852C82
3.115,0.563 3.583,0.833 0.469,0.271 4,2.125 4.406,1.917 4.406,1.917 4.865,1.917 true 3.979,2.385 4.344,2.594 4.344,2.594 4.813,2.594 true 3.594,2.406 4.177,3.115 4.177,3.115 4.469,3.115 true 3.729,2.406 4.365,2.865 4.365,2.865 4.656,2.865 true 3.594,2.135 4.219,1.167 4.219,1.167 4.531,1.167 true 3.729,2.146 4.417,1.5 4.417,1.5 4.729,1.5 true 0.083,0.073 0.51,0.49 0.427,0.417 10 false *a 4.552,3.042 5.167,3.24 0.615,0.198 10 false CANL*b 4.625,1.094 5.24,1.292 0.615,0.198 10 false CANH*b 3.229,0.625 3.844,0.823 0.615,0.198 10 false O30 4.75,2.792 5.365,2.99 0.615,0.198 10 false CANL*c 4.896,2.521 5.51,2.719 0.615,0.198 10 false CANL*d 5,1.854 5.615,2.052 0.615,0.198 10 false CANH*d 4.813,1.438 5.427,1.635 0.615,0.198 10 false CANH*c
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 3 Junction Connector
(for Sub Bus 11)
*c to Blind Spot Monitor Sensor RH
(w/ Blind Spot Monitor System)
(for Sub Bus 11)
*d to CAN No. 6 Junction Connector
(for Sub Bus 11)



ii.

Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
O30-8 (CANH) G CAN No. 3 junction connector
(for Sub bus 11)
O30-19 (CANL) B
O30-9 (CANH) R Blind spot monitor sensor RH*
(for Sub bus 11)
O30-20 (CANL) B
O30-11 (CANH) V CAN No. 6 junction connector
(for Sub bus 11)
O30-22 (CANL) B

*: w/ Blind Spot Monitor System





CAN NO. 3 JUNCTION CONNECTOR


a.

Check the CAN No. 3 junction connector.

i.

Connection diagram

C281852C83
3.115,0.688 3.583,0.958 0.469,0.271 2.708,2.135 2.49,1.708 2.49,1.708 2.25,1.708 true 2.833,2.125 2.552,1.24 2.552,1.24 2.313,1.24 true 2.823,2.406 2.583,2.948 2.583,2.948 2.375,2.948 true 2.698,2.396 2.521,2.719 2.521,2.719 2.333,2.719 true 2.958,2.125 2.698,0.948 2.698,0.948 2.51,0.948 true 2.958,2.406 2.635,3.198 2.635,3.198 2.469,3.198 true 0.083,0.073 0.51,0.49 0.427,0.417 10 false *a 1.854,2.875 2.469,3.073 0.615,0.198 10 false CANL*c 1.74,1.156 2.354,1.354 0.615,0.198 10 false CANH*c 1.948,0.865 2.563,1.063 0.615,0.198 10 false CANH*d 1.958,3.125 2.573,3.323 0.615,0.198 10 false CANL*d 1.656,1.635 2.271,1.833 0.615,0.198 10 false CANH*b 1.802,2.635 2.417,2.833 0.615,0.198 10 false CANL*b 3.24,0.74 3.854,0.938 0.615,0.198 10 false T15
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to CAN No. 4 Junction Connector
(for Sub Bus 11)
*c to Rear Television Camera Assembly
(w/ Parking Assist Monitor System without Parallel Parking Assist Function)
(for Sub Bus 11)
*d to CAN No. 2 Junction Connector
(for Sub Bus 11)



ii.

Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
T15-1 (CANH) L CAN No. 4 junction connector
(for Sub bus 11)
T15-12 (CANL) B
T15-2 (CANH) V Rear television camera assembly*
(for Sub bus 11)
T15-13 (CANL) P
T15-3 (CANH) G CAN No. 2 junction connector
(for Sub bus 11)
T15-14 (CANL) B

*: w/ Parking Assist Monitor System without Parallel Parking Assist Function





CAN NO. 4 JUNCTION CONNECTOR


a.

Check the CAN No. 4 junction connector.

i.
C183982C41
1.781,2.063 2.198,2.302 0.417,0.24 0.938,0.844 0.635,0.844 0.635,0.844 0.635,2.177 true 1.219,1.188 0.917,1.188 0.917,1.188 0.917,2.177 true 0.177,0.115 0.333,0.292 0.156,0.177 10 false *a 0.99,0.75 1.563,0.906 0.573,0.156 10 false CANH*b 1.271,1.104 1.833,1.26 0.563,0.156 10 false CANL*b 1.875,2.104 2.438,2.5 0.563,0.396 10 false T16
*a Rear view of wire harness connector
(to CAN No. 4 Junction Connector)
*b to CAN No. 3 Junction Connector
(for Sub Bus 11)


Connection diagram


ii.

Check the connection diagram of the components which are connected to the CAN No. 4 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
T16-3 (CANH) L CAN No. 3 junction connector
(for Sub bus 11)
T16-2 (CANL) B




CAN NO. 5 JUNCTION CONNECTOR


a.

Check the CAN No. 5 junction connector.

i.

Connection diagram

C234761C38
2.313,1.198 2.76,1.438 0.448,0.24 3.219,1.406 3.219,0.677 3.219,0.677 2.844,0.677 true 3.365,1.406 3.365,0.26 3.365,0.26 3.74,0.26 true 3.365,1.708 3.365,2.542 3.365,2.542 3.74,2.542 true 3.219,1.708 3.219,2.427 3.219,2.427 2.854,2.427 true 3.5,1.396 3.5,0.583 3.5,0.583 4.417,0.583 true 3.5,1.719 3.5,2.281 3.5,2.281 4.49,2.281 true 0.104,0.073 0.479,0.354 0.375,0.281 10 false *a 2.25,0.615 3.094,0.927 0.844,0.313 10 false CANH*b 2.302,2.354 3.146,2.667 0.844,0.313 10 false CANL*b 3.823,0.177 4.667,0.49 0.844,0.313 10 false CANH*c 3.802,2.458 4.646,2.771 0.844,0.313 10 false CANL*c 2.406,1.25 2.885,1.583 0.479,0.333 10 false S16 4.5,0.49 5.344,0.802 0.844,0.313 10 false CANH*d 4.552,2.198 5.396,2.51 0.844,0.313 10 false CANL*d
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to Lane Departure Warning Camera
(w/ Lane Departure Alert System)
(for Sub Bus 11)
*c to CAN No. 6 Junction Connector
(for Sub Bus 11)
*d to Power Management Control ECU
(for Sub Bus 11)



ii.

Check the connection diagram of the components which are connected to the CAN No. 5 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
S16-1 (CANH) V Lane departure warning camera*
(for Sub bus 11)
S16-7 (CANL) LG
S16-2 (CANH) R CAN No. 6 junction connector
(for Sub bus 11)
S16-8 (CANL) LG
S16-3 (CANH) B Power management control ECU
(for Sub bus 11)
S16-9 (CANL) LG

*: w/ Lane Departure Alert System





CAN NO. 6 JUNCTION CONNECTOR


a.

Check the CAN No. 6 junction connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.


i.

Connection diagram

C258642C13
6.198,1.74 6.469,2.542 true 1.135,4.688 1.573,4.531 true 1.583,5.021 1.146,4.865 true 0.135,0.146 0.573,0.469 0.438,0.323 10 false *1 1.354,0.667 1.792,0.99 0.438,0.323 10 false *a 4.417,0.667 4.854,0.99 0.438,0.323 10 false *b 6.438,2.563 6.875,2.885 0.438,0.323 10 false *c 0.563,4.042 1,4.365 0.438,0.323 10 false *d 1.625,4.427 2.156,4.656 0.531,0.229 10 false CANH 1.635,4.958 2.167,5.188 0.531,0.229 10 false CANL 4.615,4.479 5.073,4.688 0.458,0.208 10 false I179 4.615,4.833 5.073,5.042 0.458,0.208 10 false I178 4.615,4.115 5.073,4.323 0.458,0.208 10 false I180
*1 CAN No. 6 Junction Connector - -
*a Junction Connector A Side *b Junction Connector B Side
*c Earth Terminal *d Front view of wire harness connector
(to CAN No. 6 Junction Connector)




b.

Check the connection diagram of the components which are connected to the CAN No. 6 junction connector.

Junction Connector B Side
Terminal No. (Symbol) Wiring Color Connected to
I178-1 (CANH) V CAN No. 2 junction connector
(for Sub bus 11)
I178-2 (CANL) LG
I179-1 (CANH) L Driving support ECU assembly*
(for Sub bus 11)
I179-2 (CANL) LG
I180-1 (CANH) R CAN No. 5 junction connector
(for Sub bus 11)
I180-2 (CANL) LG

*: w/ Pre-crash Safety System




DLC3


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C188081C33
1.5,1.552 1.875,1.771 0.375,0.219 4.198,1.969 4.365,2.344 4.365,2.344 4.5,2.344 true 4.26,0.875 4.042,0.875 4.042,0.875 3.833,1.406 true 3.01,0.906 3.198,0.906 3.198,0.906 3.469,1.406 true 3.844,1.969 3.708,2.354 3.708,2.354 3.552,2.354 true 0.188,0.167 0.708,0.333 0.521,0.167 10 false *1 1.594,1.573 1.917,1.781 0.323,0.208 10 false I39 3.104,2.292 3.552,2.458 0.448,0.167 10 false CANL 4.333,0.802 4.781,0.969 0.448,0.167 10 false CANH 4.573,2.271 4.927,2.438 0.354,0.167 10 false BAT 2.729,0.833 3.083,1 0.354,0.167 10 false CG
*1 DLC3 - -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I39-6 (CANH) - I39-14 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I39-6 (CANH) - I39-4 (CG) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I39-14 (CANL) - I39-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I39-6 (CANH) - I39-16 (BAT) G - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I39-14 (CANL) - I39-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POWER MANAGEMENT CONTROL ECU


C274300C25
1.375,0.333 1.792,0.583 0.417,0.25 2.75,0.333 3.167,0.583 0.417,0.25 4.167,0.333 4.583,0.583 0.417,0.25 5.417,0.333 5.833,0.583 0.417,0.25 5.281,1.417 5.677,1.938 5.677,1.938 5.885,1.938 true 5.281,1.552 5.698,2.313 5.698,2.313 5.875,2.313 true 5.167,1.417 4.865,2 4.865,2 4.667,2 true 5.177,1.552 5.125,2.365 5.125,2.365 4.885,2.365 true 3.823,1.531 3.729,2.115 3.729,2.115 3.573,2.115 true 3.938,1.542 3.813,2.323 3.813,2.323 3.542,2.323 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.458,0.365 1.979,0.698 0.521,0.333 10 false A38 2.833,0.365 3.354,0.698 0.521,0.333 10 false A39 4.313,0.375 4.833,0.708 0.521,0.333 10 false I3 5.573,0.365 6.094,0.698 0.521,0.333 10 false I4 3.167,2.021 3.917,2.24 0.75,0.219 10 false CA2H 3.177,2.229 3.927,2.448 0.75,0.219 10 false CA2L 4.271,1.906 5.021,2.125 0.75,0.219 10 false CA1H 5.948,1.844 6.698,2.063 0.75,0.219 10 false CA1L 4.49,2.271 5.24,2.49 0.75,0.219 10 false CA3P 5.927,2.219 6.677,2.438 0.75,0.219 10 false CA3N
*a Component without harness connected
(Power Management Control ECU)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
A204446C75
2.438,2.885 2.927,3.177 0.49,0.292 2.469,2.51 1.646,2.219 true 2.417,2.51 1.667,2.458 true 2.427,2.365 2.104,2.104 true 2.625,2.365 3.01,2.083 true 1.698,2.771 2.417,2.573 true 1.75,3.052 2.469,2.573 true 2.615,2.948 3.052,3.24 0.438,0.292 10 false I4 1.281,2.115 1.729,2.365 0.448,0.25 10 false CA1L 1.271,2.396 1.802,2.635 0.531,0.24 10 false CA1H 1.292,2.698 1.76,2.979 0.469,0.281 10 false CA3P 1.333,2.99 1.875,3.26 0.542,0.271 10 false CA3N 0.135,0.125 0.458,0.406 0.323,0.281 10 false *a 1.729,2 2.219,2.26 0.49,0.26 10 false AM21 3.052,1.958 3.417,2.177 0.365,0.219 10 false E12
*a Rear view of wire harness connector
(to Power Management Control ECU)


Disconnect the I4 power management control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I4-25 (CA1H) - I4-24 (CA1L) BE - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I4-25 (CA1H) - I4-4 (E12) BE - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I4-24 (CA1L) - I4-4 (E12) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I4-25 (CA1H) - I4-7 (AM21) BE - L HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I4-24 (CA1L) - I4-7 (AM21) W - L LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 15 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I4-31 (CA3P) - I4-30 (CA3N) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
I4-31 (CA3P) - I4-4 (E12) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I4-30 (CA3N) - I4-4 (E12) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I4-31 (CA3P) - I4-7 (AM21) B - L HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I4-30 (CA3N) - I4-7 (AM21) W - L LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



d.
A317801C26
1.938,3.01 2.302,3.26 0.365,0.25 1.479,2.208 1.833,2.365 true 1.531,2.552 1.813,2.573 true 1.531,2.885 1.865,2.583 true 2.24,2.365 2.479,2.271 true 0.167,0.177 0.479,0.375 0.313,0.198 10 false *a 1.271,2.135 1.771,2.417 0.5,0.281 10 false E1 1.135,2.49 1.594,2.708 0.458,0.219 10 false CA2H 1.188,2.823 1.646,3.042 0.458,0.219 10 false CA2L 2.542,2.146 3,2.365 0.458,0.219 10 false AM22 2.063,3.052 2.521,3.271 0.458,0.219 10 false I3
*a Rear view of wire harness connector
(to Power Management Control ECU)


Disconnect the I3 power management control ECU connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Sub Bus 11 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I3-35 (CA2H) - I3-34 (CA2L) B - LG HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
I3-35 (CA2H) - I3-6 (E1) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I3-34 (CA2L) - I3-6 (E1) LG - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I3-35 (CA2H) - I3-1 (AM22) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I3-34 (CA2L) - I3-1 (AM22) LG - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




ECM


A262466C21
2.479,0.406 2.854,0.635 0.375,0.229 5.969,0.406 6.344,0.635 0.375,0.229 4.99,0.646 5.125,0.646 5.125,0.646 5.125,1.156 true 5.375,0.646 5.25,0.646 5.25,0.646 5.25,1.156 true 4.927,2.063 5.125,2.063 5.125,2.063 5.125,1.302 true 5.438,2.063 5.229,2.063 5.229,2.063 5.229,1.302 true 2.552,0.438 2.875,0.604 0.323,0.167 10 false E28 6.031,0.438 6.354,0.604 0.323,0.167 10 false A25 0.083,0.094 0.74,0.469 0.656,0.375 10 false *a 4.573,0.542 5.031,0.708 0.458,0.167 10 false CANH 5.448,0.542 5.906,0.708 0.458,0.167 10 false CANP 5.5,1.969 5.958,2.135 0.458,0.167 10 false CANN 4.531,1.979 4.99,2.146 0.458,0.167 10 false CANL
*a Component without harness connected
(ECM)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A25 and E28 ECM connectors.

C250518C23
1.813,0.49 2.208,0.729 0.396,0.24 4.313,0.5 4.708,0.74 0.396,0.24 5.104,0.615 4.813,0.615 4.813,0.615 4.813,1.26 true 2.813,0.615 2.51,0.615 2.51,0.615 2.51,1.25 true 2.75,0.302 2.448,0.302 2.448,0.302 2.448,1.25 true 2.813,2.156 2.51,2.156 2.51,2.156 2.51,1.313 true 2.74,2.49 2.448,2.49 2.448,2.49 2.448,1.313 true 1.24,0.615 1.531,0.615 1.531,0.615 1.531,1.25 true 0.146,0.125 0.313,0.281 0.167,0.156 10 false *a 5.146,0.542 5.333,0.698 0.188,0.156 10 false E1 2.854,0.542 3.271,0.698 0.417,0.156 10 false CANH 2.781,0.219 3.198,0.375 0.417,0.156 10 false CANP 2.854,2.083 3.271,2.24 0.417,0.156 10 false CANL 2.781,2.417 3.198,2.573 0.417,0.156 10 false CANN 0.844,0.542 1.302,0.698 0.458,0.156 10 false BATT 1.885,0.521 2.167,0.698 0.281,0.177 10 false A25 4.385,0.531 4.667,0.708 0.281,0.177 10 false E28
*a Front view of wire harness connector
(to ECM)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A25-13 (CANH) - A25-26 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A25-13 (CANH) - E28-16 (E1) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A25-26 (CANL) - E28-16 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A25-13 (CANH) - A25-1 (BATT) B - GR HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A25-26 (CANL) - A25-1 (BATT) W - GR LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 15 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A25-12 (CANP) - A25-25 (CANN) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A25-12 (CANP) - E28-16 (E1) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A25-25 (CANN) - E28-16 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A25-12 (CANP) - A25-1 (BATT) B - GR HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A25-25 (CANN) - A25-1 (BATT) W - GR LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


E224288C23
1.76,0.219 2.135,0.448 0.375,0.229 5.021,0.219 5.396,0.448 0.375,0.229 1.948,1.51 2.104,1.51 2.104,1.51 2.104,1.125 true 2.375,1.51 2.208,1.51 2.208,1.51 2.208,1.125 true 1.865,0.25 2.219,0.531 0.354,0.281 10 false I18 5.125,0.25 5.5,0.583 0.375,0.333 10 false I17 0.125,0.094 0.469,0.396 0.344,0.302 10 false *a 1.521,1.438 1.958,1.698 0.438,0.26 10 false CANH 2.448,1.427 2.885,1.688 0.438,0.26 10 false CANL
*a Component without harness connected
(Combination Meter Assembly)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
E224284C99
1.406,0.24 1.896,0.531 0.49,0.292 1.844,2.156 1.844,2.625 1.844,2.625 2.031,2.625 true 1.354,2.156 1.354,2.625 1.354,2.625 1.167,2.625 true 0.979,1.906 0.979,0.854 0.979,0.854 0.698,0.854 true 1.5,2.146 1.5,2.917 1.5,2.917 1.313,2.917 true 0.104,0.104 0.385,0.385 0.281,0.281 10 false *a 0.875,2.844 1.406,3.083 0.531,0.24 10 false CANH 0.76,2.552 1.292,2.792 0.531,0.24 10 false CANL 0.542,0.76 0.844,1.021 0.302,0.26 10 false B 2.146,2.542 2.458,2.813 0.313,0.271 10 false ES 1.552,0.292 1.833,0.469 0.281,0.177 10 false I18
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the I18 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I18-17 (CANH) - I18-16 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
I18-17 (CANH) - I18-20 (ES) R - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I18-16 (CANL) - I18-20 (ES) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I18-17 (CANH) - I18-1 (B) R - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I18-16 (CANL) - I18-1 (B) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


B278841C74
2.188,3.771 2.51,3.979 0.323,0.208 5.833,5.042 6.156,5.25 0.323,0.208 3.865,5.052 4.188,5.26 0.323,0.208 1.083,5.01 1.406,5.219 0.323,0.208 1.74,6.292 2.063,6.5 0.323,0.208 4.885,6.292 5.208,6.5 0.323,0.208 3.375,7.531 3.698,7.74 0.323,0.208 4.646,3.771 4.969,3.979 0.323,0.208 4.042,1.125 4.042,0.844 4.042,0.844 4.156,0.844 true 1.677,1.594 1.938,1.594 true 1.677,1.99 1.938,1.99 true 1.031,2.76 0.583,2.76 true 1.688,0.958 1.813,0.729 1.813,0.729 1.969,0.729 true 1.563,1.625 1.479,1.625 1.479,1.625 1.479,3.167 true 1.563,2.021 1.479,2.021 true 2.469,4.542 2.469,4.917 2.469,4.917 2.292,4.917 true 4.604,4.531 4.604,4.906 4.604,4.906 4.427,4.906 true 2.552,4.542 2.552,4.917 2.552,4.917 2.74,4.917 true 4.688,4.542 4.688,4.917 4.688,4.917 4.875,4.917 true 4.208,0.781 4.594,1 0.385,0.219 10 false MB 3.438,7.552 3.906,7.813 0.469,0.26 10 false MB 0.906,1.479 1.156,1.781 0.25,0.302 10 false 3C 1.156,5.031 1.438,5.385 0.281,0.354 10 false 3C 5.865,1.427 6.125,1.698 0.26,0.271 10 false 3B 1.823,6.313 2.094,6.573 0.271,0.26 10 false 3B 5.865,2.115 6.167,2.5 0.302,0.385 10 false 3A 4.969,6.313 5.229,6.594 0.26,0.281 10 false 3A 0.917,2.104 1.115,2.396 0.198,0.292 10 false 3D 3.938,5.073 4.167,5.292 0.229,0.219 10 false 3D 1.99,1.521 2.344,1.74 0.354,0.219 10 false I13 4.719,3.802 5.01,4.063 0.292,0.26 10 false I13 1.99,1.906 2.375,2.156 0.385,0.25 10 false I12 2.26,3.802 2.563,4.031 0.302,0.229 10 false I12 0.406,2.688 0.667,2.927 0.26,0.24 10 false 3F 5.906,5.063 6.313,5.479 0.406,0.417 10 false 3F 0.156,0.156 0.521,0.479 0.365,0.323 10 false *a 2,0.667 2.302,0.938 0.302,0.271 10 false *1 1.417,3.188 1.719,3.458 0.302,0.271 10 false *2 2.833,4.833 3.313,5.042 0.479,0.208 10 false CANP 1.854,4.844 2.333,5.052 0.479,0.208 10 false CANN 4.01,4.833 4.49,5.042 0.479,0.208 10 false CANH 4.948,4.833 5.427,5.042 0.479,0.208 10 false CANL
*1 Main Body ECU (Multiplex Network Body ECU)) *2 2 connectors
*a Component without harness connected
(Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU))
- -


B282096C85
2.26,3.823 2.583,4.031 0.323,0.208 3.938,5.115 4.26,5.323 0.323,0.208 1.156,5.094 1.479,5.302 0.323,0.208 1.813,6.344 2.135,6.552 0.323,0.208 4.969,6.344 5.292,6.552 0.323,0.208 3.448,7.583 3.771,7.792 0.323,0.208 4.719,3.823 5.042,4.031 0.323,0.208 5.802,5.094 6.125,5.302 0.323,0.208 4.115,1.135 4.115,0.854 4.115,0.854 4.229,0.854 true 1.813,2.146 2.104,2.146 true 1.813,1.792 2.094,1.792 true 0.76,2.781 1.031,2.781 true 1.865,0.979 2.073,0.552 2.073,0.552 2.188,0.552 true 1.594,3.177 1.594,1.5 1.594,1.5 1.708,1.5 true 1.594,1.865 1.698,1.865 true 1.594,2.208 1.698,2.208 true 2.292,4.917 2.469,4.917 2.469,4.917 2.469,4.542 true 4.427,4.917 4.604,4.917 4.604,4.917 4.604,4.542 true 2.74,4.917 2.552,4.917 2.552,4.917 2.552,4.542 true 4.875,4.917 4.688,4.917 4.688,4.917 4.688,4.542 true 3.51,7.604 3.875,7.854 0.365,0.25 10 false MB 1.229,5.115 1.594,5.385 0.365,0.271 10 false 3C 1.896,6.365 2.208,6.635 0.313,0.271 10 false 3B 5.042,6.365 5.469,6.583 0.427,0.219 10 false 3A 4.01,5.135 4.385,5.469 0.375,0.333 10 false 3D 4.792,3.854 5.073,4.073 0.281,0.219 10 false I13 2.333,3.854 2.635,4.042 0.302,0.188 10 false I12 5.854,2.135 6.115,2.354 0.26,0.219 10 false 3A 2.135,2.063 2.479,2.323 0.344,0.26 10 false I12 2.135,1.708 2.438,1.969 0.302,0.26 10 false I13 0.896,2.135 1.229,2.417 0.333,0.281 10 false 3D 2.24,0.479 2.469,0.802 0.229,0.323 10 false *1 0.563,2.719 0.854,2.948 0.292,0.229 10 false 3F 0.896,1.51 1.177,1.771 0.281,0.26 10 false 3C 5.865,1.49 6.177,1.74 0.313,0.25 10 false 3B 5.885,5.115 6.135,5.396 0.25,0.281 10 false 3F 4.292,0.781 4.615,1.01 0.323,0.229 10 false MB 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 1.531,3.229 1.875,3.49 0.344,0.26 10 false *2 1.865,4.833 2.323,5.073 0.458,0.24 10 false CANN 2.813,4.833 3.271,5.073 0.458,0.24 10 false CANP 4,4.833 4.458,5.073 0.458,0.24 10 false CANH 4.958,4.833 5.417,5.073 0.458,0.24 10 false CANL
*1 Main Body ECU (Multiplex Network Body ECU)) *2 3 connectors
*a Component without harness connected
(Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the I12 and I13 main body ECU (multiplex network body ECU) connectors.

C204058C22
1.792,0.542 2.125,0.76 0.333,0.219 2.146,3.594 2.479,3.813 0.333,0.219 4.771,0.573 5.104,0.792 0.333,0.219 2.708,0.75 2.594,0.75 2.594,0.75 2.052,1.677 true 2.771,1.021 2.635,1.021 2.635,1.021 2.146,1.677 true 5.656,0.708 5.531,0.708 5.531,0.708 5.052,1.656 true 5.854,0.99 5.688,0.99 5.688,0.99 5.125,1.656 true 4.771,4.167 4.625,4.167 4.625,4.167 4.292,3.99 true 3.979,2.844 3.729,2.844 3.729,2.844 3.573,3.417 true 0.969,0.417 1.24,0.729 0.271,0.313 10 false *a 1.979,2.802 2.448,3.094 0.469,0.292 10 false *1 4.854,4.073 5.146,4.25 0.292,0.177 10 false BAT 1.875,0.563 2.25,0.865 0.375,0.302 10 false I12 2.229,3.604 2.552,3.823 0.323,0.219 10 false I39 4.854,0.594 5.198,0.865 0.344,0.271 10 false I13 2.75,0.688 3.333,0.99 0.583,0.302 10 false CANP 2.823,0.948 3.396,1.24 0.573,0.292 10 false CANN 5.698,0.625 6.281,0.885 0.583,0.26 10 false CANL 5.906,0.906 6.479,1.26 0.573,0.354 10 false CANH 4.031,2.792 4.438,2.969 0.406,0.177 10 false CG
*1 DLC3 - -
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I13-14 (CANH) - I13-13 (CANL) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I13-14 (CANH) - I39-4 (CG) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I13-13 (CANL) - I39-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I13-14 (CANH) - I39-16 (BAT) P - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I13-13 (CANL) - I39-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 1 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I12-9 (CANP) - I12-10 (CANN) R - GR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
I12-9 (CANP) - I39-4 (CG) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I12-10 (CANN) - I39-4 (CG) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I12-9 (CANP) - I39-16 (BAT) R - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I12-10 (CANN) - I39-16 (BAT) GR - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)


C156569C32
3.406,0.604 3.781,0.833 0.375,0.229 3.094,2.24 3.25,2.24 3.25,2.24 3.25,1.875 true 3.135,2.521 3.354,2.521 3.354,2.521 3.354,1.875 true 3.813,2.229 3.667,2.229 3.667,2.229 3.667,1.865 true 3.802,2.521 3.563,2.521 3.563,2.521 3.563,1.875 true 0.25,0.188 0.49,0.365 0.24,0.177 10 false *a 3.479,0.635 3.865,0.906 0.385,0.271 10 false A28 2.719,2.135 3.104,2.406 0.385,0.271 10 false CA1L 2.729,2.427 3.167,2.698 0.438,0.271 10 false CA1H 3.865,2.125 4.25,2.396 0.385,0.271 10 false CA2L 3.865,2.427 4.25,2.698 0.385,0.271 10 false CA2H
*a Component without harness connected
(Brake Booster with Master Cylinder Assembly (Skid Control ECU))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C297192C32
1.49,0.583 1.865,0.833 0.375,0.25 1.479,2.719 1.656,2.719 1.656,2.719 1.656,2.146 true 1.583,2.958 1.76,2.958 1.76,2.958 1.76,2.156 true 2.188,3.052 1.958,3.052 1.958,3.052 1.958,2.135 true 2.188,2.75 2.052,2.75 2.052,2.75 2.052,2.146 true 2.854,2.771 2.646,2.771 2.646,2.771 2.646,2.052 true 2.438,0.865 2.625,0.865 2.625,0.865 2.625,1.719 true 0.115,0.135 0.427,0.333 0.313,0.198 10 false *a 1.552,0.625 1.865,0.823 0.313,0.198 10 false A28 1.094,2.635 1.813,2.823 0.719,0.188 10 false CA2L 1.177,2.885 2.01,3.146 0.833,0.26 10 false CA2H 2.26,2.979 3.01,3.219 0.75,0.24 10 false CA1H 2.219,2.667 2.823,2.958 0.604,0.292 10 false CA1L 2.917,2.688 3.271,2.927 0.354,0.24 10 false GND 2.188,0.792 2.542,1.031 0.354,0.24 10 false BS
*a Front view of wire harness connector
(Brake Booster with Master Cylinder Assembly (Skid Control ECU))


Disconnect the A28 brake booster with master cylinder assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A28-37 (CA1H) - A28-38 (CA1L) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A28-37 (CA1H) - A28-28 (GND) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A28-38 (CA1L) - A28-28 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A28-37 (CA1H) - A28-15 (BS) GR - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A28-38 (CA1L) - A28-15 (BS) W - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 15 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A28-35 (CA2H) - A28-34 (CA2L) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A28-35 (CA2H) - A28-28 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A28-34 (CA2L) - A28-28 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A28-35 (CA2H) - A28-15 (BS) B - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A28-34 (CA2L) - A28-15 (BS) W - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




STEERING SENSOR


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C156493C90
1.188,0.792 1.677,1.083 0.49,0.292 1.219,3.219 1.531,3.219 1.531,3.219 1.531,2.698 true 0.854,2.99 1.344,2.99 1.344,2.99 1.344,2.708 true 2.021,3.219 1.708,3.219 1.708,3.219 1.708,2.698 true 2.573,2.979 2.083,2.979 2.083,2.979 2.083,2.698 true 0.167,0.156 0.552,0.51 0.385,0.354 10 false *a 0.531,2.927 1.115,3.208 0.583,0.281 10 false ESS 0.833,3.156 1.427,3.417 0.594,0.26 10 false CANL 2.073,3.146 2.698,3.365 0.625,0.219 10 false CANH 2.646,2.906 3.083,3.167 0.438,0.26 10 false BAT 1.344,0.854 1.792,1.146 0.448,0.292 10 false I30
*a Front view of wire harness connector
(to Steering Sensor)


Disconnect the I30 steering sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I30-3 (CANH) - I30-2 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I30-3 (CANH) - I30-1 (ESS) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I30-2 (CANL) - I30-1 (ESS) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I30-3 (CANH) - I30-5 (BAT) V - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I30-2 (CANL) - I30-5 (BAT) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POWER STEERING ECU ASSEMBLY


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.

C239855C26
3.729,0.198 4.052,0.396 0.323,0.198 5.719,0.198 6.042,0.396 0.323,0.198 3.906,1.844 4.229,2.042 0.323,0.198 4.708,1.844 5.031,2.042 0.323,0.198 5.563,1.844 5.885,2.042 0.323,0.198 1.875,0.833 2.198,1.031 0.323,0.198 0.719,1.313 1.042,1.51 0.323,0.198 1.104,1.313 1.427,1.51 0.323,0.198 1.479,1.313 1.802,1.51 0.323,0.198 0.688,3.469 1.01,3.667 0.323,0.198 0.906,1.313 1.031,1.146 false 1.271,1.313 1.292,1.146 false 1.625,1.313 1.542,1.146 false 2.021,0.833 2.021,0.771 false 1.01,3.521 1.083,3.49 false 3.385,2.594 3.781,2.594 true 3.385,2.729 3.781,2.729 true 3.854,0.198 4.188,0.427 0.333,0.229 10 false j2 5.833,0.198 6.083,0.344 0.25,0.146 10 false c 4.021,1.844 4.281,2.156 0.26,0.313 10 false j3 4.833,1.844 5.073,2.073 0.24,0.229 10 false a 5.698,1.844 5.948,2.094 0.25,0.25 10 false b 0.135,0.115 0.417,0.344 0.281,0.229 10 false *a 1.99,0.833 2.344,1.115 0.354,0.281 10 false j2 0.833,1.313 1.135,1.573 0.302,0.26 10 false j3 1.219,1.313 1.51,1.604 0.292,0.292 10 false a 1.604,1.313 1.979,1.583 0.375,0.271 10 false b 0.823,3.469 1.073,3.615 0.25,0.146 10 false c 2.927,2.51 3.365,2.75 0.438,0.24 10 false CANH 2.938,2.667 3.375,2.906 0.438,0.24 10 false CANL
*a Component without harness connected
(Power Steering ECU Assembly)
- -



b.

Disconnect the j2 and j3 power steering ECU assembly connectors.

C250526C05
0.708,1.51 1.104,1.75 0.396,0.24 4.708,0.865 5.104,1.104 0.396,0.24 2.104,2 2.469,2 true 2.104,1.844 2.458,1.844 true 4.083,1.823 4.417,1.823 true 5.406,1.823 5.74,1.823 true 0.125,0.115 0.458,0.438 0.333,0.323 10 false *a 2.542,1.938 2.969,2.115 0.427,0.177 10 false CANL 2.521,1.771 2.979,1.948 0.458,0.177 10 false CANH 3.802,1.75 4.271,2.031 0.469,0.281 10 false PIG 5.792,1.76 6.344,2.042 0.552,0.281 10 false PGND 0.844,1.531 1.208,1.833 0.365,0.302 10 false j3 4.854,0.896 5.083,1.135 0.229,0.24 10 false j2
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
j3-4 (CANH) - j3-8 (CANL) Y - SB HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
j3-4 (CANH) - j2-2 (PGND) Y - B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
j3-8 (CANL) - j2-2 (PGND) SB - B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
j3-4 (CANH) - j2-1 (PIG) Y - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
j3-8 (CANL) - j2-1 (PIG) SB - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIRBAG SENSOR ASSEMBLY


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the I47 airbag sensor assembly connector.

C188802C34
0.552,1.552 0.927,1.76 0.375,0.208 3.323,1.594 3.698,1.802 0.375,0.208 1.333,1.083 1.51,1.083 1.51,1.083 1.51,1.615 true 1.417,1.885 1.417,2.271 1.417,2.271 1.24,2.271 true 1.698,1.875 1.698,2.271 1.698,2.271 1.875,2.271 true 5.698,1.969 5.698,2.354 5.698,2.354 5.896,2.354 true 0.188,0.146 2.583,0.5 2.396,0.354 10 false *a 0.844,2.188 1.323,2.458 0.479,0.271 10 false CANL 0.917,1 1.406,1.198 0.49,0.198 10 false CANH 1.938,2.198 2.26,2.438 0.323,0.24 10 false E1 6,2.271 6.354,2.438 0.354,0.167 10 false BAT 0.646,1.573 1.094,1.865 0.448,0.292 10 false I47 3.396,0.156 3.844,0.438 0.448,0.281 10 false *1 3.427,1.625 3.854,1.896 0.427,0.271 10 false I39
*1 DLC3 - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I47-13 (CANH) - I47-22 (CANL) Y - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I47-13 (CANH) - I47-25 (E1) Y - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I47-22 (CANL) - I47-25 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I47-13 (CANH) - I39-16 (BAT) Y - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I47-22 (CANL) - I39-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




SMART KEY ECU ASSEMBLY (CERTIFICATION ECU)


C244122C11
1.677,1.625 2.094,1.885 0.417,0.26 3.406,1.625 3.823,1.885 0.417,0.26 4.865,1.615 5.281,1.875 0.417,0.26 3.896,0.656 4.104,0.656 4.104,0.656 4.104,1.219 true 4.458,0.656 4.229,0.656 4.229,0.656 4.229,1.219 true 1.781,1.677 2.021,1.875 0.24,0.198 10 false O2 0.094,0.094 0.406,0.385 0.313,0.292 10 false *a 3.521,1.677 3.76,1.875 0.24,0.198 10 false I87 4.969,1.667 5.208,1.865 0.24,0.198 10 false I86 3.5,0.573 3.958,0.792 0.458,0.219 10 false CANL 4.521,0.573 4.979,0.792 0.458,0.219 10 false CANH
*a Component without harness connected
(Smart Key ECU Assembly (Certification ECU))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the I86 and I87 smart key ECU assembly (certification ECU) connectors.

C250527C11
1.542,2.156 1.927,2.375 0.385,0.219 5.365,2.156 5.75,2.375 0.385,0.219 0.979,0.99 1.042,0.99 1.042,0.99 1.042,1.635 true 4.781,1.01 4.844,1.01 4.844,1.01 4.844,1.656 true 1.229,0.99 1.167,0.99 1.167,0.99 1.167,1.625 true 2.469,0.99 2.406,0.99 2.406,0.99 2.406,1.625 true 0.104,0.073 0.354,0.281 0.25,0.208 10 false *a 0.573,0.927 1.146,1.188 0.573,0.26 10 false CANH 1.646,2.198 2.094,2.583 0.448,0.385 10 false I87 1.302,0.917 1.844,1.135 0.542,0.219 10 false CANL 4.646,0.927 4.958,1.115 0.313,0.188 10 false E 2.531,0.896 2.979,1.052 0.448,0.156 10 false +B 5.479,2.198 5.865,2.469 0.385,0.271 10 false I86
*a Front view of wire harness connector
(to Smart Key ECU Assembly (Certification ECU))
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I87-1 (CANH) - I87-2 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I87-1 (CANH) - I86-1 (E) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I87-2 (CANL) - I86-1 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I87-1 (CANH) - I87-5 (+B) L - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I87-2 (CANL) - I87-5 (+B) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


E277812C40
2.167,0.188 2.563,0.375 0.396,0.188 2.229,1.594 2.625,1.781 0.396,0.188 1.438,1.594 1.833,1.781 0.396,0.188 3.792,1.573 4.188,1.76 0.396,0.188 5.271,1.427 5.667,1.615 0.396,0.188 4.469,0.188 4.865,0.375 0.396,0.188 4.219,1.302 4.375,1.302 4.375,1.302 4.375,0.833 true 4.656,1.302 4.49,1.302 4.49,1.302 4.49,0.833 true 2.229,0.198 2.583,0.396 0.354,0.198 10 false I175 4.531,0.198 4.979,0.427 0.448,0.229 10 false I155 1.5,1.604 1.906,1.802 0.406,0.198 10 false I152 2.292,1.604 2.802,1.865 0.51,0.26 10 false I153 3.865,1.583 4.219,1.781 0.354,0.198 10 false I156 5.375,1.427 5.729,1.625 0.354,0.198 10 false RA 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 3.792,1.229 4.24,1.458 0.448,0.229 10 false CANL 4.75,1.219 5.198,1.448 0.448,0.229 10 false CANH
*a Component without harness connected
(Radio and Display Receiver Assembly)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the I152 and I155 radio and display receiver assembly connectors.

C240506C48
0.604,1.448 1,1.688 0.396,0.24 3.875,1.448 4.271,1.688 0.396,0.24 1.844,0.552 2,0.552 2,0.552 2,1.688 true 2.333,0.552 2.115,0.552 2.115,0.552 2.115,1.688 true 5.781,0.531 5.625,0.531 5.625,0.531 5.625,1.51 true 5.177,2.292 5.01,2.292 5.01,2.292 5.01,1.896 true 0.135,0.052 0.313,0.229 0.177,0.177 10 false *a 2.417,0.49 3.073,0.802 0.656,0.313 10 false CANL 1.427,0.479 2.073,0.813 0.646,0.333 10 false CANH 5.865,0.448 6.25,0.74 0.385,0.292 10 false +B1 5.229,2.219 5.823,2.51 0.594,0.292 10 false GND1 0.656,1.49 1.021,1.75 0.365,0.26 10 false I155 3.948,1.49 4.406,1.792 0.458,0.302 10 false I152
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I155-9 (CANH) - I155-10 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I155-9 (CANH) - I152-7 (GND1) R - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I155-10 (CANL) - I152-7 (GND1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I155-9 (CANH) - I152-4 (+B1) R - L-Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I155-10 (CANL) - I152-4 (+B1) W - L-Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type)


E277812C31
2.146,0.198 2.542,0.385 0.396,0.188 2.229,1.594 2.625,1.781 0.396,0.188 1.438,1.594 1.833,1.781 0.396,0.188 3.792,1.552 4.188,1.74 0.396,0.188 5.271,1.427 5.667,1.615 0.396,0.188 4.469,0.083 4.865,0.271 0.396,0.188 4.375,0.76 4.375,0.354 4.375,0.354 4.208,0.354 true 4.49,0.76 4.49,0.354 4.49,0.354 4.646,0.354 true 2.219,0.208 2.573,0.406 0.354,0.198 10 false I174 4.583,0.094 4.938,0.292 0.354,0.198 10 false I67 1.542,1.594 1.896,1.792 0.354,0.198 10 false I64 2.344,1.594 2.698,1.792 0.354,0.198 10 false I65 3.875,1.552 4.229,1.75 0.354,0.198 10 false I147 5.375,1.427 5.729,1.625 0.354,0.198 10 false RA 0.229,0.146 0.583,0.344 0.354,0.198 10 false *a 3.781,0.292 4.219,0.49 0.438,0.198 10 false CANL 4.708,0.292 5.146,0.49 0.438,0.198 10 false CANH
*a Component without harness connected
(Navigation Receiver Assembly)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the I64 and I67 navigation receiver assembly connectors.

C240506C49
0.594,1.49 0.99,1.729 0.396,0.24 3.875,1.479 4.271,1.719 0.396,0.24 1.854,0.552 2.01,0.552 2.01,0.552 2.01,1.688 true 2.333,0.542 2.115,0.542 2.115,0.542 2.115,1.677 true 5.781,0.531 5.625,0.531 5.625,0.531 5.625,1.51 true 5.177,2.302 5.01,2.302 5.01,2.302 5.01,1.906 true 0.125,0.125 0.448,0.469 0.323,0.344 10 false *a 2.417,0.469 2.948,0.688 0.531,0.219 10 false CANL 1.427,0.469 1.99,0.719 0.563,0.25 10 false CANH 5.885,0.448 6.26,0.708 0.375,0.26 10 false +B1 5.24,2.229 5.688,2.417 0.448,0.188 10 false GND1 0.708,1.531 1.063,1.854 0.354,0.323 10 false I67 3.979,1.521 4.333,1.792 0.354,0.271 10 false I64
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I67-9 (CANH) - I67-10 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I67-9 (CANH) - I64-7 (GND1) R - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I67-10 (CANL) - I64-7 (GND1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I67-9 (CANH) - I64-4 (+B1) R - L-Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I67-10 (CANL) - I64-4 (+B1) W - L-Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


E226604C29
2.958,0.115 3.292,0.344 0.333,0.229 5.083,0.115 5.417,0.344 0.333,0.229 2.708,0.417 2.885,0.417 2.885,0.417 2.885,0.875 true 3.375,0.417 3.031,0.417 3.031,0.417 3.031,0.875 true 5.188,0.156 5.49,0.385 0.302,0.229 10 false z1 3.031,0.156 3.344,0.313 0.313,0.156 10 false I77 0.104,0.094 0.427,0.313 0.323,0.219 10 false *a 3.427,0.333 3.917,0.51 0.49,0.177 10 false CANH 2.323,0.333 2.813,0.51 0.49,0.177 10 false CANL
*a Component without harness connected
(Air Conditioning Amplifier Assembly)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the I77 air conditioning amplifier assembly connector.

C188799C22
1.75,1.75 2.146,1.948 0.396,0.198 3.625,1.938 3.625,0.802 3.625,0.802 3.396,0.802 true 3.729,1.938 3.729,0.938 3.729,0.938 4.052,0.938 true 2.677,2.146 2.677,2.458 2.677,2.458 2.49,2.458 true 4.198,1.25 3.917,1.25 3.917,1.25 3.917,1.948 true 0.219,0.177 0.656,0.521 0.438,0.344 10 false *a 4.125,0.854 4.573,1.021 0.448,0.167 10 false CANL 2.969,0.719 3.417,0.885 0.448,0.167 10 false CANH 2.354,2.375 2.531,2.542 0.177,0.167 10 false B 4.26,1.167 4.688,1.333 0.427,0.167 10 false GND 1.854,1.771 2.177,1.948 0.323,0.177 10 false I77
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I77-11 (CANH) - I77-12 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I77-11 (CANH) - I77-14 (GND) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I77-12 (CANL) - I77-14 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I77-11 (CANH) - I77-21 (B) V - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I77-12 (CANL) - I77-21 (B) W - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY (for Driver Side) (w/ Seat Position Memory System)


B209687C59
2.896,0.219 3.219,0.427 0.323,0.208 4.042,0.229 4.365,0.438 0.323,0.208 4.146,1.458 4.375,1.458 4.375,1.458 4.375,1.031 true 4.688,1.458 4.479,1.458 4.479,1.458 4.479,1.031 true 2.938,0.25 3.219,0.448 0.281,0.198 10 false z17 4.094,0.25 4.375,0.469 0.281,0.219 10 false J13 0.146,0.115 0.76,0.542 0.615,0.427 10 false *a 3.74,1.375 4.24,1.583 0.5,0.208 10 false CANP 4.75,1.365 5.25,1.573 0.5,0.208 10 false CANN
*a Component without harness connected
(Outer Mirror Control ECU Assembly (for Driver Side))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C204179C81
1.51,0.25 1.896,0.458 0.385,0.208 1.042,1.896 1.25,1.896 1.25,1.896 1.25,1.406 true 1.385,1.417 1.385,1.896 1.385,1.896 1.583,1.896 true 2.198,1.135 2.573,1.135 true 2.531,0.615 2.302,0.615 2.302,0.615 1.979,1.135 true 0.094,0.073 0.521,0.365 0.427,0.292 10 false *a 1.635,1.813 2.115,2.042 0.479,0.229 10 false CANP 0.635,1.813 1.094,2.01 0.458,0.198 10 false CANN 2.635,1.063 3.042,1.344 0.406,0.281 10 false GND 2.583,0.542 3.052,0.802 0.469,0.26 10 false CPUB 1.594,0.271 1.885,0.542 0.292,0.271 10 false J13
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Driver Side))


Disconnect the J13 outer mirror control ECU assembly (for driver side) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J13-9 (CANP) - J13-8 (CANN) P - GR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
J13-9 (CANP) - J13-7 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
J13-8 (CANN) - J13-7 (GND) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
J13-9 (CANP) - J13-6 (CPUB) P - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
J13-8 (CANN) - J13-6 (CPUB) GR - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY (for Front Passenger Side) (w/ Seat Position Memory System)


B209687C60
2.854,0.219 3.177,0.427 0.323,0.208 4,0.229 4.323,0.438 0.323,0.208 4.177,1.438 4.375,1.438 4.375,1.438 4.375,1.031 true 4.667,1.438 4.479,1.438 4.479,1.438 4.479,1.031 true 2.896,0.25 3.188,0.458 0.292,0.208 10 false z16 4.031,0.25 4.313,0.469 0.281,0.219 10 false K12 0.094,0.083 0.448,0.365 0.354,0.281 10 false *a 3.771,1.344 4.271,1.583 0.5,0.24 10 false CANP 4.719,1.344 5.219,1.583 0.5,0.24 10 false CANN
*a Component without harness connected
(Outer Mirror Control ECU Assembly (for Front Passenger Side))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C204179C82
1.5,0.25 1.906,0.469 0.406,0.219 1.021,1.896 1.24,1.896 1.24,1.896 1.24,1.427 true 1.396,1.427 1.396,1.896 1.396,1.896 1.604,1.896 true 2.198,1.115 2.573,1.115 true 2.583,0.615 2.302,0.615 2.302,0.615 1.979,1.135 true 0.094,0.094 0.521,0.385 0.427,0.292 10 false *a 1.656,1.813 2.115,2.021 0.458,0.208 10 false CANP 0.615,1.823 1.156,2.083 0.542,0.26 10 false CANN 2.604,1.031 2.927,1.208 0.323,0.177 10 false GND 2.625,0.542 3.083,0.823 0.458,0.281 10 false CPUB 1.563,0.281 1.833,0.5 0.271,0.219 10 false K12
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Front Passenger Side))


Disconnect the K12 outer mirror control ECU assembly (for front passenger side) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K12-9 (CANP) - K12-8 (CANN) G - GR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
K12-9 (CANP) - K12-7 (GND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K12-8 (CANN) - K12-7 (GND) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K12-9 (CANP) - K12-6 (CPUB) G - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K12-8 (CANN) - K12-6 (CPUB) GR - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POSITION CONTROL ECU AND SWITCH ASSEMBLY (for Driver Side) (w/ Seat Position Memory System)


B219505C23
2.802,0.083 3.208,0.333 0.406,0.25 3.688,0.083 4.083,0.333 0.396,0.25 2.24,1.469 3.052,1.469 3.052,1.469 3.052,1.219 true 2.24,1.646 3.135,1.646 3.135,1.646 3.135,1.229 true 3.781,0.125 4.333,0.375 0.552,0.25 10 false d11 2.885,0.115 3.469,0.375 0.583,0.26 10 false d12 0.073,0.083 0.792,0.677 0.719,0.594 10 false *a 1.833,1.375 2.417,1.635 0.583,0.26 10 false CANP 1.833,1.563 2.313,1.75 0.479,0.188 10 false CANN
*a Component without harness connected
(Position Control ECU and Switch Assembly (for Driver Side))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the d11 and d12 position control ECU and switch assembly (for driver side) connectors.

C204065C30
1.958,0.573 2.302,0.781 0.344,0.208 4.854,0.438 5.219,0.656 0.365,0.219 4.969,2.51 4.771,2.51 4.771,2.51 4.771,2.115 true 4.448,2.51 4.646,2.51 4.646,2.51 4.646,2.125 true 1.573,1.323 1.823,1.323 1.823,1.323 1.823,1.771 true 1.594,2.438 1.823,2.438 1.823,2.438 1.823,2.063 true 0.063,0.063 0.708,0.354 0.646,0.292 10 false *a 2.021,0.594 2.313,0.823 0.292,0.229 10 false d11 4.927,0.469 5.25,0.646 0.323,0.177 10 false d12 5.021,2.417 5.51,2.594 0.49,0.177 10 false CANP 4.021,2.417 4.521,2.594 0.5,0.177 10 false CANN 1.219,1.24 1.781,1.469 0.563,0.229 10 false GND 1.292,2.344 1.656,2.51 0.365,0.167 10 false +B
*a Front view of wire harness connector
(to Position Control ECU and Switch Assembly (for Driver Side))
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
d12-8 (CANP) - d12-7 (CANN) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
d12-8 (CANP) - d11-2 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
d12-7 (CANN) - d11-2 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
d12-8 (CANP) - d11-7 (+B) L - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
d12-7 (CANN) - d11-7 (+B) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CLEARANCE WARNING ECU ASSEMBLY (w/ Toyota Parking Assist-sensor System)


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the I82 clearance warning ECU assembly connector.

C240483C17
1.198,0.698 1.573,0.927 0.375,0.229 4.896,0.698 5.271,0.927 0.375,0.229 3.073,0.958 2.813,0.958 2.813,0.958 2.813,1.781 true 2.427,0.958 2.719,0.958 2.719,0.958 2.719,1.792 true 2.156,2.365 1.99,2.365 1.99,2.365 1.99,1.917 true 5.885,2.375 5.708,2.375 5.708,2.375 5.708,1.969 true 0.125,0.104 0.313,0.292 0.188,0.188 10 false *a 3.604,0.104 3.792,0.292 0.188,0.188 10 false *1 5.948,2.281 6.271,2.469 0.323,0.188 10 false BAT 2.188,2.26 2.365,2.448 0.177,0.188 10 false E 3.104,0.865 3.344,1.052 0.24,0.188 10 false R2 2.24,0.865 2.479,1.052 0.24,0.188 10 false R1 1.292,0.74 1.51,0.906 0.219,0.167 10 false I82 5,0.74 5.292,0.906 0.292,0.167 10 false I39
*1 DLC3 - -
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I82-17 (R1) - I82-18 (R2) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I82-17 (R1) - I82-30 (E) P - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I82-18 (R2) - I82-30 (E) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I82-17 (R1) - I39-16 (BAT) P - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I82-18 (R2) - I39-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




REAR TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System without Parallel Parking Assist Function)


C302330C07
3.323,0.198 3.729,0.406 0.406,0.208 3.938,1.698 4.385,2.229 4.385,2.229 4.667,2.229 true 3.917,1.333 4.396,1.021 4.396,1.021 4.677,1.021 true 0.198,0.135 0.51,0.333 0.313,0.198 10 false *a 3.417,0.219 3.729,0.448 0.313,0.229 10 false T22 4.792,0.938 5.271,1.208 0.479,0.271 10 false CANL 4.833,2.146 5.313,2.417 0.479,0.271 10 false CANH
*a Component without harness connected
(Rear Television Camera Assembly)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the T22 rear television camera assembly connector.

C295280C14
1.979,0.094 2.375,0.365 0.396,0.271 5.042,0.083 5.438,0.354 0.396,0.271 1.594,1.49 1.719,1.49 1.719,1.49 2.01,1.094 true 1.563,0.344 1.688,0.344 1.688,0.344 2.01,0.844 true 5.146,0.667 4.792,0.271 4.792,0.271 4.656,0.271 true 6.198,1.521 6.083,1.521 6.083,1.521 5.875,1.146 true 0.896,0.083 1.208,0.281 0.313,0.198 10 false *a 2.073,0.135 2.531,0.333 0.458,0.198 10 false T22 1.135,1.406 1.75,1.604 0.615,0.198 10 false CANH 1.125,0.26 1.74,0.458 0.615,0.198 10 false CANL 4.385,0.188 5,0.385 0.615,0.198 10 false CG 5.115,0.125 5.573,0.323 0.458,0.198 10 false I39 6.292,1.438 6.75,1.635 0.458,0.198 10 false BAT 3.906,0.125 4.219,0.323 0.313,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to Rear Television Camera Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
T22-4 (CANH) - T22-1 (CANL) V - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
T22-4 (CANH) - I39-4 (CG) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
T22-1 (CANL) - I39-4 (CG) P - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
T22-4 (CANH) - I39-16 (BAT) V - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
T22-1 (CANL) - I39-16 (BAT) P - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BLIND SPOT MONITOR SENSOR RH (w/ Blind Spot Monitor System)


E233761C32
2.26,0.573 2.646,0.813 0.385,0.24 3.75,0.802 3.958,0.323 3.958,0.323 4.198,0.323 true 3.76,1.052 4.115,1.427 4.115,1.427 4.281,1.427 true 2.323,0.594 2.76,0.969 0.438,0.375 10 false O47 0.063,0.031 0.49,0.427 0.427,0.396 10 false *a 4.271,0.229 4.885,0.427 0.615,0.198 10 false CA1P 4.344,1.323 4.958,1.521 0.615,0.198 10 false CA1N
*a Component without harness connected
(Blind Spot Monitor Sensor RH)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the O47 blind spot monitor sensor RH connector.

C250047C13
3.51,1.521 3.885,1.75 0.375,0.229 0.885,1.51 1.281,1.75 0.396,0.24 5.719,1.938 5.719,2.385 5.719,2.385 5.865,2.385 true 2.323,1.896 2.323,2.344 2.323,2.344 2.438,2.344 true 1.958,1.896 1.958,2.333 1.958,2.333 1.76,2.333 true 1.958,1.74 1.958,0.927 1.958,0.927 1.688,0.927 true 0.719,0.427 0.917,0.604 0.198,0.177 10 false *a 3.76,0.438 3.958,0.615 0.198,0.177 10 false *1 5.917,2.281 6.406,2.563 0.49,0.281 10 false BAT 3.604,1.552 4.094,1.927 0.49,0.375 10 false I39 0.958,1.552 1.417,1.938 0.458,0.385 10 false O47 2.479,2.24 3.031,2.5 0.552,0.26 10 false BRGD 1.354,2.229 1.948,2.531 0.594,0.302 10 false CA1N 1.292,0.813 1.792,1.104 0.5,0.292 10 false CA1P
*1 DLC3 - -
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O47-2 (CA1P) - O47-7 (CA1N) R - B HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
O47-2 (CA1P) - O47-10 (BRGD) R - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O47-7 (CA1N) - O47-10 (BRGD) B - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O47-2 (CA1P) - I39-16 (BAT) R - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O47-7 (CA1N) - I39-16 (BAT) B - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




LANE DEPARTURE WARNING CAMERA (w/ Lane Departure Alert System)


C265805C06
3.427,0.24 3.885,0.469 0.458,0.229 3.031,0.479 3.354,0.479 3.354,0.479 3.354,0.979 true 3.031,1.594 3.354,1.594 3.354,1.594 3.354,1.229 true 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 3.563,0.271 3.875,0.469 0.313,0.198 10 false S15 2.604,0.417 3.052,0.635 0.448,0.219 10 false CA1P 2.604,1.521 3.052,1.74 0.448,0.219 10 false CA1N
*a Component without harness connected
(Lane Departure Warning Camera)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the S15 lane departure warning camera connector.

C292389C06
1.771,0.083 2.198,0.354 0.427,0.271 5.104,0.063 5.531,0.333 0.427,0.271 5.948,1.167 6.198,1.542 6.198,1.542 6.323,1.542 true 2.281,0.917 2.646,0.49 2.646,0.49 2.76,0.49 true 2.292,1.146 2.573,1.469 2.573,1.469 2.677,1.469 true 2.146,1.146 1.958,1.625 1.958,1.625 1.833,1.625 true 0.677,0.083 0.99,0.281 0.313,0.198 10 false *a 3.51,0.083 3.823,0.281 0.313,0.198 10 false *1 1.875,0.115 2.188,0.313 0.313,0.198 10 false S15 5.229,0.104 5.542,0.302 0.313,0.198 10 false I39 6.396,1.448 6.854,1.646 0.458,0.198 10 false BAT 1.479,1.531 1.938,1.729 0.458,0.198 10 false GND 2.76,1.375 3.375,1.573 0.615,0.198 10 false CA1N 2.833,0.396 3.448,0.594 0.615,0.198 10 false CA1P
*1 DLC3 - -
*a Front view of wire harness connector
(to Lane Departure Warning Camera)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S15-6 (CA1P) - S15-12 (CA1N) V - LG HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
S15-6 (CA1P) - S15-11 (GND) V - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
S15-12 (CA1N) - S15-11 (GND) LG - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
S15-6 (CA1P) - I39-16 (BAT) V - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
S15-12 (CA1N) - I39-16 (BAT) LG - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




DRIVING SUPPORT ECU ASSEMBLY (w/ Pre-crash Safety System)


E184662C08
3.5,0.198 3.938,0.448 0.438,0.25 1.969,0.469 2.167,0.469 2.167,0.469 2.167,0.844 true 2.49,0.469 2.292,0.469 2.292,0.469 2.292,0.844 true 2.042,1.521 2.219,1.521 2.219,1.521 2.219,1.156 true 2.521,1.521 2.344,1.521 2.344,1.521 2.344,1.156 true 3.604,0.25 3.917,0.417 0.313,0.167 10 false I176 0.104,0.115 0.479,0.427 0.375,0.313 10 false *a 1.563,0.375 1.958,0.552 0.396,0.177 10 false CA1N 1.646,1.427 2.042,1.604 0.396,0.177 10 false CA1P 2.573,1.427 3,1.604 0.427,0.177 10 false CA2H 2.552,0.385 2.948,0.563 0.396,0.177 10 false CA2L
*a Component without harness connected
(Driving Support ECU Assembly)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
E251017C84
0.313,0.938 0.802,1.229 0.49,0.292 1.302,1.927 1.302,2.563 1.302,2.563 1.083,2.563 true 2.698,1.927 2.698,2.542 2.698,2.542 2.51,2.542 true 2.719,1.729 2.719,1 2.719,1 2.531,1 true 1.76,1.927 1.76,2.823 1.76,2.823 1.552,2.823 true 2.823,1.927 2.823,2.813 2.823,2.813 2.646,2.813 true 2.844,1.729 2.844,0.635 2.844,0.635 2.615,0.635 true 0.156,0.125 0.51,0.396 0.354,0.271 10 false *a 0.75,2.479 1.24,2.667 0.49,0.188 10 false GND 2.115,2.458 2.604,2.646 0.49,0.188 10 false CA2H 2.271,2.719 2.708,2.906 0.438,0.188 10 false CA1P 1.396,2.74 1.667,2.958 0.271,0.219 10 false B 2.156,0.917 2.552,1.104 0.396,0.188 10 false CA2L 2.219,0.552 2.615,0.74 0.396,0.188 10 false CA1N 0.417,0.99 0.74,1.167 0.323,0.177 10 false I176
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the I176 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
SUB Bus 11 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I176-39 (CA2H) - I176-17 (CA2L) L - LG HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
I176-39 (CA2H) - I176-25 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I176-17 (CA2L) - I176-25 (GND) LG - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I176-39 (CA2H) - I176-30 (B) L - V HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I176-17 (CA2L) - I176-30 (B) LG - V LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 13 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I176-40 (CA1P) - I176-18 (CA1N) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
I176-40 (CA1P) - I176-25 (GND) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I176-18 (CA1N) - I176-25 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I176-40 (CA1P) - I176-30 (B) LG - V HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I176-18 (CA1N) - I176-30 (B) W - V LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-crash Safety System)


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C287046C11
1.49,2.656 1.948,2.917 0.458,0.26 1.49,0.49 1.948,0.75 0.458,0.26 2.823,4.375 2.646,4.375 2.646,4.375 2.458,4.042 true 0.885,1.396 1.375,1.396 true 1.667,1.344 2,0.823 2,0.823 2.198,0.823 true 1.542,1.344 1.25,0.833 1.25,0.833 0.979,0.833 true 0.115,2.396 0.427,2.75 0.313,0.354 10 false *1 0.115,0.094 0.427,0.448 0.313,0.354 10 false *a 1.625,2.719 1.979,2.979 0.354,0.26 10 false I39 2.875,4.271 3.333,4.469 0.458,0.198 10 false BAT 2.25,0.729 2.865,1.052 0.615,0.323 10 false CA1P 0.583,0.729 1.198,1.052 0.615,0.323 10 false CA1N 1.594,0.552 1.906,0.75 0.313,0.198 10 false A76 0.448,1.323 1.063,1.521 0.615,0.198 10 false SGND
*1 DLC3
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A76 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A76-3 (CA1P) - A76-2 (CA1N) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A76-3 (CA1P) - A76-1 (SGND) B - L HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A76-2 (CA1N) - A76-1 (SGND) W - L LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A76-3 (CA1P) - I39-16 (BAT) B - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A76-2 (CA1N) - I39-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher